Ram 45 micromotor repair part 1

Take down and parts identity.
www.lightelegan...

[@davevankerr]

Great video Ed. I'd love to see one where you change the bearings.

[@kpvillester]

Thank you so much for your instructions !!

[@EdPitts1933]

You're welcome

[@djomlastic]

Saeshin strong 90n micromotor is very similar. Thanks, this helped me a lot.

[@hereshmehrzad8231]

thank you sir i repair my saeshin micromotor with your demonstration and advice

[@EdPitts1933]

I'm Glad it helped.

[@Coyote973]

Thank you, very helpful video. When I pulled out the rotor from casing, the shims stuck on magnets. I am not able to determine the correct position of them. The only exploded view I have seen so far, is the one you have it. Can you upload it somewhere, since the link in the description is broken. Thanks.

[@EdPitts1933]

Thanks, glad you like it.

[@jayc3110]

Thank you for that very clear and helpful video.. your disassembly instructions helped me clear out a stuck burr! That solves one problem. The handpiece I have seems to be running fine now. But I have another problem with the control unit also. The motor runs only at one speed oh, and I don't know what that is. The control knob does not change speeds at all. Have you had a problem similar to that? How do I get my speed control back? Have you ever had a problem with the control box itself and do you have any experience with fixing the speed control? Any suggestions from you will be very helpful, thank you again.

[@jaimefilho4959]

I have had this problem on Marathon 3. It's a transistor failure inside the control box, caused by an input voltage problem. Replace the transistor should be resolve it.

[@jayc3110]

@@jaimefilho4959 Thank you for your response...

[@longdriver2]

Ed, nice instructional video. Very helpful. Where did you get the parts list? Thanks

[@naveenbadri2081]

❤️ from India

[@kpvillester]

Where can I find the diagram of the hand piece parts list ??

[@EdPitts1933]

For anyone, once you have taken the unit apart, changing the bearings is simple. just slide the old one off and the new one on.

[@VioletIndigo3]

I don't know how to take the c clip off.

[@laumcr99]

Muchas gracias muy útil

[@iwin4985]

Where could I find a COLLET CHUCK or Wrench to remove the collet? I can't find it at Patterson or Rams website.

[@ramproductsmicromotors8867]

Common spare parts are listed on www.ramprodinc.com website and available to order as well as all parts needed

[@marcelosantosdacosta]

Olá vc saberia me dizer estou com uma caixa de controle da caneta ela só funciona em alta

[@rwolk8483]

HEllo Ed, How to you remove & replace bearings on both sides armature?

[@user-xz9du1pp3r]

سلام ممكن شرح اسباب عطل البيرنجات حق ميكرومتور ماراوثون

[@eyamnottier3411]

Can anybody ad a link to that parts diagram the link here is in Estonian ....and been able to find the right link.

[@hannekebosselaar-pater2624]

My engine burned I think.... Van In fix it?

[@vijaybalnathkhaire5432]

I'm looking for portable micromotor with lethinium battery

[@paularodriguez2352]

qué es lo primero que saca?

[@mohdasifasifkhan9889]

Hello sir please what us reason heating problem

[@leokadiaigrzegorzfiuczek5934]

hello, did you have diagram of voltage regulator?

[@EdPitts1933]

Grzegorz Fiuczek no. Sorry I do not have wiring diagram

[@jawedzia1024]

I am jawed from karachi Pakistan I am fully repairing and 50`000 rpm waindar call 0093142176669

[@bouhadjamoh2970]

would you like to send me the exploded marathon schemac 35 000 rpm so i can order the different parts by reference.thanks

[@smarzouk82]

front armature bearing won't come off any suggestions?

[@EdPitts1933]

Penetrating oil?

[@AFishTale]

Can you share where you purchased the bearings. Ram says they won't sell them. They said to sent them the hand piece.

[@EdPitts1933]

I bought mine from Ram Products. I don't understand why they would not sell to you.

[@davevankerr]

you can buy them at ldental.com too.

[@EdPitts1933]

Thanks Dave, good info.

[@davevankerr]

Hi Ed. I distribute Ram Products in Canada. If people are interested in parts or new equipment in Canada they can call 1-800-667-3770.

[@Pinkielover]

junk handpiece. i know the owner of the company that makes these.. my father was in this business for over 45 years .. need parts i have some still left from my dads old repair company.. nsk so much better