Hi , I recently came across this video , do you know where I could purchase the white plastic pick up pipe that is attached to the filter for the auto gearbox. The one I have is broken and I have tried searching for them on eBay but isn’t coming up with the right ones. If you could get back to me and let me know the name for it or the part number please I will appreciate that a lot.
@WorkOnP384 жыл бұрын
Hi Lottie. The part number is TQW100030. Don't forget the o-ring RTC5818. Thanks for watching!
@ismaaelabuyunis43559 ай бұрын
Hi , can you please explain how to change Automatic Gearbox Speed Sensor - Turbine ? Thanks a lot
@robertrichardson17795 ай бұрын
Perfect vid, to the point, no waffle, great detail, thank you
@leslydauphin25014 жыл бұрын
Great Job Man. Blessed.
@luckymitelela66854 жыл бұрын
Boa tarde. Tenho um R. Rover P38-1996 e esta com gear box fault. O problema apareceu quando usei a traccao e forcei um pouco ate patinar. Como posso resolver este problema? Lucky - Mozambique
@martinruss24234 жыл бұрын
Great video but my 99 P38 doesn't appear to have a fill plug. A forum suggested I had to refill from the dipstick tube but that would take hours. Any ideas? Thanks
@sayranci1213 жыл бұрын
Hi john.thanks for all videos .all great.I have 1998 4.6 litre hse.i can only use gearbox manuelly.i changed oil and clean the filter still the same..what can i do next ?
@tamero524 жыл бұрын
Thank you for your video. How can we check transmission oil in 2000 p38?
@TeamLandJ3 жыл бұрын
Thanks very much for a great video! Very Helpful
@khndenmark5 жыл бұрын
Thank you because you are back again. We need your videos about the p38
@WorkOnP385 жыл бұрын
Hi, yeah I haven't given up. There will be more videos coming :) Thanks for watching and for the support!
@Ghostole4 жыл бұрын
Hei Odd, Ole Martin her 😀 har sett alle dine vidioer og har hatt mye hjelp fra dem. Lurer bare på en ting når det gjelder min P 38, når jeg rygger tar det lang tid å få opp turtallet og bilen går tregt i 4-5 sekunder før den kommer, gelder også når bilen settes i drive, tar litt tid føre turtallet kommer opp. Hva kan det være ?
@ThePatchworkProject4 жыл бұрын
Thanks for your great videos - Any recommendations re the sourcing of a filler pump system for this job?
@paulgiddy56313 жыл бұрын
Is the replenish procedure the same for the dipstick version?
@gordonwedman31795 жыл бұрын
thanks for the new video. I need to do the trans fluid on my 2000 so this was a good review. Have been in Mexico since November without my P38 but going home soon and will resume working on it. Cheers
@Voff015 жыл бұрын
Hei nabo, glad to see you're back! 1998 P38 4.6 HSE owner in Sweden here. Tried to add you on Instagram but no go. Tech-tip: if you're looking for easy editing, check out Adobe's Premiere Rush CC.
@WorkOnP385 жыл бұрын
Hei bror Mario. Life's been busy but the videos will continue. Maybe I made a typo in the Instagram link, it's instagram.com/0ddj4rl3/ so hope that works. I'm quite happy with iMovie, but am trying out Final Cut for a few future ideas. Thanks for the tips and for watching!
@richardclarke44054 жыл бұрын
Could I ask you a question please . I have a year 2000 p38 dhse . The problem I'm having is there is a lack of power from a standstill notice it more in reverse I've checked the map line fitted a new map sensor and it's still the same
@WorkOnP384 жыл бұрын
These engines are a bit hesistant until the revs build up and boost builds up. Mine lags about 1-2 seconds before it wakes up. Thanks for watching.
@chrishynes15032 жыл бұрын
another great video, thanks
@Mrcaffinebean5 жыл бұрын
My transmission pan was smashed by front drive shaft u joint breaking. I kind of want to replace it and kind of want to leave it and call it preclearanced.
@WorkOnP385 жыл бұрын
Ouch, I hope the pan survived. Could have quickly been a expensive fix if all the engine oil drained out and the engine became damaged because of that. Sounds like you had a bit of luck in the middle of bad luck with the drive shaft u-joint. Thanks for watching!
@ad1das414 жыл бұрын
Thank you. I only got a bowl out from the old fluid it doesn’t seem like much, did I do something wrong? Not as easy as it looks at least my current experience but I’m working on it
@WorkOnP384 жыл бұрын
You should easily get 5 litres or more drained out if you drain from the bottom plug. If not the transmission probably has been low on oil. Any signs of leaks around the pan, shift lever or drive shaft? Refilling it can be a bit tricky if you don't have stands or a lift to gain better access. Thanks for watching!
@sebczajna7005 жыл бұрын
Super, I must check if my car have greasing point because i dont see antything like that on my P38 on last inspection. Best regards
@WorkOnP385 жыл бұрын
Hi Seb. They should be there. Might be dirty or broken off perhaps. You can replace the zerk points if needed. I recommend you grease them after driving the car for a while so that the grease has warmed up and it'll be easier to insert new grease. Thanks for watching!
@RicardoSalinasFournier5 жыл бұрын
Great you are back! Thank you 🙏🏻
@WorkOnP385 жыл бұрын
Thanks Ricardo. More videos are coming. Sorry for the long delay. Thanks for wathing!
@rmq28514 жыл бұрын
Top man.....
@stefanoranucci23474 жыл бұрын
top top top
@testopatia1065 жыл бұрын
You did not mention the part number for the Transmission part nos..love your videos though
@WorkOnP385 жыл бұрын
Hi, and thanks for watching. If you check the description you should find the part numbers.
@juris64565 жыл бұрын
Paldies Tu esi labākais!!!
@WorkOnP385 жыл бұрын
Thanks for watching!
@richardclarke44054 жыл бұрын
I've followed your video and I'm still having a issue with reverse I dont have full reverse power
@WorkOnP384 жыл бұрын
Sounds like worn and slipping cluthces. Thanks for watching.
@ruisalvador35164 жыл бұрын
if you input air pressure in the tube of filter the torque oil come out ?
@WorkOnP384 жыл бұрын
Good question. I don't think you'll get all out as the air can escape past the oil in many passages. And the pressure might harm components, so I wouldn't try it. Just disconnect the return line and add oil while running the engine until all the oil is out. Thanks for watching.
@fakereality37924 жыл бұрын
Your videos are fantastic. You are much appreciated 👍👍👍
@WorkOnP384 жыл бұрын
Glad the videos are useful. Thanks for watching, Hugh!
@fakereality37924 жыл бұрын
Work On P38 After 14 years of owning my P38 I found how to stop the EAS from going wrong. It was always going down on the back. Thought it was airbags and was about to replace them. Much easier fix. Now it works perfect and never drops down. I’m not sure how everyone hasn’t discovered how to solve it. My P38 is perfect now. Never had any problems except air suspension with it. Numerous compressor pumps later 🙈
@rija6124 жыл бұрын
thanks for your video my friend
@WorkOnP384 жыл бұрын
You're welcome, Rija. Thanks for watching!
@Martin_IPL59905 жыл бұрын
Really useful video again. have made a note of the ATF. thanks.
@sandzak-rq4fg4 жыл бұрын
😍👍🏻👍🏻👍🏻
@WorkOnP384 жыл бұрын
Thanks for watching!
@testopatia1065 жыл бұрын
Where is the descriptions????
@WorkOnP385 жыл бұрын
Check these guides: www.google.com/search?q=youtube+how+to+view+description