Thanks so much for the video. Just before putting my boat away for the winter, the motor ( an 1989. 70HP Evinrude) stayed in the raised position and would do nothing as far as tilting goes, no sound, nothing. I found the disconnect plug, reseated it, now it's fine. I applied some liquid to make better contact and reseated the plug a few times, and it seems ok. Thanks again.
@getgoodusa2 жыл бұрын
Huge help. Just inherited a 1976 evinrude 70hp and trim/tilt does nothing. This is a great place for me to start thanks again
@garyhahn14236 жыл бұрын
Great job Brandon! Very well done, well explained video. Getting ready to add a tilt / trim unit to my 91 OMC Quiet Rider 115.....your video has been extremely helpful! Thanks
@dmcoulter5649 Жыл бұрын
Amazingly clear and concise explanation. Pleasantly void of most of the YT self promoting garbage
@dylweeed3 жыл бұрын
I signed in just to like this video. Great support and walkthrough!
@gmatos1232 жыл бұрын
Great video explanation. Can be applied to almost any big outboard I’ve seen
@MrPanama496 жыл бұрын
You may have solved a problem I've had in hooking up an add-on T&T unit on my '85 J70. Only thing I could suggest for us DUMMIES is to show the ends of the wires as you hook them up so we can see if they match what we have. Thanks for a helpful vid.
@bigq78568 ай бұрын
So on mine I have a lever underneath the motor that if I move it up & down I can see the gauge go up and down but it doesn’t move when I’m actually using the button any thoughts would help.
@ILIKE2FIXSTUFF3 жыл бұрын
My boat works everything but didn't come with a trim gauge for some reason. I'm used to checking it and stuff. I know I can turn and look at the engine but I was wondering if I could add the gauge. Maybe from the controller to the gauge?
@michaelbarnes7538 Жыл бұрын
I've seen you use a push button to start johnson outboards ...how do I wire one for myself please ..
@chuckallen97787 ай бұрын
Excellent vid. Helped me a lot.
@taylerrichards73332 жыл бұрын
The blue cables are connected to the trim stop to shut off the trim motor and stop the engine being tilted too high
@masonzick12872 жыл бұрын
Where can I buy one of those "Harness" wires for the three-prong cord that comes from the controller?
@littlebitofeverything652 Жыл бұрын
Awesome video you made me understand huw everything sinks together thank you. I have a 1999 Evinrude 70 on my 2000 crestliner 1700. My trim works on the switch in the front and back at the motor, my problem is my trim gage is stuck in up position could be because it sat for long time in the barn. I want to get that gage working again but I can't locate the darn sending unit with lever on. Any advice ?
@michaelthorpe95604 жыл бұрын
hi can you please help me,, I have an old 1993 Johnson 140 hp V4 engine, that is giving me some grief ,, can you give me some pointer's on what to have a look for as to why my tachometer gauge only work's when the engine it upright, but the moment you start to trim up or down, the gauge drops off and you lose the rpm reading?,, I am thinking its a brake in the harness loom some were?,, as the rpm gauge dose work,, were on the engine dose the rev gauge hook up to?,, and what color would the wire's be so that I can try and track them back up the loom to find the broken wire, and hopefully fix it and get my rev counter working at all stages of engine trim!,, this rpm gauge is driving me nut's trying to get it working now,, so how long can I keep taking the head ache tablets before they do me in?,, thanks for any help you can give me, Mike
@BlueOakTree2 ай бұрын
Awesome video thanks
@SuperKatama3 жыл бұрын
Great video Brandon, thanks! I'm installing new on 88, 88 hp, Johnson. Bought all the parts. I'm confused about where terminal block is on motor and trim sender unit? Also, wire diagram shows wires go back to ignition switch in addition to the three wire on controller for switch? Any help is appreciated. Thanks
@BrandonsGarage3 жыл бұрын
Trim relay box is on the back of the engine, between the heads. You'll see the 2 stubs sticking out where the box will screw on. 3 wire trim switch can be seen here: kzbin.info/www/bejne/mna9fJmwjLCKgas
@SuperKatama3 жыл бұрын
@@BrandonsGarage Thanks again. I figured out the placement and no need for a sender unit without a guage. Still confused my switch has three wires, blue, green and red blue dashes. Trim motor has blue and green. I presume the red w blue dash is the ignition switch wire back to the relay box? Great channel, thanks for the tips.
