NOTE** Be aware that the throttle body shown in this video has been installed incorrectly. The throttle body should be turned 180 degrees where the electrical cable and servo unit is to the rear (or left if you are looking at it).
@Stiwrb6 жыл бұрын
you are correct.
@seanattwood11703 жыл бұрын
The arrow on the riva ring is supposed to point towards the throttle body
@kennethbrown64974 ай бұрын
He installed the Riva ring with arrow pointing in air flow direction, which is away from throttle body. Two videos I've watched have done this the same exact way, are you saying they did it wrong? To point arrow towards the throttle body means it's pointing away from air flow direction.
@WestCoastWatercraft7 жыл бұрын
Great stuff guys!
@lsvoltvolt97906 жыл бұрын
West Race car golf cat
@paulojimenez56254 жыл бұрын
Will this work on a boat I have a 230sx and it has one on each one of the throttles wonder if it will increase hp?
@strvph643 жыл бұрын
I can say from experience, if you go to this much trouble for the ribbon - replace the garbage stock throttle body mount with a billet 1 piece unit. They fail all the time. Cheap a bulletproof after.
@alecmislin13323 жыл бұрын
Thanks so much dude!!!
@SlayerHawkX4 жыл бұрын
love it..but the parts are WAY over priced..330 for a air intake..wth!....
@Stiwrb6 жыл бұрын
can you remove throttle body without removing intake manifold?
@brockb445211 ай бұрын
So what are negatives/risks of removing the ribbon? Yamaha put it there for a reason, right?
@bambaruz707 жыл бұрын
What's next, a blow off valve installation I hope :) ???
@Steel5xchampS7 жыл бұрын
that ribbon serves more purpose then you think...and the whole "it prevents backfire" is far from its main purpose. Its main purpose is to regulate air flow which is why its in the throttle body in the first place. Serves same purpose as a Mass Air Flow sensor "grid or screen" commonly found on vehicles. Which when said individual was looking for ways to improve fuel economy and add horsepower--giving by throttle response, accel/top end as well as improved engine sound you would simply remove the grid in the throttle body/MAF sensor section of intake. Most times this was done inconjuction with adding upgraded performance filter or full on filter intake kit. The only down side to removing the grid/screen is most vehicles you would have to disconnect battery to reset ecu. But after a few hours or days it the computer would adjust itself back to normal to makeup for increased airflow or it would cause poor running. which is why when you do stuff like this its best to have the PCM/ECM/ECU reprogrammed to allow for the increase in air. Or else your gains will also be seeing losses in other areas
@nickjulian92714 жыл бұрын
It runs off MAP
@clikuk37193 жыл бұрын
Question Will the ECU auto adapt to the air fuel mixture after this install as you will have a leaner mixture now Or will you have to now buy the tuning module to get the right air fuel mixture best to let people know this As a lean mixture is not good
@Pwcmuscle3 жыл бұрын
It "adapts". There is a sensor and it just reads the map according to the sensor's output and the RPMs and throttle position
@clikuk37193 жыл бұрын
@@Pwcmuscle Thanks good to know regards
@bobbyhorton4034 Жыл бұрын
@@Pwcmuscle so there is no need to flash the ECU after removing the ribbon, because it will adapt to the increased air flow? I know on my fuel injected atv, if you didn't add a power commander you would have a lean condition with all that extra air. Just curious what's different from this injection system and computer than the one on my fuel injected Yamaha ATV engine? It would seem that the ecu retune by Dean's or Riva would in conjunction with the ribbon delete,. would wake the engine up a bit because the reflash is where the added fuel comes from that richens up that new air from the ribbon being out
@Pwcmuscle Жыл бұрын
@@bobbyhorton4034 A tune will absolutely wake up the engine, and we highly recommend it. But without the ribbon, you don't get a lean condition because of the way the sensor works with the supercharged yamaha engine
@Pwcmuscle7 жыл бұрын
Performance results for this modification posted up at PWCExtreme.com: www.pwcextreme.com/t/yamaha-gp1800-build-series-by-pwcmuscle-com/296/12
@shkodranpuro4 жыл бұрын
what about the same job in a 2018 gp? thats complete different job..
@ozwiz7 Жыл бұрын
No info on removing the damn fuel injector connectors!
@andrew1975rus Жыл бұрын
Hi How disconnect the fuel rail ?
@LamborghiniV12M5 жыл бұрын
Hey Mr PWC Muscle, Hows that Valve Retainer Video coming along?
@bambaruz707 жыл бұрын
Hello, great videos on the new models very well done! I have a Yamaha FX SHO from 2011 and I am changing the power filters to K&N and I can not find anywhere on the internet where you install the engine breather filter, can you help with a suggestion or a link to a pictographs?Once again, great videos, keep it up!
