How to Install Anchor Bolt Fastener in Concrete Columns & Wall.

[@mamtjha]

बहुत ही उपयोगी जानकारी दी आपने। बहुत बहुत धन्यवाद आपका

[@lalitrawat90]

Mistakes that were made while installing hilti anchor bolt: 1. Machine was vibrating way too much which may lead to loose fitting. 2. You skipped video cleverly when he was hammering anchor bolt with the help of hammer. Bolts were not going in even after applying enough force, and you did cut them off as we can see on 4:22 , which creates doubt that your drill bit was quite old and has lost sharpness on tip. 3. Fitter was hammering on nut after keeping them on edge which I totally understand that he wanted to save bolts thread. But if you notice that those anchor bolts dont have thread outer side and have less diameter also. That is because you can hammer the bolts, since there is no thread outside have lesser dia, you nut can come outside without any trouble. 3. You must have to tight nuts and bolts with Ring spanner only. Not with D-Spanner.

[@izmirfication]

yes ,I appreciate all the work done at field but not getting the anchor bolts red mark as close as possible to concrete surface is very crucial as this is explained above, it is not an acceptable excuse like the driller couldn't get deeper..

[@PrashantKumar-lx2kr]

Useful,thank u so much

[@kinzaandfizan8393]

Sir in fastners par 400 kg ka main ms gate laga sakte he kya

[@vlogergtm4774]

Yeh sirf concreate k liye he ya eat pe v lagasakte he

[@surendramittal2315]

Hole me Camical use karna hai ya nahi

[@DRAGON_FRUIT_373]

Bahut achha, Naya kuch sikhne ko mila, lekin mere Ghar banate waqat mistri ne collum ko adha kat ke balcony bana diya

[@mdshahzad4267]

Ghar ke chokhat.kalam me kaiise lagate h .kitna inch hona chahiye

[@preetisingh-rq7ph]

Sir in fastener par lohe ka main gate b lagaa sakte hai ???

[@dukaleashokdukaleshravan2029]

Yeh wedge type anchor fastener hai kya?

[@abhishekgiri6207]

Isko bina fixer camical ka use kr skte h??

[@yasirmahmod6832]

Pls, can i install C channel of gypsum boards by rawl bolts in ceiling ?

[@surajsyangtan46]

sir mereko usi tar niche chhatme iase plate me bolt lagana hai u kaise konsa bolt laga sakta hai?

[@sanjeebtamrakar8610]

what about the reinforcement of column when you are drilling the hole? Is it ok if the drill beat crushes the re-bar?

[@PrashantKumar-lx2kr]

Same questn

[@Rabiya-fabrication]

Kiya ye ek tan wajan jhel sakta hai sar

[@psingh5941]

Sir stone Bolt kya hota h

[@shubhenterprises2892]

Sir ghar ke elevation me 150 x 75 (17 kg/mtr weight) ki channel lagana hai , length - 40 ft, please suggest anchor fastener size and number of insert plates for 40 ft length

[@ma-lakshmifabricator7549]

Overall, this is a highly informative and enjoyable video for anyone interested in fabrication. It showcases your talent and expertise while providing valuable insights and inspiration to fellow enthusiasts. Keep up the great work, and I look forward to watching more of your content in the future 👍👍👍

[@Singh-pq7tk]

Iss plate ka use kaise hoga.

[@Ajaysingh-or7il]

Plate kitna MM hai Sir ??????

[@mostwanted_007]

Hello sir! Can we use these types of anchor bolts to hang jhula from ceiling? How much tension load can these take?

[@Vijaykumar-zq3yu]

Shaandaar video sir jii

[@Mamta4455]

16mm me kitna mm hole kiye

[@rameshmarupuramesh5683]

Do u have any method of Direct tensile strength method and required equipment, please share the details

[@surajkuk5048]

Sir maine gate lgana h lekin jha gate feet karne h wha beem h agr beem tode g to vo kamjor ho jayga keya kar skte h gate ka 1 side ka weight 100 kg h yaani total 200 kg

[@LITTLEMASTIBAZz]

10mm fasner me kitne mm bit daalna he yeh to bata do

[@sanjaladebbarma3509]

Sir apka drill machine ka price kitina hai or kasa company hai

[@adwaitkumar]

Bhai kya is bolt fastener ke prayog do pillar ke bich me ek aur pillar daalne kar sakte hai.mere yahaan 21 feet ki doori par 9×15" pillar hai.hum first + 2nd floor daalna chahte hai. Is bolt fastener beem me lagaa kar nichey aur upar pillar first floor ke liye kar salte hai .kripaya bataaye

[@rbsinghcivilengineeringaca6777]

Deer ish situation mein aap rebaring beam ka use kar sakte hai, Anchor fasteners se jada achha rahega. Rebaring ke bare mein bhi video hamare channel mein available hai aap dhekh sakte hai.

