Rancher 350 Engine Rebuild

  Рет қаралды 23,745

Four wheeler Doctor

Four wheeler Doctor

Күн бұрын

Пікірлер: 90
@Fra-jc1eh
@Fra-jc1eh Жыл бұрын
Really appreciate the opportunity to watch and remember a lot of things I'd forgotten.
@nathanielcox9944
@nathanielcox9944 2 жыл бұрын
You are the absolute best on KZbin. Straight to the point, no editing even when there's a problem, and very detailed. You are more valuable than you realize. Thank you so much for all of your videos!!!!!
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
Thanks and thanks for watching. I try to show it as I find it.
@blakeowens4334
@blakeowens4334 Жыл бұрын
I have a 350 rancher es 4x4 i have took apart 8 times and ever time green light is on but its in first gear thats all it has please help me
@blakeowens4334
@blakeowens4334 Жыл бұрын
Can someone tell me what im doing wrong
@Jnelson-z3r
@Jnelson-z3r 22 сағат бұрын
Having same issue did you figure it out
@stevephiillips2906
@stevephiillips2906 2 жыл бұрын
Awesome video, plenty of top end videos but it’s hard to come by a video including the bottom end for the 350. Kudos
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
Thanks and thanks for watching
@devynsheets5274
@devynsheets5274 9 ай бұрын
Been watching alot of these, havent figured it out yet but ive learned alot from you! Appreciate you taking the time to post these!
@pbkcustomzpitbikeking3876
@pbkcustomzpitbikeking3876 9 ай бұрын
Should it be in gear after putting everything back together made sure I put trans back together and aligned the flat head piece on the shifter drum
@Robert-p5q
@Robert-p5q 26 күн бұрын
Question 350 Rancher350 trx fe. rebuilt motor runs .Found out it was not charging.Magneto bolts came loose and damaged the stator.Purchased a used magneto and new stator.Cranks got spark wont fireup
@simeonieweetaluktuk174
@simeonieweetaluktuk174 Жыл бұрын
So I was tearing down 2 motors, the other one had a bearing on the shift drum, like the one that butts up to the neutral switch sensor. the two were diffrent crank case. so I knocked the bearing out to put in the shift drum. and the concerns me.
@SethTate-wf9vm
@SethTate-wf9vm 10 ай бұрын
About to do a bottom end rebuild on my 01 350 rancher should I stay away from aftermarket kits such as hot rods or wrench rabbit ?
@Thatslow_rfz125
@Thatslow_rfz125 28 күн бұрын
Great video, I took mine apart like this and put back together now my transmission and the output shafts bind up, any help would be appreciated
@Jnelson-z3r
@Jnelson-z3r 22 сағат бұрын
Having same issue did you figure it out ?
@Thatslow_rfz125
@Thatslow_rfz125 19 сағат бұрын
@@Jnelson-z3ryea so the gears will only turn a little bit if it’s in gear , but after u can find neutral the gears rotate freely
@rylandmcclain846
@rylandmcclain846 Жыл бұрын
Awesome video, I’m about to rebuild a 2006 that still runs decent but was ran low on oil so now it knocks. Is there any wear i should look out for since it was run low?
@FourwheelerDoctor
@FourwheelerDoctor Жыл бұрын
Most of these that were run low have a damaged piston pin. Make sure you check it.
@calebhildebrand801
@calebhildebrand801 Ай бұрын
@@FourwheelerDoctor sadly thats why im wacthing this helpful vid i got my pin to moove about half way with a ball joint tool but cant get it do you need a press for the shaft or is that something you can try at home im not sure who could press it
@christopherspraglin8206
@christopherspraglin8206 Жыл бұрын
When u put the motor all back together are tou able to put it back inside the frame of the rancher 350
@Troy-f2h
@Troy-f2h 5 ай бұрын
Good easy to learn video some people can't teach you can lol
@FourwheelerDoctor
@FourwheelerDoctor 5 ай бұрын
@@Troy-f2h thanks and glad I could help
@robertfrankowski3244
@robertfrankowski3244 2 жыл бұрын
Ever use one of the wrench rabbit kits on these? Got a noise coming from bottom end. Pretty sure it's from the bottom end. I've adjusted valves multiple times. The clatter comes and goes through the rpm range.