@Pwcmuscle7 жыл бұрын
We don't have an FX SHO on hand to show you, but here is a Riva's instruction manual for how to install their part. Hope it helps! rivaracing.com/file/2049-RY13040+-+%6011%7E09+FX-SHO+%26+FZR-S+Performance+Power+Filter+Kit.pdf
@kevinaalberts92513 жыл бұрын
@@Pwcmuscle , manual is no longer available.
@slyr13 жыл бұрын
When are you going to install a Yamaha SVHO engine coolant upgrade kit video
@Pwcmuscle3 жыл бұрын
We won't be doing a coolant upgrade video as we've already installed it. Perhaps next year we will switch to a newer SVHO and show this.
@WaterDR-tw8re3 жыл бұрын
The ribbon delete looks like a giant PIA
@gregbeetem62185 жыл бұрын
Am i crazy or did you put the billet sleeve in backwards? Definitely opposite of the paperwork i got with the sleeve
@charlesdecker73795 жыл бұрын
I think he did install it backwards. I'm pretty sure that the arrow is supposed to point TOWARDS the throttle body.
@Nektajnz682 жыл бұрын
I have a GP1800R svho 2020 if I do the ribbon delete will I need to get the ecu mapped to compensate for airflow been told yes and no ...so confused
@Pwcmuscle2 жыл бұрын
Get a tune no matter what...it makes a huge huge difference on this ski.
@Highdrogen3005 жыл бұрын
I installed the riva cold air intake, do you recommend using that smaller filter instead of putting back the hose to the intake ?
@Pwcmuscle5 жыл бұрын
Hey Vic, not quite sure what you mean? The engine breather?
@roscoadventures21943 жыл бұрын
Hi mate I have a gp 1800r Yamaha 2019 how much for a cold air intake kit. And a breather filter kit. Where can I get there's items thanks Rosco.
@Pwcmuscle3 жыл бұрын
Hey man, all your parts are on PWCMuscle.com!
@AchikSarih3 ай бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤
@marcosnazco44386 жыл бұрын
can i delete the air intake all together and not put anything? i recently bought a used fzr and the owner had it without the air intake.
@johnh95076 жыл бұрын
i bought a new 09 fzr and what i did was remove the entire air box and put a 90 degree rubber hose on the front of the supercharger and a small filter at the oil reservoir
@craigblackwood65947 жыл бұрын
Is this mod air intake, Ribbon delete etc legal? Not trying to be smart but don't know if the emission laws apply to watercraft. I would like to do most of these especially the water box delete... Thanks
@Pwcmuscle7 жыл бұрын
The ribbon is not an emissions device, it is to prevent backfire from reaching the engine compartment. You still have the intercooler, supercharger and filter preventing this as well.
@matthewkylelewis6 жыл бұрын
While I know it would be minimal, do these Riva parts also contribute to any weight savings?
@Pwcmuscle6 жыл бұрын
Yes, but as you mentioned minimal. Maybe 3lbs? Complete guess...the stock air box wasn't too heavy on these (compared to say SeaDoo)
@matthewkylelewis6 жыл бұрын
What about exhaust? the stock exhaust looks pretty bulky. I would think between swapping air intake, exhaust, and switching to a lightweight battery there may be a decent drop in weight.
@Pwcmuscle6 жыл бұрын
Stock exhaust sound suppression system has some heft to it. A free flow exhaust eliminates that.
@kontsombos7540 Жыл бұрын
@@matthewkylelewis How about losing some of your extra body fat? That drop in weight will be considered healthy for you and your ski.
@evostigti3 жыл бұрын
is it a same process for a 2018 gp ? I see some people requiring to drill it out..lil confused here. If its a pull and put I would like to do this mod. Thanks in advance!
@Pwcmuscle3 жыл бұрын
They changed after 2017 to a different design. Now you have to drill
@evostigti3 жыл бұрын
@@Pwcmuscle thanks for the quick reply. I appreciate it. Do you sell a filter that connects directly to the supercharger (like macboost) ?
@Pwcmuscle3 жыл бұрын
@@evostigti Not currently but working on one as we speak!
@peterodriguez30535 жыл бұрын
I have a 2019 fx svho and the manifold is like plastic, can I still do this
@Pwcmuscle5 жыл бұрын
It is a different part, but yes!
@peterodriguez30535 жыл бұрын
do you sell it and whats the part number? do you have instructions on how to install@@Pwcmuscle
@mortirius13 жыл бұрын
Fyi the purpose the ribbon serves is as a spark arrestor.
@Pwcmuscle3 жыл бұрын
Correct...but we find it redundant with the intercooler and supercharger, and an easy way to gain a boost in power.
@mortirius13 жыл бұрын
@@Pwcmuscle 40 Riva ring < .59cent 1.5 pvc pipe section. But great video thanks.