[@whitewalkers9793]

Sir isme camical nahi dalte kya...

[@rbsinghcivilengineeringaca6777]

केमिकल डालने की जरूरत नहीं पड़ती है

[@hiteshkhare413]

180 kg ka gate lga skte h sir bataye plz iron gate

[@mahaveergurjar4066]

❤

[@raghunathbendkule3644]

Ekdam parfekt इन्फॉर्मेशन देते है आप

[@dukaleashokdukaleshravan2029]

Can we use this for conveyor column base plate fixing

[@sudiptachatterjee6730]

M16 bolt ke liye drill bit kitna ka Lena parega?

[@mohammadhussen9622]

16

[@Alokkumar-bd8ye]

Sir mera ghar ban chuka hai, aur frant me 2 round pillar hai jis par balcony ka pura load hai, avi main us dono pillar me gate ke liye hole kaise karwau. Plz help kijiye

[@devilranjan3362]

Anchor fastener size kya tha

[@prabhanjandalia2366]

Good job sir

[@basavarajt4]

Sir pillar structure ke liye konsa size ka bolt use karna hai

[@keneilhouliesolo1883]

Very nice and clear explain... excellent 👍👍👍

[@vishnuprasad556]

sir maine ghar banaya hai lekin chajje main latak beem nhi hai uske liye kya karna chahiye

[@DrPraveshSainiHomoeopathy]

best knowledge sir

[@NitinSingh0018]

Knowledge full video 🙏

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@kalpanarai3406]

तीन फुट चौड़ी 15 फीटलंबी बालकनी बनाना है । कैसे बनाएं

[@arunkumardesai7223]

Thanks for helping me Dada 🙏

[@RAJUBESU]

Can we used as shifting of centre point of columns by hilty?

[@nehemiaharrolla6139]

Good information

[@RajivKumar-qb7ji]

How much cost this 04 Nos Anker bolts? (size as per vedio). How much cost of M. S. Plate? (Size shown in Vidio)

[@sarkarpinaki1]

Very informative video.

[@chanakyasinha8046]

Nut nikal ke thok sakte hai thread pe asar nahi ayega

[@nationalfurnitureandinteri4763]

Very nice video sir

[@Arifview3333]

Bhai ander iron road aygaya hai

[@saurabhhadke9009]

Thanks sir for this informative video

[@premjha7722]

Sirjii flexural test ( Beam ) test kaise karte hai aur vo karne ka reason kya hai uska video banayiye na

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@kashi2843]

excellent video sir, please tell me is there any Indian counterpart of the anchor fastener BETTER or same quality of Hilti fastener used in civil engineering by professionals - pls tell name and model no OR all only use Hilti ??

[@TEJARAMCHOUDHARY88]

Mujhe aap se bat Karna hai

[@MukeshBarman-f2c]

Plate kaha milega

[@civilengineeraltaf5759]

Aap sath me ye bhi batadete ke eska uses kya kya ho sakta hai........

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@RamDas-vg4xb]

Shearing load is column?.. column only take axial load and moment due to eccentricity….

[@gopalkhilwani6023]

Sir 4" ki purani chat ki load capacity kaise badhaye

[@dukaleashokdukaleshravan2029]

Drill size kya chahiye

[@prakashnayak869]

Really knowledge full

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@AmitSingh-th1ir]

Sir ye fashner कितने के ओर कहा से मिलेगा?

[@avinashdubey751]

Contact me

[@hariompathak3464]

Pull out test pe banao sir

[@subodhanand8271]

रॉड आएगा तो क्या हॉग?

[@RaviMode-mv1xo]

Good job

[@shivaprasaddesai2805]

Hole ke jadah rod mile to kya kare

[@rbsinghcivilengineeringaca6777]

Hole ka location shift Karna hoga..

[@rbsingh7442]

Very good knowledge.

[@bharatvora1628]

Supar sir Kabhai hamari mula kat kare...

