I'm replacing the half shaft and hub on the right front wheel of my 2007 Range Rover supercharged. In this video I show you the process of doing the work yourself, plus maybe a helpful hint to make your process go smoother.
Пікірлер: 24
@atube29813 жыл бұрын
My axle broke this weekend... I'm gonna try to tackle both front axles ... your vid was helpful especially the part about prepping the axle splines with a dremel... I wrestled for 2 days with the last land rover axle I changed...lol wish I knew that trick before sending it to a shop....lol... thanks
@CentTxLiving3 жыл бұрын
That's great, thanks for the feedback. 👍
@SeanPo1THC2 жыл бұрын
can you remove halfshaft to run rear wheel drive only?
@CentTxLiving2 жыл бұрын
I have never tried that, but I have heard that the transfer case won't allow that to happen; meaning both shafts must be attached. I don't know this from first hand experience though, I've just never tried it. 🤷♂️
@rodneys9805 Жыл бұрын
any luck on that, trying to do a ls swap myself
@CentTxLiving Жыл бұрын
Sorry bud, never tried.
@marktowill28283 жыл бұрын
I did a fair amount of research on it uses a radio wave antenna. .general consents is turn it off with an OB2 somehow that what the Brits told me
@CentTxLiving3 жыл бұрын
Thanks, I think i will pursue that.
@frenchyjones3 жыл бұрын
I have a 2008 Range Rover supercharged and I am having an issue with the tire pressure senor module! Have you had this issue with your truck at all?
@CentTxLiving3 жыл бұрын
Yes, I had the sensors replaced and the control unit recalibrated for the new sensors. A week later it faulted again, so I just let it go for now. Apparently, the proper remedy is a new light control module, and I have read that the system will reset automatically.
@marktowill28283 жыл бұрын
I have also a 2008 HSE .Same problem with her. it will go a week without dash light then it just came on. but generally the light is accompanied by" check tyre pressure" statement.I just ignore the light and am glad it stopped the statement. hope this helps
@CentTxLiving3 жыл бұрын
Yeah, mine is back at it with the same issue as yours Mark. I suppose it's time for a new tmps ecu. I hear they are easy to replace though.
@jessicapoynter34272 жыл бұрын
Mr. Rollins, what is the cable that is connected to the back of the hub?
@CentTxLiving2 жыл бұрын
Mrs. Poynter 😁, The actual cable is the emergency brake cable, the other connector will be for the wheel speed sensor that provides info the the abs, hdc, tc, and so on.
@jessicapoynter34272 жыл бұрын
@@CentTxLiving Thank you sir! Now to be able to actually locate just the cable. :)
@CentTxLiving2 жыл бұрын
You're probably better off with a salvage yard. It should be fairly straightforward to replace.
@bobamst3312 жыл бұрын
Are you replace maybe a seal on that CV axle.?
@CentTxLiving2 жыл бұрын
I replace the half shaft because the boot tour, not anything to do with the seal. Was that your question?
@bobamst3312 жыл бұрын
Yes, because I need to. I buy the seal and now I don't know if it's Fitts and how its about the job like easy or not...😑
@CentTxLiving2 жыл бұрын
If you're just replacing the seal, then you're just removing the half shaft from the differential. That particular process is fairly simple because the seal is on the differential itself. I found the hard part to be with removing the actual half shaft.
@bobamst3312 жыл бұрын
@@CentTxLiving tnx. I will see for couple days and I will share info about that on KZbin .
@CentTxLiving2 жыл бұрын
That's great, I'll look for it when you post it. 👍