@robertfrankowski3244
@robertfrankowski3244 2 жыл бұрын
Comes with a hot Rods crank
@baseballplayer2121
@baseballplayer2121 17 күн бұрын
Do you clean the cases in parts washer solvent with the bearings still in?
@Walter-tr4dl
@Walter-tr4dl 2 жыл бұрын
I have a clutch nut with out the tab does it make a difference with or without it
@marcuhh3262
@marcuhh3262 2 ай бұрын
@27:06 wats that washer part number will it damage it if I don’t put it?
@NickandWesley
@NickandWesley 2 ай бұрын
What do I do when I pit the 350 all back together and it cranks but not driving like it’s stuck
@dawsonanstey9557
@dawsonanstey9557 Ай бұрын
Loved this video so much....had to subscribe and pop a quick question. My first Honda 350 motor work. (TRX350FE). ES Problem. The little tip was broken off the "SUB-GEARSHIFT SPINDLE" that drives the shifter plate that rotates the star on the shift drum. Figured plate was surely the problem. OK ... with all shift parts out and only the star on the drum left, if I take the pressure off the little tension roller, should I be able to freely turn the drum back and forth? (maybe turning the clutch as I try say...its in a gear ...maybe 3rd)? The drum only turns within an angle of say 20 deg. (about half a star cog) I'm thinking it should be pretty much free to spin within its limits. Don't want to do a split if not necessary (:
@ct4au
@ct4au 3 ай бұрын
I need to replace my shifter spindle (it’s stripped, and the seal is leaking). Do you have any info on how to do that?
@dustinyeager9016
@dustinyeager9016 3 жыл бұрын
Thank you sir for the video. Finally finished my 350 rancher today
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
Good deal. I hope everything went good.
@dustinyeager9016
@dustinyeager9016 3 жыл бұрын
@@FourwheelerDoctor everything went perfect. I bought this rancher with a bad motor and rebuilt it with help from your videos. I do have a question though. The previous owner grounded the temp sensor wire to the motor to make the fan stay on constantly. Will that make the oil temp light on the dash stay on constantly as well? Or do I have a different problem?
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
@@dustinyeager9016 yes it will make the oil light stay on all the time if it's grounded out.
@dustinyeager9016
@dustinyeager9016 3 жыл бұрын
I have a 2000 foreman 450. Do you know where I can find a bottom end kit for it. I can't seem to find a crank anywhere
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
@@dustinyeager9016 those are getting harder and harder to find. The last one I ordered was a while ago and it took forever to come in. Check out Mrcrankshaft.com. I've had him rebuild some for me before and they work out perfect had a pretty good price.
@connieroy-x9h
@connieroy-x9h Жыл бұрын
Great video, I have a question about the change clutch, I bought a 2006 honda 350 4x4 FM with only 2700 km on it mint condition but it sat in a non heated building for about two years. The change clutches were stuck so I was told to put it in high gear, lift up on the shifter and rev the engine to break them clear after they broke clear I was told to lift the shifter until it slipped a bit to clean the plates. That worked, but every time it sat it would stick again. So I pulled the clutches and they had a bit of rust on them , so I cleaned them off with a really fine paper, put it back together it worked fine , but if it sits for a couple days it still sticks a bit, once it breaks free you can ride it all day without an issue. Something is just nor right, I should have put new plates and friction discs when I had it apart but guy at Honda said nah they look ok. Any tips or advice would be greatly appreciated, thanks Barry
@juledoren
@juledoren 5 ай бұрын
Good video, just got my new shift drum in, probably do piston since its all apart
@terryworthen103
@terryworthen103 2 жыл бұрын
Subscribed my 350 was supposed to be rebuild and started blowing white smoke don't know why but can't change oil have to tilt bike because it will break if bolt takes out. Any advice on white smoke.
