When you come to a corner, raise your chisel so it is perpendicular to the part and then scribe the next line. This will stop the panel line corners from getting rounded like yours ended up.
@TheMobileSuitHangar2 жыл бұрын
Yow! I appreciate the feedback, man! Thank you for this tip. 🙏🙏
@symnox78343 жыл бұрын
Clever technique for the "blueprint" of the Panel Line. Good tutorial. :)
@TheMobileSuitHangar3 жыл бұрын
Thanks, man! 🙏🙏
@Shokkur2 жыл бұрын
A guitar pick is a great part separator. Durable, thin, doesn’t scratch, and as cheap as it gets.
@TheMobileSuitHangar2 жыл бұрын
I saw a gunpla tip video mentioning that. But now, I got a proper parts separator 😅
@GabDamn4 жыл бұрын
Yo! Those are some sicc panel scribing! Looks like it's time to get out my comfort zone and try this! Great vid!
@TheMobileSuitHangar4 жыл бұрын
Hope this helps for our IBO build-off LOL
@chasinthroughthedecade4 жыл бұрын
Cool! Now I can turn seam lines into panel lines! As for me, though, I have a Tamiya scriber and a Dymo tape which I got from National Bookstore.
@TheMobileSuitHangar4 жыл бұрын
I have the dymo tape. Unfortunately it kinda dislodges quickly :/
@chasinthroughthedecade4 жыл бұрын
@@TheMobileSuitHangar Uh oh. But yeah, I saw that was the case. :( So I guess I just have to try holding it down while scribing then?
@TheMobileSuitHangar4 жыл бұрын
Yeah :/ and you really have to give your first 3 scribes reaaaaally light strokes.
@JARVISX4 жыл бұрын
BACK AT IT AGAIN! Planning to scribe tooo for my first custom gunpla! hehe
@TheMobileSuitHangar4 жыл бұрын
It's kind of scary at first. Just prepare some putty if you have some if you need to correct your errors. But yeah it's pretty fun 😁
@Guthem4 жыл бұрын
A great tutorial! Thanks from Brazil, man!
@TheMobileSuitHangar4 жыл бұрын
Thanks for your support as always, man! 😁👊👊
@kikomantv20184 жыл бұрын
Sweet! Great content very informative. And has very clean audio good job!
@TheMobileSuitHangar4 жыл бұрын
Thanks, brother! 😎👊👊👊
@XNT-Shiyosa922X3 жыл бұрын
Thanks dude. Very easy to understand. And now i just have to buy hobby chisels and im good to go. Im building PG Unicorn and PG Banshee btw.
@TheMobileSuitHangar3 жыл бұрын
Glad to be of help! 😁😁
@rubenramos59873 жыл бұрын
Love this video. Definetly got to try on the next kit.
@TheMobileSuitHangar3 жыл бұрын
Thanks, man! 🙏🙏👊👊😁😁
@jordanhurley13142 жыл бұрын
This was a great video! Super helpful in showing how to pick where to put your lines.
@TheMobileSuitHangar2 жыл бұрын
Thank you!!
@jomarieliwanag84764 жыл бұрын
We use the same chisel i got from an online shop. Nice vid by the way
@TheMobileSuitHangar4 жыл бұрын
Hey good to know! 😁 they're not bad at all. 😊 Thanks for watching the video, man! 😁
@stephanmatuteschulz62093 жыл бұрын
Just happened to have the same kit half built and was looking for scribing advice!! Salamat
@TheMobileSuitHangar3 жыл бұрын
Thanks, man! 🙏🙏
@vincentvillarama75884 жыл бұрын
Thank you so much for this info very easy to follow
@TheMobileSuitHangar4 жыл бұрын
Wow! I hope it really helped! 😁
@redwardranger70343 жыл бұрын
I my God I knew that compass would help. Anyways, awesome and helpful video as always. I'm gonna practice on the spare HG Barbatos shoulder I have as I don't wanna mess Hyaku Shiki
@TheMobileSuitHangar3 жыл бұрын
Thanks, man! 😅 Yes, practice on scrap parts first 😁
@redwardranger70343 жыл бұрын
@@TheMobileSuitHangar Plus, Hyaku Shiki's gold can be annoying at times
@DeDoGunpla4 жыл бұрын
nice tutorial mate very informative... more tuts pls.. =)
@TheMobileSuitHangar4 жыл бұрын
Sure, man! Haha I'll have to improve my modelling skills for that. 😁
@thehobbyistartist24753 жыл бұрын
This is helpful, I'm starting a vlog about Gunpla Custom Painting, scribing needs more Patience
@TheMobileSuitHangar2 жыл бұрын
It does! I'm still actually improving and correcting my mistakes
@davidhovik71763 жыл бұрын
What a perfect video thank you so much!