@inocencioocampo79635 жыл бұрын
Brandon. I been working on my t&t motor. You said it on the video, just to clarify, it is ok to go straight with the power or positive from the battery to the relay box?
@tracyherald87044 жыл бұрын
Hi Brandon i replaced my 3-wire to a 2-wire trim tilt motor. I bought the conversion harness but am clueless on what to do with the two smaller wires (green/white and blue/white). I wish i could send you a picture to show what I’m talking about.
@BrandonsGarage4 жыл бұрын
the small green and blue wires goto the trim switch Its a 3 prong switch. red batter + in the middle, then im pretty sure blue goes on the bottom terminal, green on top.
@tracyherald87044 жыл бұрын
Brandon's Garage thanks so much for getting back to me so fast. I love your channel. Extremely helpful for guys like myself. I’ll just need to splice then in “before” the connector in the motor then?
@mississippipoboit10746 жыл бұрын
Can u do a video explaining the 3wire system
@rodneyhatcher18583 жыл бұрын
I have a 3 wire and need help🙏🙏
@mississippipoboit10743 жыл бұрын
@@rodneyhatcher1858 from my understanding ground n the middle n wen use the switch up n down it sends power threw one side n wen u move switch other way it does the opposite
@johnmullins10345 ай бұрын
Cant get my trim tikt gauge to work old on did but new one wont on 120 evenrude
@kooter007 жыл бұрын
Hello Brandon, I have a 1989 90 HP Evinrude. I have 3 wires coming from the tilt sender (white, black and green). I followed them up into the motor and the white and black go into the power block but the green wire is just sitting there not attached to anything. If it helps it's got a ring terminal on the end of it. Where should it be attached to on the motor?
@rodneyhatcher18583 жыл бұрын
I have a 88 evenrude xp150 and I have a 76 evenrude 200 can I take the wiring off the 150 and use on the 200 I need help
@dignon383 жыл бұрын
I need the connector (3 pin) from the wiring harness to the control box. Anyone know where I can get that? I’ve been searching like mad to get the right part. 1983 Evinrude 75
@donaldprice418310 ай бұрын
will the tilt and trim on a 150 horse fit a 40 horsepower Evinrude
@BrandonsGarage10 ай бұрын
Nope! Unless youre talking about stuff from the mid 70's, then yes; with some different brackets. If you're talking about 1980s and newer, gosh no.
@donaldprice418310 ай бұрын
thank you@@BrandonsGarage
@brandonbentz89954 жыл бұрын
Where does the trim sending wire come out of the box mounted on the motor
@GreggAdventure2 жыл бұрын
tries to pause and see back of gauge. Kept missing.
@JARatelle4 жыл бұрын
My trim gauge is stuck on full trim. When I put the sender to ground for a fraction of a second the trim gauge goes to the bottom. Not sure what's going on.
@JARatelle4 жыл бұрын
I should mention that this is definately the best video I found on this subject. Thanks!
@eliasbendeck46706 жыл бұрын
Brandon, I have a 2000 Johnson and I have been trying to figure out why my tilt will only go down and not up. I tested both switches at throttle and engine, both work down but the up button I don't hear the motor. I changed the relays and no luck. I cant figure out where the limit switch is located and was hoping you could help pinpoint where I could find a diagram indicating the location. Now that's assuming that the limit switch is the issue. Any suggestions? before I bring to boat repair shop... Thanks, George
@BrandonsGarage6 жыл бұрын
Its on the tilt tube. Not all engines have a limit switch by the way. Does the motor run when you up? or does nothing happen?
@donron46254 жыл бұрын
Hello brandon. I know this is an old video. Iwas wondering if you could help w any tips. I have a similar issue on my 96 225 oceanrunner . My tilt pretty much only goes down. I added fluid and bought new relays. Nothing. Trim motor makes noise while going down but its completely dead when i press up on switch. Thnx in advance .
