Yamaha GP1800 Solas Impeller Install and Pump Removal - PWCMuscle Build Series

[@scottrangus4699]

Tip to save a little time: Linkages to the trim and reverse gate have quick release ends so no need to unscrew the fittings on the pump unit. Just slide the sleeves back and pull the cables off the ball fittings. You still have to unscrew the steering linkage though.

[@Pwcmuscle]

Great point

[@deacadeind]

Great video and thank you for taking the time🤘🤘🤘🍺🍺

[@FabazMr]

Thank you very much by fab by fab in the French West Indies

[@fresh3131]

Nice video, Thanks for the update. can you tell me what was the speed after install ?

[@Pwcmuscle]

Thank you! Results will be posted tomorrow on the full build page, but its upper 70s. This impeller is a bit tall for the setup; we are going to continue adding mods to increase power where it'll be better suited for future updates. Here is the link to the full build page: www.pwcextreme.com/t/yamaha-gp1800-build-series-by-pwcmuscle-com/296

[@jeffr1085]

Thanks mate appreciate the video

[@salvatorem740]

What sealant should I use

[@eostrow1963]

What’s the torque?

[@evostigti]

Can I run a solas 13/18 prop on my ski with only an exhaust, waterbox and intake ? Will it be better than the stock prop ? Thanks in advance 🙏🏻

[@Pwcmuscle]

You can, but you'll be banging into the rev limiter on the top end.

[@evostigti]

@@Pwcmuscle I have a solas 13/18 I got from a buddy who sold his ski. Is it better to stay with stock impeller or switch to 13/18 ? Im a fan of acceleration not mostly a top speed guy

[@Pwcmuscle]

@@evostigti Test them both out. That 13/18 should give you superior acceleration, but again, you'll be down a couple MPH on the top end.

[@evostigti]

@@Pwcmuscle thanks bro currently trying to swap the pump out having trouble to pull out the pump after removing all 6 bolts. Any idea how to pull it out ?

[@whittakersexpress8810]

@@Pwcmuscle would you say 13/20 will work good on a 2020 fx for top speed

[@BiLoSellHigh]

Stock or the 13/18 Solas ?

[@Pwcmuscle]

I don't understand the question?

[@marty906]

4:36 Looks like a 13/20

[@tonypinneri2274]

1 3/8" in incorrect. it is a 36mm open end. don't buy wrench you don't need like I did.. just an FYI

[@scottkarwowski1144]

What type of sealant are you using or recommend when putting the pump back together?

[@danielzentz8163]

Was wonder the same thing

[@fhaskell12]

Did you find out? I need to know too

[@kirkm6736]

Joe.....what type of adhesive should be used? Any chance you can name a brand or link to a product? Thanks.

[@tirekicker99887]

Kirk M threebond 1207b is what’s recommended in the factory Yamaha repair manual

[@liftedf-150ford8]

Excellent video! Very detailed.

[@djjunior809]

Thanks you the video Joe! Question though, how can torque the Solas impeller when installing it?

[@Pwcmuscle]

Tighten to hand. These are reverse threaded.

[@k.tanaka1866]

Got the impeller installed but I noticed there is A LOT of water in the GP after running it for just 10 minutes! Any idea what went wrong? kzbin.info/www/bejne/pKLOc414g9usorc

[@Pwcmuscle]

Link for the full build here: www.pwcextreme.com/t/yamaha-gp1800-build-series-by-pwcmuscle-com/296

[@jpassarella73]

Is there any reason why you removed the ball joints from the trim and reverse bucket as opposed to simply removing the spring loaded socket cable ends?

[@Pwcmuscle]

Good point.....just force of habit really; the springs have given me trouble in older skis over the years.

[@senditsillly1423]

Is that prop give better top end than the dual prop. I have stage 2. Also I’m at 138hrs and my clutch is still good, when can I expect to have to replace it? 200hrs?

[@raymondbushey3898]

how did ur solas last

[@Pwcmuscle]

No issues

[@senditsillly1423]

Hey joe what do recommend the lucky 13 pump cone or the Worx pump cone? Thanks.

[@peterodriguez3053]

I have a 2019 fx svho but I see the manifold is like plastic, can I do the same

[@TheYeti308]

Hey Joe ; What pump moves the most GPM .

[@maxjones9139]

Yeah breaking the seal to get the pump out is a major pain.

[@Pwcmuscle]

For sure. Just wait until you have to break loose the impeller for the first time!

[@lukereed1380]

I feel like I’m going to shear the shaft with the amount of force I’m putting on the impeller. There is a lot of torsion/twist in the shaft. I’ve tried heating with a butane torch. Will it eventually release?

[@maxjones9139]

@@lukereed1380 If you have a good bench with a good vice on it it’ll come lose. I used a 6 foot metal fence post as an extension/negotiator. There was a pucker moment thinking surly I’ll f up the shaft but it came off. I got it good n hot too. Ordered a 13/20 from skat trak and the first one showed up with some imperfections. Make sure you give a good look at what you’re installing!

[@christopherlow5320]

Thanks for the video..

[@KMURRAY1841]

Nice job pal much appreciated and awesome videos Joe! I can’t seem to pry off the housing any suggestion? Heat gun?

[@HH-mq9of]

Same problem How did you get it loose

[@dproulx7380]

Joe great video will marine silicone be ok for the pump sealant and with stage 1 plus are titanium retainers needed and is the riva coolant upgrade needed I’m up in northeast water temps rarely get over 68 degrees

[@SlayerHawkX]

Little late here , but no need for retainers/intercooler on stage 1 plus ...I just done a full stage 2..getn retainers tomorrow..yahoo

[@videntemusic2465]

Hi bro I have questions I have waverunner ex sport 2020 I want to change the impela solas I need change the wear ring or not is obligated?

[@Pwcmuscle]

Nope, you do not need to change the wear ring out as well. You can do jsut the impeller. Here is a link: www.pwcmuscle.com/solas-yamaha-concord-144mm-12-20-impeller.html

[@videntemusic2465]

@@Pwcmuscle thanks

[@videntemusic2465]

@@Pwcmuscle my friend for waverunner vx 2022 what inpela I need for buy in you web to

[@djhamidreza]

What’s the difference between dual solas impeller vs this one?

[@Pwcmuscle]

If you have the power to run the dual, it really helps with cavitation

[@cadesaalmann49]

Hey I would like to get into racing but don't know where to look online can u help?

[@Pwcmuscle]

Hi Cade, depends on where you are located. Shoot me a message on PWCExtreme.com and I can send you some specific links. -Joe

[@cadesaalmann49]

PWC Muscle ok thx

[@jameskrivitsky9715]

I saw on another video a tech saying the cap on the impeller slows the performance. He suggested leaving it off. Any input from you as far as results ? Thanks J K

[@maxjones9139]

I heard that also. I’m curious too.