@TheMobileSuitHangar3 жыл бұрын
Glad it was helpful! :D Thank you for watching!
@davidhovik71763 жыл бұрын
@@TheMobileSuitHangar You're welcome.
@EKsDesk4 жыл бұрын
Thanks for this bro, i badly need this 👌
@TheMobileSuitHangar4 жыл бұрын
Go go go 😁😁
@charaznable53563 жыл бұрын
can you make a video on how to make scribing patterns? what the thought process is, rules, etc.
@TheMobileSuitHangar3 жыл бұрын
I'll try to make one 😅 I think I need to buy more scribers first
@kyrios-gn2 жыл бұрын
I like this idea
@TheMobileSuitHangar2 жыл бұрын
Thank youu!!!
@garethmurphy82353 жыл бұрын
Need some input please. I am starting to get more into scribing my kits and I have good equipment. Dspiae Push Broach with clamp handle. The issue I am having is that after scribing the lines look chewed up and choppy as hell. All the scribes are within the line and follow the pattern perfectly, however, the lines are looking really uneven especially along the edges.. I don't know if maybe I am using a broach that is too thick or too thin. Maybe all the inconsistency will go away after priming but I can keep getting these results and continuing. Any help is greatly appreciated?????
@TheMobileSuitHangar3 жыл бұрын
I have not used the DSPIAE push broach or anything like that so I could give a fair assessment :/ One thing I've learned from practicing more parts to scribe is that you really have to start with really light strokes. Even at least 20 light strokes. It's going to be enough for you to at least help whatever you're using to scirbe to really get locked into the scribing pattern. I hope I'm making sense 😅
@garethmurphy82353 жыл бұрын
@@TheMobileSuitHangar yea I think you are.. Like more even strokes and not with so much pressure??
@TheMobileSuitHangar3 жыл бұрын
Yes! More strokes and slightly increasing the pressure on the strokes
@kmrl59823 жыл бұрын
If you get good enough with scribing you can make a hg look like a rg
@MazingerZX3 жыл бұрын
Thank you for the video! You seem to use only pointy part of the chisel and not the flat .2mm width part? Do you risk damage to the chisel doing it especially on a smaller width chisel?
@TheMobileSuitHangar3 жыл бұрын
Not really, i slightly adjust the angle of the chisel to the flatter part as I add strokes so the lines would be wider 😁
@ilightstv114184 жыл бұрын
thanks for sharing sir!
@TheMobileSuitHangar4 жыл бұрын
And thanks for dropping by to watch, brother! 😎
@kizen666411 ай бұрын
Ive never seen anyone do that technique you used to draw the panel lines. Where you made and X and used the points to make the lines. Is there a name for that?
@TheMobileSuitHangar11 ай бұрын
I actually don't have a name for it 😅 Also, some of the techniques I used here need some corrections. I'll try to upload a new one with the correct techniques
@darylconanan99882 жыл бұрын
thank you
@michaelrodas-arista35663 жыл бұрын
So when you scribe do you put the tape over the line or do you put the edge of tape by the line? Also once the tape is place do you scribe over the tape or on the edge of the tape?
@TheMobileSuitHangar3 жыл бұрын
Hmmm... Well, I lay the scribing tapes one at a time and they don't overlap. Then, I scribe by the edge of the tape. I hope that answers the question 😅
@michaelrodas-arista35663 жыл бұрын
@@TheMobileSuitHangar Yes that was actually helpful!!!! Thanks alot !!!
@neilpatrickisaac37434 жыл бұрын
Great tutorial! May I ask where did you buy the guide tape and how much is it (I'm also from the Philippines)?
@TheMobileSuitHangar4 жыл бұрын
Thanks, man! Pre-ordered it from Blue Brick shop 😁 check em out and get yours 😆
@kidsponjay57424 жыл бұрын
Nice video very informative for newbies, thanka bro, quick question, what can u suggest i use for buffering? an alternative sort hahaha!
@TheMobileSuitHangar4 жыл бұрын
Yooww! You can use the sunshine nail buffer you can buy from cosmetic shops 😁😁 Or, what I currently use, the nano glass file. It's really cheap. I'll have to create a video for it 😁
@kidsponjay57424 жыл бұрын
@@TheMobileSuitHangar thanks sir, found it in shopee.. excited to try it soon, thank you! hope you have make a video about decals and how to keep them in the gunpla and avoid peeling 😁
@HDoroteo4 жыл бұрын
Lodi!!!
@TheMobileSuitHangar4 жыл бұрын
Ahaha support local! 😆
@FighterDoken2 жыл бұрын
Looks like you're using your chisels sideways. That's why your corners look rounded and not straight!