@rodneyhatcher18583 жыл бұрын
How do u hookup a 3 wire trim on my 76 evinrude 200
@TruePatriot59 Жыл бұрын
Where does the power trim tilt limit switch mount?
@BrandonsGarage Жыл бұрын
The few models that do have a limit switch, they are located on the tilt tube. This style of trim has no limit switch.
@rodneyhatcher18583 жыл бұрын
Do I need 2 fuel pumps on a 76 evenrude 200
@glen3993 Жыл бұрын
you seem to be Guessing about ALL of what you're doing with this engine, you really need to know all about the engine your working on like the Year of it and the Model, Codes on the tag located on the left mounting bracket
@BrandonsGarage Жыл бұрын
Oh gotcha, I'll try to figure out how to look that up.
@cajunroadwarrior3 жыл бұрын
What is confusing the hell out of me is I have a motor with three wires. One ground and two hots. Connecting either one will run the motor in opposite directions. I haven't found a relay set that will work with this motor. Everything I have bought on eBay or Amazon doesn't work. I connect the green and blue to the painted connections shown on the relay yet the motor barely turns and the wires get hot. When I connect the motor directly to the battery it runs fine.
@BrandonsGarage3 жыл бұрын
your motor is working properly, the problem is your relay setup; it is supplying an additional ground signal, when it shouldnt be for a 3 wire motor. Your ebay/amazon harness can work: in the middle of each relay you should have a large ground wire, thqt needs to be removed from both relay sockets (cut, or terminal removed) and itll work fine l. there are 2 ground wires going to each relay, it needs the smaller one, usually on the left of the larger. Middle needs to go, left/right stays.
@cajunroadwarrior3 жыл бұрын
@@BrandonsGarage this is actually a single large relay. It has four terminals and three control wires. I tried a pair of relays from mMercruiser and they didn't work either. I was thinking of trying a pair of starter relays. What confused me about the Mercruiser relays is they are wired like a regular relay. It makes no sense that they would be back feeding when I'm hooking all the grounds up. The positive circuits should be separate from the grounds.
@cajunroadwarrior3 жыл бұрын
@@BrandonsGarage I fixed it. That third ground wire confused me.
@joeyurban51692 жыл бұрын
@@BrandonsGarage shot in the dark here but my buddy has a 2017 pontoon with a 90hp 4 stroke suzuki. It has power trim on the motor and controller. He doesn't have a gauge and would like to add one. How difficult would it be to add one?
@rodneyhatcher18582 жыл бұрын
How did u fix it I'm having the same problem need help send a picture of ur setup if u can
@gunnersellman56256 жыл бұрын
where did you get the relay box?
@BrandonsGarage6 жыл бұрын
All over ebay: rover.ebay.com/rover/1/711-53200-19255-0/1?icep_ff3=9&pub=5575301501&toolid=10001&campid=5338087097&customid=&icep_uq=evinrude+trim+relay&icep_sellerId=&icep_ex_kw=&icep_sortBy=12&icep_catId=&icep_minPrice=&icep_maxPrice=&ipn=psmain&icep_vectorid=229466&kwid=902099&mtid=824&kw=lg ...just start looking, and pic out what you're after.
@jaysoutdoors7237 жыл бұрын
Does the 81 90hp v4 work the same way
@BrandonsGarage7 жыл бұрын
Not quite- Originally that engine had a 3-wire trim motor. Which used a whole different relay/electrical box. If you have a newer 2-wire trim motor on it, you can install an external controller and use it just fine. If you still have a 3 wire setup, you can get a 3 wire relay controller on ebay too.
@jaysoutdoors7237 жыл бұрын
Brandon's Garage what is an external controller I have a 2 wire
@jaysoutdoors7237 жыл бұрын
Brandon's Garage I can send you some pics of what I have going on I've been looking all over web but can't find anything
@jaysoutdoors7237 жыл бұрын
Brandon's Garage sent it del it
@liviofazi4017 Жыл бұрын
Can you not just hook up an external setup....tilt motor switch battery.....not sure why it's so convoluted and needs to go to motor housing.....I know nothing when it comes to this