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
Are you getting oil in the airbox?
@martinwallace6833
@martinwallace6833 Жыл бұрын
Brilliant video and commentary. I have a 2004 Rancher 350FM with the motor still in the frame. I as replacing the swingers bearings and noticed the output shaft in the rear crankcase cover offset from centre and has torn the oil seal apart so oil has been leaking into the rear driveshaft boot. I find I can move the output shaft to centre it but I would have thought it should always be centred. I prised out the oil seal and expected there to be a bearing behind it in the rear crankcase cover and thought it might be damaged. Is there a bearing there? I can't make out if there is supposed to be one there or not from the parts diagram. Have you experienced this problem and if it is a bearing issue can it be replaced with the motor still in the frame?
@aleemrahim6846
@aleemrahim6846 16 сағат бұрын
Well educated saved me with the reverse locking lever 🙏 thankss
@michaelmarcum3789
@michaelmarcum3789 2 ай бұрын
Which way do I point arrow on my piston,
@SuperRyansWorld
@SuperRyansWorld 2 жыл бұрын
Thanks for the great video, question on the centrifugal clutch and drum the clutch lining measure out good but the drum is grooved what do you recommend thanks
@davidfloyd6932
@davidfloyd6932 2 жыл бұрын
I have a 2003 honda rancher 350 when it in Neutral it going in Reverse when I gave it the gas to my at. Any Answers thank
@hondaatc1987
@hondaatc1987 Жыл бұрын
I can't get my front cover back on all the way.. tried everything.. it's only about an 1/8 on an inch..so close but will not go back on!
@1972bcain
@1972bcain 2 жыл бұрын
Do you have to separate the stator and it’s cover from the case cover or can you just remove the entire cover to access the engine? I believe I just need to get to the timing chain and it’s tensioner…. Don’t need to replace the stator it’s working perfectly.
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
You have to take the stator cover off first. There's a couple bolts on that cover that also hold the next cover on
@1972bcain
@1972bcain 2 жыл бұрын
@@FourwheelerDoctor Thank you sir! And I rewatched your video and you covered that I just missed it... I will order the gasket along with the fly wheel puller and whatever else I need once I get everything down. Valves are adjusted per your videos and it got quieter but still making noise. No loss of power, starts easy, no smoke, oil looks fine etc. Should just be the chain or the tensioner I hope.
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
@@1972bcain the tensioners are pretty tough and very seldom give trouble on these bikes so more than likely it's the chain
@1972bcain
@1972bcain 2 жыл бұрын
Update- it was not the timing chain, sigh. Connecting rod eye is wollered out and wrist pin has a lot of play causing all the noise as the piston slips around…. Cylinder wall and piston are showing wear. Ordered new crankshaft, rod, piston, cylinder, gaskets etc…. Big thank you for your 350 Rancher playlist Sir! Taking the edge of being nervous about this big of a rebuild.
@radioace318la
@radioace318la 2 жыл бұрын
hey man, enjoy your stuff. thanks for sharing. One question, Have you replaced the shift plate in a 350 Rancher ES without pulling the engine? I hear you can do this in frame but I would think it would be a lot more of a headache. Do you have to pull both clutches or can you sneak in out and back in without too much of a PITA? Thanks again Cheers from Louisiana.
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
If by the shift plate you talking about that plate behind the front cover that often breaks on them, yes you can replace it without pulling the engine. It's not very hard to do but you do have to pull the clutches.
@philipjean1086
@philipjean1086 3 жыл бұрын
Hi doc got a good deal on 01 350rancher Es it was stored inside, only 1200 miles on it pretty will mint but it wouldn’t shift, replaced angle sensor and broken gears for shift motor. I also replaced star piece on shift drum and shift plate. It changes gears now perfect 98% of the time,but sometimes it won’t shift at all. I’m sure it must be the change Clutch have tried to adjust many times but just can’t seem to get it perfect. Did have it apart when I changed the shift plate and never noticed anything abnormal. I’ll take it out to my trapline in northern Canada and use it the way it is but it just bugs me that I can’t get it right. Any thoughts or seen any similar symptoms. Great videos thanks
@MyChannel-d2e
@MyChannel-d2e 3 жыл бұрын
Yesss I was wondering when u would do the rancher
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
Thanks for watching!!