@alex1242416 жыл бұрын
Any videos for vxr intake install?
@puchy53893 жыл бұрын
Don’t spend money on vxr. If you speed get a super charger jet ski
@the.mr.nobody3 жыл бұрын
@@puchy5389 dont listen to doucher here. I got a 2013 VXR cheap. Ribbon delete and cold air. I run neck and neck with a stage 2 RXPX260.
@juniemade97123 жыл бұрын
Would this ribbon delete work on the sx190 as well? Thanks
@Pwcmuscle3 жыл бұрын
Which year? If it has the SVHO engine, it should. The question is whether it is a plastic or aluminum intake manifold.
@juniemade97123 жыл бұрын
@@Pwcmuscle 2016 plastic intake. I found that out yesterday having to take it all the way off just to get to a temp sensor. This video helped tremendously by the way! Haha! 👌🏽
@Pwcmuscle3 жыл бұрын
@@juniemade9712 Plastic has a kit, just a little different, still available in the store.
@user-yg4br9ji1n3 жыл бұрын
Is Ron Jeramy your father? Lolololol
@quadit3217 жыл бұрын
What's the reason for the ribbon ? seems like it shouldn't even be there .. also by removing the air box is it easier to suck water in to motor now ?
@Pwcmuscle7 жыл бұрын
The ribbon is there to help prevent a backfire from reaching open air. The air filter, supercharger, and intercooler will all do this as well. The air filter is mounted up high, so it'd be pretty hard to suck up water with it
@X862go6 жыл бұрын
You would have to have 20 in of water in the hull before that happens.
@Chris-oc4eo5 жыл бұрын
So backfires can now damage your machine doesnt sound good for long term use
@adventurer41882 жыл бұрын
How much %up gain with ribbon delete without vs with intake ?
@Pwcmuscle2 жыл бұрын
Didn't test those back to back, but Riva claims as much as 1psi boost from removing it.
@adventurer41882 жыл бұрын
@@Pwcmuscle thanks looking forward to the results with tune, so my guess is that equates to 3-4 horsepower on top of the tune, ribbon delete?
@adventurer41882 жыл бұрын
@@Pwcmuscle or less, just want to know how much power I’m getting before I order, however small or great.
@Pwcmuscle2 жыл бұрын
@@adventurer4188 Hard to say exactly, but if it is a 1psi increase it'd be closer to 10.
@skiman73974 жыл бұрын
Hi i have a 2019 fx svho and im fitting the tial bov i want to tap the manifold instead of running from the map , whats the best way to do this and whereabouts on the manifold will be best placement for the tap
@kevinaalberts92513 жыл бұрын
hmmm cold air intake. but your putting it in a place that gives off heat!!! where you getting this so called cold air from!!??? too soon?
@Pwcmuscle3 жыл бұрын
It's pulling air from the front compartment that also has air vents. For the record, we showed a measurable increase in performance with this kit.
@jarrettlabate55953 жыл бұрын
What is the purpose of that OEM ribbon??
@Pwcmuscle3 жыл бұрын
It is a major restriction to air flow
@jarrettlabate55953 жыл бұрын
I understand it's a restriction but why did Yamaha put that there what is the original purpose
@Pwcmuscle3 жыл бұрын
@@jarrettlabate5595 it is a flame arrestor
@difecigr97232 жыл бұрын
@@Pwcmuscle good point, bit more acceleration or more safety 🤔
@sharynbicknell11077 жыл бұрын
Been riding Seadoo's and Yamaha for 20 plus fun years. Leave it factory, unless you have extra money to spend or you are a waverunner mechanic.
@Pwcmuscle7 жыл бұрын
Extra money to spend to go faster.. precisely why we make these videos.
@X862go6 жыл бұрын
Do how well did this upgrade help you I have heard good things about removing the ribbon.
@Pwcmuscle6 жыл бұрын
Worked well...check the numbers. Details posted here: www.pwcextreme.com/t/yamaha-gp1800-build-series-by-pwcmuscle-com/296/12
@The_Brew_Dog4 жыл бұрын
How many hours did it take to preform the job approximately?
@sandorkruise7660 Жыл бұрын
i just finished , DAMN that was 3 years!
@daryllcarrodeguas79106 жыл бұрын
Hi! can this mods be done on the yamaha boats. Example SX 192
@johnh95076 жыл бұрын
i would put some towels on the motor so nothing gets scratched up when using it as a table for the intake
@kontikinomads67505 жыл бұрын
So have you blown yourself up yet from removing the ribbon
@Pwcmuscle5 жыл бұрын
Nope. Flame would have to get past an intercooler AND turbocharger compressor to reach the air intake, and then the air filter is there to prevent it from reaching the hull. Still alive and well!