[@pravinahir2296]

Sir isane kase decided kiya ki 120 jana chai

[@rbsinghcivilengineeringaca6777]

Dear very good question, As per Anchor Bolt Fastener technical specification, already minimum depth of Anchor Bolt given & already marking in Anchor Bolt minimum requirements depth, but different Dia wise depth & strength change hogi ish liye aap ki requirement ke anusar aap ko anchor bolt use karna hai, aur video mein bhi depth ke bare mein bataya Gaya hai

[@Mghosalkar]

Great sir ji Jay hind vandematram

[@Rabiya-fabrication]

1000 kg vajhan jhel sakta hai sar 2:53

[@adityasehgal4123]

मकान बनने के बाद 2मजिँल पर बालकनी कैसे बनाऐ

[@rbsinghcivilengineeringaca6777]

छज्जा की सरिया को एक्सपोज कर के steel को welding करना है उसके बाद आप को horizontel beam ka support भी देना होगा sir ji . यदि बालकनी की लंबाई और चौड़ाई ज्यादा है तो .. और यदि स्टील की बालकनी बनाना चाहते हैं तो एंकर फास्टनर बोल्ट लगा कर भी आप कर सकते हैं..

[@GovindSingh-yv7tr]

Your thumbnail photo looking like me.

[@ykjoneja4661]

Well explained

[@C.RONALDO-cr7-s]

जैसा एंकर बोलते हुए बता रहे हैं कि एक बोल्ट टाईट करने के बाद क्रॉस में उसके सामने वाला बोल्ट टाईट करना चाहिए लेकिन वीडियो में जो व्यक्ति बोल्ट टाईट कर रहा है वो ऐसा नहीं कर रहा है इसलिए आपको पहले अपने इस साथी को भी ट्रेंड करना चाहिए।

[@premjha7722]

Concrete mix design with step calculation ka video banayiye please sir

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@yashvantmakwana6129]

Very good

[@shambagel]

Please make video of staircase bhim making for load balancing old bulding

[@satyanarayanroy8294]

Bhut hi achha hai.

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@arun07777]

Sir mujhe yahi bolt hona hai iski online buy ki link de do sir

[@rbsinghcivilengineeringaca6777]

Dear Apne neerrest hilti dealer se baat kariye aapko har EK prakar ke Bolt provide kar dega aapke load ke according..

[@arun07777]

@@rbsinghcivilengineeringaca6777 ok

[@sanjayvadoliya8598]

Nat tait me ring spanner👍use kare

[@imdadimmu8741]

Very helpful video

[@ronil_singh]

Use chemical also for fastener ensuring extra grip

[@SudebMode]

Good job 👍 Good is good 24 Mater H Bim available hi please message

[@nirmalchaudhary1251]

What is the use of insert plate? Plz in next vedio🙏

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@surajverma7442]

Thanks upload video

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@TEJARAMCHOUDHARY88]

Mujhe bnana hai Bhai

[@sandeshkirve1388]

Fastnor fitting karate samay bolt ke pichale hisse par hammer karana hai ye to nut pe thonk raha hai. Fitter ko achhi training ki jarurat hai

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@RaviMode-mv1xo]

hello sar 12 Mater HBame video please

[@jadavhimat3010]

Pull out test ka video banaye na sir😅

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@SabirAli-ob6ou]

Very good.sir

[@manoharrgowda2572]

Sir any adhesives used inside the hole for bolt?

[@rbsinghcivilengineeringaca6777]

Not required dear ..

[@ajaynoraajaynora1191]

@@rbsinghcivilengineeringaca6777 moo m no noon ppp loo 8u

[@usmangani2975]

Supaer sir

[@maheeshkumarthapa]

Excellent performance

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@Clientfirst8237]

200 kg ka door bim ke sath laga sakta hai

[@sanjaydubey7791]

Excellent

[@anandkashyap4626]

सर हमको पता नहीं था शटर पति के लिए हमने कलम एक कोना काट दिया मुझे सुजाओ दे

[@imdadimmu8741]

Thanks for support sir

[@RajaKumar-hz6od]

इसको लगाने का फायदा क्या है क्यू लगाते हैं ये

[@subhajitpaul2848]

Proper bataye par proper dikhaye nahi.

[@piyushdhake3641]

Sirji🙏🙏🙏

[@civilknowledge7534]

RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc

[@Ahitesh01]

Nice