@jasonhorton4798
@jasonhorton4798 3 жыл бұрын
need to pick your brain again , I have a 02 350 rancher ES with a meter that you cant read to get codes, Problem is every time you shift to a gear its a second or so delay before it shifts and it jerks every shift because of it , I adjusted the clutch got that out of it now it will only shift neutral to 1st and back i cant get the fine line in between , havent pull it apart yet , but thinking it might be the shift return spring weak , any thoughts or ideas from past repairs? Its also has one of those aftermarket sensor bypass kits on it for shifting not sure if that comes into play or not , Appreciate any help you could pass along Thanks , using the Manuel shifter it feels mushy like it doesn't want to return to catch the next gear
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
Sound like it's probably either a weak shift motor or that shift return spring like you said. The aftermarket relays that makes them shift bypassing all the sensors so the only leaves the shift motor and the buttons. I've also taken apart and cleaned the grease out of the shift gears behind the shift motor because sometimes that old grease will get hard and real sticky and will make them bind up too.
@jasonhorton4798
@jasonhorton4798 3 жыл бұрын
@@FourwheelerDoctor Thanks for your reply your channel has really helped out , I keep 5 hondas for the kids to ride , So something is always broke down , They ride them hard ,I finally had time when i got in last night to stand it on end and pull it apart , The spring loaded arm on the star was bent down under it somehow so the roller wasnt making contact with the star , that was the only thing i found , i'll stick it back together today hopefully that was it, everything else looked fine , i did stick a new shift motor on it i had on the shelf as well , was hoping to find something broken or worn out , I just picked it up cheap for my grandson , with the front axels worn out ball joints shot and boots torn, so have all that to replace , Again Thank you very much
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
@@jasonhorton4798 glad I could help. Make sure that 10 mm bolt in the center of the star piece is tight. I've had them back out before. It doesn't hurt to put some lock tight on it before you put it back together.
@schlabachcs
@schlabachcs 2 жыл бұрын
How much does something like that cost to get done
@calemurphy8917
@calemurphy8917 2 жыл бұрын
Is it hard to replace a one-way bearing on one
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
Not too hard. Just have to pull the front cover and clutch off.
@jasglas1033
@jasglas1033 2 жыл бұрын
Man thank you for your Videos!!! I need to replace the Centrifugal Clutch one way bearing but my clutch pads are pretty worn like the one in your video. Which aftermarket clutch do you buy for these?
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
I have had good luck with the caltrec brand off eBay
@blairguinea6811
@blairguinea6811 2 жыл бұрын
Thankyou for your time Sir, this is an awesome tutorial
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
Thanks and thanks for watching
@leandrodosreisvilela4807
@leandrodosreisvilela4807 Жыл бұрын
4x2?
@FourwheelerDoctor
@FourwheelerDoctor Жыл бұрын
I think this was a two-wheel drive bike but the two and four wheel drive are ompletely identical with exception of a small short shaft that comes out the front of the motor to drive the front differential and a hole in the front cover for that shaft to go through. The 2 and 4 wheel drive bikes are basically interchangeable with exception of that shaft and that hole in the front cover.
@jareddiaz8538
@jareddiaz8538 Жыл бұрын
Well, add me to the list of people who didn't get the sensor aligned properly. I watched this video first, carefully pointed the long side towards the N, confirmed the gearshift was in neutral. FmL. Symptoms are no neutral light on when in neutral, gear display is all over the place and inconsistent with actual gear it's in.
@FourwheelerDoctor
@FourwheelerDoctor Жыл бұрын
That stinks. I can't say I have gotten it right every time myself.
