Raptor Spray in Bed Liner DIY | 2021 Chevy Silverado 2500 Custom Duramax

This is my Spray in Liner project on my 2021 Silverado 2500 HD Custom Duramx Truck.
Here are the links to the products used in the video:
Raptor Bedliner kit: amzn.to/3g7bEqI
Masking Materials: amzn.to/3yQzZbH
Pressure Regulator: amzn.to/3sogEfF
Painting Resporator face mask: amzn.to/3k8BEU2
Here is a link to the playlist for this 2021 Silverado 2500 :
• 2021 Silverado 2500 HD...
For Promotional opportunities or business inquires email me at: [e-mail]
The above links are my Amazon affiliate links, Which by using will support the channel. Thank you! The above links are my Amazon Affiliate links, as an Amazon Associate, I earn from qualifying purchases. Thank you for supporting my channel!

[@Myksgarage]

Link to bed liner kit: amzn.to/3k1PU0A Thanks for watching, be sure to like and subscribe!

[@martinrodman3914]

Good video. Right to the point. I’ll be doing this to my 2016 Silverado LT in a few weeks. I have a shop I can spray in so maybe not as messy.. your work was very clean!!

[@Myksgarage]

Thanks for the comment, good luck your project

[@mrbeatty13able]

Excellent job.

[@Myksgarage]

👍

[@BoStErO1905]

brave man, thanks for doing this

[@Myksgarage]

It wasn't too bad, the prep is the hardest part

[@mrbeatty13able]

I will look to see but if you haven’t can you do a two year update of this video? Thanks

[@Myksgarage]

I sold the truck shortly after doing this

[@RyanHarker]

Thanks for this video! So, I have a 2009 F150 that currently has a plastic drop-in liner. There's a bit of rust under the liner, so I'm thinking of spraying in a liner like this. What would you do about the rust?

[@Myksgarage]

I would just sand it down, even use a wire wheel, then just coat it

[@roberthaynes387]

Does it have to be a certain temperature if painting it on outside? Obviously not in the direct sunlight or wind.

[@Myksgarage]

The warmer the better, and yes, avoid windy days or direct sunlight

[@jimmyhamm6041]

Anymore we all need to put our vehicles on a rotisserie and completely lingered underneath so as the salts and weather do not eat it away. IT sickens me you pay between 50 to 80 thousand for a new vehicle & nothing to protectthe under side and within 3 weeks it is starting to rust the new metal.

[@Myksgarage]

Yeah that is crazy that there is such little rust protection

[@dancarroll2820]

Hello , did the joints of the bed (where the sides meet the bottom ) have a rubbery caulk ? If so, did you spray over it ?

[@Myksgarage]

Yes, just sprayed right over them

[@dancarroll2820]

Thanks !

[@robindthompson]

Level with me dude how easy is it to mess this up? I have a 22 frontier

[@Myksgarage]

It's not hard, the prep is the hardest part, And then making sure you have everything taped off and covered so you don't get any of this bedliner on the paint of the truck. I say go for it!

[@Guhtix10]

I do this professionally. As he said. It’s all in the prep. Spraying is the easy part. Just make sure you get high contact areas with proper thickness. And tape off your areas well and you’ll be fine!

[@bblauter]

It has now been a year, how did it hold up?

[@Myksgarage]

It's held up well, I've kept a mat on it so the mat as taken all the abuse.

[@mattkaiser8984]

@Myks Garage Good idea!

[@je1279]

Do you have a water separator on your air compressor?

[@Myksgarage]

I do not

[@ihus9950]

How's it holding up?👍🏻

[@Myksgarage]

Pretty good, I keep a rubber mat on bottom so it doesn't get beat up

[@ihus9950]

@@Myksgarage Good Idea👍🏻