QS138 90H Swapped SSR125 Is Back For A Controller Swap! Fardriver ND72450

Рет қаралды 1,900

5 ай бұрын

help support the channel by joining my patreon! - patreon.com/Emx_Brandon?...
BombMoto Electric Dirtbikes group - m. groups/6501191...
Mototec Electric Pitbikes Group - groups/10831...
Dm/follow me on instagram - / emxbrandon
music by my brother check out his channel on youtube - / theaustinely
if you like video games check him out on twitch too! - / waifuandhusbando
filmed on my insta360 one rs/galaxy note 20
Bikes-
72v mototec qs165
48v razor rsf650 etm kit
72v bombmoto b1
09 ktm 105xc

Пікірлер: 30

@B1shops 4 ай бұрын

I was planning to use that setup for a go kart. Is it not more powerful than that? I would like to drift with that thing. And able to go like 80km/h at least.

@EmxBrandon 4 ай бұрын

Much more powerful, but it's limited by the battery and controller. The 90h isn't the best setup for a go cart due to ypud have to run very tall gearing since you have to run a small rear sprocket. So getting the torque off the line or to initiate a drift at lower speeds is gonna be difficult. I'd recommend the qs138 90h v3 with gear reduction.

@B1shops 4 ай бұрын

@@EmxBrandon hmm thanks for the answer. How to order it with gear reduction? How much redution?

@B1shops 4 ай бұрын

I actually saw some called "internal reduction gears" 1:2.35 Is it that 1?

@paulawestcott7228 5 ай бұрын

Total Electrification power project however It needs the battery box and motor moiunts corners and some edges rounded and smoothed out for safety, and flow of the design. Love your videos!

@EmxBrandon 5 ай бұрын

Thank you!

@morganmcdougall4259 5 ай бұрын

Very tidy bro 😊🤘🏼 That would be wild throwing a wheelie on and sparking up the scrape bar 🔥

@EmxBrandon 5 ай бұрын

I'm definitely too scared to wheelie deep enough to touch the scrape bar 🤣

@voltmasterp8470 5 ай бұрын

Look at you go !!

@EmxBrandon 5 ай бұрын

🤘🏻🤘🏻🤘🏻

@franklabs3766 5 ай бұрын

Hey man, watched many of your videos just today, you told us that you will do a video on the CT-22's display wiring or any general display. Off the box from china, nothing really fit. It needs to be rewired. If you have any tip or if you know someone who did a video already. thank you!

@EmxBrandon 5 ай бұрын

I've only done a wiring video for the dkd. I'm sure there's some wiring vids for the ct-22 or you can fund the wire diagram for the ct-22 on siaecosys website!

@andyredvolvo9434 3 ай бұрын

👀👌🏴󠁧󠁢󠁥󠁮󠁧󠁿what sprockets did u use on the motor iv just picked up the same qs 138 yesterday

@EmxBrandon 3 ай бұрын

We couldn't find ant 420 sprockets with the correct 20mm spline cut so we just used to stock 15t 428 sprocket and had a 428 custom rear made. It's a 20mm shaft but the spline spacing is the same as the 17mm shaft. And all the 20mm spline you find on amazon/ebay are all the incorrect pattern. But I do believe qs makes different tooth count now down to like 11t but all 428.

@PizzaCologne3 5 ай бұрын

🍻🍻

@EmxBrandon 5 ай бұрын

🤘🏻🤜🤛

@666.32 Ай бұрын

This would work good in stock surron stock batery?

@EmxBrandon Ай бұрын

The 72450? You can definitely run it but you won't really see much more performance without a higher output battery

@noce1071 5 ай бұрын

I absolutely want one . How many miles does it get per charge.

@EmxBrandon 5 ай бұрын

It's awesome! It's got a 40ah so if I was keeping it chill and riding the speed limit (35-40mph around here) I'm sure I could get over 30-35 miles!

@papawyatt5743 4 ай бұрын

Where did you get that Stunt bar

@EmxBrandon 4 ай бұрын

It's just angle iron welded to the subframe. Someone else did that, I just mounted the brackets for the 12 bar pegs and made the brace to go inbetween. All the fabrication is custom on this bike and nothing you can buy pre made.