@TheMobileSuitHangar2 жыл бұрын
Yeah. My bad, I tried correcting my technique now. Thanks for the feedback 🙏
@FighterDoken2 жыл бұрын
@@TheMobileSuitHangar Of course! We're all here to learn :)
@rks25thegreat4 жыл бұрын
Nice bro!
@TheMobileSuitHangar4 жыл бұрын
Thanks, bruhh 😁😁👊👊
@charaznable53563 жыл бұрын
i use my guitar pick for separating xD
@ree5724 жыл бұрын
Suggest lang lodi, palagay ng links (if available) ng mga items na nasa vid, or alternatives we can use. Thank you!
@TheMobileSuitHangar4 жыл бұрын
Sure man! Thanks for the feedback 😁😁 will edit the description
@ree5724 жыл бұрын
@@TheMobileSuitHangar yes! Been wanting to customize dati pa. At least d2 pinoy tapos local yung items tapos madali maintindihan. 👌
@TheMobileSuitHangar4 жыл бұрын
@@ree572 yay 😁 updated na yung description. :) though yung sa tape, wala pa ko link from Blue Brick Shop 😅
@ree5724 жыл бұрын
@@TheMobileSuitHangar nice! Thanks! Hanap aq makapal na tape tapos tirahin q tthongli q d2 for practice. 😁
@innocentdevl94996 ай бұрын
pwede kaya 800 grit then 2000 grit tapos buff?
@TheMobileSuitHangar5 ай бұрын
Hmmm I wouldn't skip 1000 grit if that's the case
@hermenmoreno67033 жыл бұрын
Where can I get the tape
@TheMobileSuitHangar3 жыл бұрын
If you're from the Philippines, you may want to try www.hobbyalley.biz :)
@royalpotatoes4 жыл бұрын
bro where did you buy the scribbing tapeee?? O_O
@TheMobileSuitHangar4 жыл бұрын
Blue Brick Shop 😁😁 I think they're still in the preorder phase
@royalpotatoes4 жыл бұрын
@@TheMobileSuitHangar ohh okay i'm also planning on doing some scribbing haha! thaanks for the vid. helps a lot. :D
@TheMobileSuitHangar4 жыл бұрын
Glad to be of help as always 😎😎
@aejobalcasabas953 Жыл бұрын
Is it ok to use xacto?
@TheMobileSuitHangar Жыл бұрын
I wouldn't recommend it. You really have to use proper scribing tools
@aejobalcasabas953 Жыл бұрын
@@TheMobileSuitHangar thank you 🤟🏼
@aejobalcasabas953 Жыл бұрын
@@TheMobileSuitHangar kabayan! 😄 Pano kung xacto tapos sundan ng compass hehe. Ok lang kaya?
@TheMobileSuitHangar Жыл бұрын
@@aejobalcasabas953 You can try but I really wouldn't recommend it LOL You'll get crooked lines
@jakezellealfeche72614 жыл бұрын
Sir mali po yung way ng pag tape ang ing position ng scriber :(
@TheMobileSuitHangar4 жыл бұрын
Ohh noooo :( my bad. How should I apply the tapes and scribe? :/ Thank you for pointing it out, though 😅
@derirujeiku4 жыл бұрын
No worries sir..mdyo na alarm lang po ako kasi kawawa naman ung ibang modeler na gagaya :) Eto sir mgnda tutorial nya and mdami din po iba available sa net na proper use of chisels and guide tape kzbin.info/www/bejne/pmfUaKiblqljetE
@TheMobileSuitHangar4 жыл бұрын
Gotcha. Will check it out. Thank you 😊
@knuckles77904 жыл бұрын
I used a box cutter.
@TheMobileSuitHangar4 жыл бұрын
Woah but isn't that too thin? 🤔
@knuckles77904 жыл бұрын
@@TheMobileSuitHangar I got mine from Home Depot and it's pretty thick.
@TheMobileSuitHangar4 жыл бұрын
Ohhh that's a pretty neat alternative.
@ree-dv5ir4 жыл бұрын
epic
@TheMobileSuitHangar4 жыл бұрын
Thanks, bruhh
@rommelcabasag4 жыл бұрын
i never use a scribing tape...when i scribe...it just me...hehehe
@TheMobileSuitHangar4 жыл бұрын
You then, are a true master of micro dexterity LOL. My hands are ugghh.
@rommelcabasag4 жыл бұрын
because of lacking in tools...i do my own way....using only what i have in the house..just being creative...
@TheMobileSuitHangar4 жыл бұрын
@@rommelcabasag dang brooo... How do you create such straight panel lines?