@ChurchInAshes
@ChurchInAshes Жыл бұрын
Man I don't have the brains to do this stuff, but I'm starting to realize why my mechanic is charging me so much. So difficult
@FourwheelerDoctor
@FourwheelerDoctor Жыл бұрын
There are a bunch of steps and I make it look easy because I have done a few but but still nothing a diyer with a few tools can accomplish.
@dirtmonkey1337
@dirtmonkey1337 3 жыл бұрын
Dude, thank you!
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
Thanks for watching
@chadg4261
@chadg4261 2 жыл бұрын
Subscribed, thank you for these videos!
@rickfink464
@rickfink464 3 жыл бұрын
Do you exclusively only work on Honda?
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
Not really. I really work on anything but it just seems like most folks around here have Honda's so that's what I end up working on. I also have done a bunch of motors in them so I can about do them with my eyes closed.
@rickfink464
@rickfink464 3 жыл бұрын
@@FourwheelerDoctor Where are you located and what do you charge to rebuild a motor? My '02 Yamaha Big Bear 400 4X4 that I got in March, slips out of gears sometimes and I bought the transmission gears off of Ebay a couple of months ago
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
@@rickfink464 I'm located in south Carolina
@rickfink464
@rickfink464 3 жыл бұрын
@@FourwheelerDoctor I live in West Virginia, but my dad lives in Cheraw, SC and I lived in NC for 12 years near the border of SC, so I'm pretty familiar with the area
@rickfink464
@rickfink464 3 жыл бұрын
I have the Yamaha factory service manual for my 4 wheeler by the way
@6foot8jesuspilledpureblood82
@6foot8jesuspilledpureblood82 6 ай бұрын
Just too hard for me I'm not smart enough. I'm going to forget where to put things back and lose half the parts. This is not for noobs. I might risk the top end rebuild and pray I don't need to do this bottom end. Hope I don't have a bent rod because I heard an awful noise but the engine kept running and oil was very low.
@COOP740
@COOP740 Жыл бұрын
Subscribed! 😂
@dannycoultas265
@dannycoultas265 3 жыл бұрын
Mine is manual shift and all the same in the flywheel side infact all the same baring the stupid electric shift motor, some good tips for noobs here like but why buy a whole crank wen a rod is 1/120 and 30 min work probs a 1/4 of price of crank should have left oil pump alone used the time on crank and save probs half your bill can only guess u dont mind spending customer money or lack the skill n tools to do rod alone
@codyswilley
@codyswilley 3 жыл бұрын
🤣🤣🤣 I love your shirt
@FourwheelerDoctor
@FourwheelerDoctor 3 жыл бұрын
Thanks man. I have some good ones.
@MrBmcgraw
@MrBmcgraw 2 жыл бұрын
Really like your videos! BUT……..Dude….. You left some stuff out! I had to pull my shit back apart to put the parts back in just like you did when you shut the camera off and came back on for the next step…… Figure out how to edit the missed parts in.
@FourwheelerDoctor
@FourwheelerDoctor 2 жыл бұрын
If you don't mind me asking which part did I skip? I don't even remember me doing it. I'll see if I can edit it in or put text in to explain. That's the thing that stinks about KZbin videos is you can't add sections to them once they are uploaded without uploading an entire new video. Which I may do that if I need to.
Honda Rancher 350 Top End Rebuild
54:59
Four wheeler Doctor
Рет қаралды 22 М.
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 30 МЛН
The evil clown plays a prank on the angel
00:39
超人夫妇
Рет қаралды 53 МЛН
Rancher 350 valve adjustment
19:21
Four wheeler Doctor
Рет қаралды 9 М.
Can-Am Outlander Rear Diff rebuild
56:13
Four wheeler Doctor
Рет қаралды 16 М.
First Ride of a Honda Rancher 350 Electric Shift!!!
8:56
Lxnar514
Рет қаралды 6 М.
How to Install Gear Reduction on Honda Rancher 420
56:05
Four wheeler Doctor
Рет қаралды 2,3 М.
Honda Rancher 350 with Oil in Airbox
13:11
Four wheeler Doctor
Рет қаралды 40 М.
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 30 МЛН