This Tamiya Crawler Went To 🤬💩! CR-01 Rock Socker. MY MISTAKES!

Рет қаралды 13,524

Күн бұрын

Пікірлер: 119

@garethcurtis9665 2 жыл бұрын

I have ran this kit as a full on crawler up against TRX4 etc with great results. The shocks (well system) are actually brilliant. Upgrades 1. Wheels & Tyres 2. Driveshafts 3. Motor for slow control. Also a great rig for 4ws conversion.

@philmoffett366 2 жыл бұрын

I've built dozens of tamiya rc's and this one was the one I made the most mistakes on by a long way! The best advice I can give on this rc is read the build manual before you build it then read it again and after you've done that.....read it again!

@peterwakinu3328 2 жыл бұрын

👆🏽👆🏽Thanks for Commenting👍Congratulations 🎊 You have been selected among the shortlisted winner's🥇 for the season Giveaway 🎄🎁 Message me Above To claim prize......✍️ ✍️✍️ ✍️ ✍️

@RCBirds 2 жыл бұрын

So right Gavin, it's not a typical Tamiya build. But somehow it's a very refreshing build. Taking time and checking the manual many times is mandatory. And screws... so many screws. But I loved the build of my Unimog and I would like to do it again. Maybe on a high-lift or semi. Nope, it's not your fault. Many builders had issues with the middle gear. You need a lot of attetion for this part and even then it's not guaranteed that it fits.

@tomlucasrccrawlers9108 Жыл бұрын

I l9ved everything about my CR01 except the steering and Driveshafts. Very cool and unique crawler. Loved the over-complicated suspension and that crazy tough transmission.

@michaeldorich4485 2 жыл бұрын

I can see where this build has a lot of parts that could easily cause some mistakes when you're under time pressure. I think it's a great service for other builders when you show us your mistakes. Keep up the good work.

@All_RC_Fun 2 жыл бұрын

Thanks for the advance warnings of ⚠️ on this chassis build.

@teamsmitsrc9396 8 ай бұрын

Suspension of and 4 axial shocks i did on mine. Now it gets the laro d90 body .

@eskor-h3518 2 жыл бұрын

I made some same mistakes and some diferent. Have fun with the servo. Hope that you have the right servos my one's didn't fit with the servo bumper.

@AddamsPlayground 2 жыл бұрын

Those little blind nuts in building the frame can be frustrating. I got annoyed with them building my CC02! So many fiddly little bits to get together all at once! It looks good and I agree, the Bronco is the coolest looking of them!

@misterrottweiler 2 жыл бұрын

I've got a Rock Socker inbound, love how candid you are with the mistakes, and very helpful to have these to look out for when I get to build it

@RCKickschannel 2 жыл бұрын

Enjoy! 👍🏻👍🏻

@misterrottweiler Жыл бұрын

I actually had that same gearbox closing issue lol You we’re right about the centre shaft pin, but when it’s actually in its slot, it can still then slide out and prevent the bearing seating back fully, I spent close to half an hour before I spotted it. Why the pin location doesn’t just fully retain the pain I can’t imagine, but that’s what I suspect happened to you too (apologies if someone else has already put this in a comment). Easily my most challenging Tamiya build so far 😬😅😎

@rc-dom-uk 2 жыл бұрын

Ya got there mate. Looks awesome and I like the body swop idea

@agevan6735 2 жыл бұрын

Mate, cool vid, we have all had to back-track on builds, haha thats part of the fun, Cheers from this Aussie in China!

@michaelqendro9825 2 жыл бұрын

You could hold those captive nuts in place with a small blob of rubber cement. That was recommended on the CC02 Unimog build.

@powersmodelgarage 2 жыл бұрын

Great build video. Mistakes are just part of the fun 🤷‍♂️

@ajkim1124 2 жыл бұрын

Mistakes help us learn

@duncanmarriott2052 2 жыл бұрын

Bronco is #1 in my books too ! I've got the FJ & Socker but had to order a real Bronco for Christmas . Built this week waiting on a train ride to California . Merry Christmas !

@RCKickschannel 2 жыл бұрын

Nice!!

@rcgeneration824 Жыл бұрын

Back when I was building the broco version, I myself made a ton of mistakes. But when it was all completed along with painting the body in black, I regrettably sold the darn thing! It never set foot on dirt.

@Pablo668 2 жыл бұрын

Ugh, I've been there on the mistakes score. Sometimes it just takes time to revisit the manul and get things right.....several times over..cough! ahem!

@lo2713 2 жыл бұрын

Looks a funky suspension set up for sure, looking forward to seeing how the body turns out 👍

@Triggered-RC 2 жыл бұрын

Upgrade the shocks for sure. Also, the hardened steel axles with diff-locker and hardened steel drive cups are a good choice. If you do that, then add steel drive shafts as well.

@jezgregg2172 Жыл бұрын

I think im gonna get one of these next as it will look nice next to my blackfoot and twin detonators. Have you built any of the tamiya quadtracks Gavin? As I'm thinking of modding them for a custom 3d printed project.

@adrianharrison5208 2 жыл бұрын

It's definitely one of those builds we're I had to read the instructions a few times over and I still made quite a few of the same mistakes as you, those captive nuts nearly got a small dab from the hot glue gun 😒 as you know they like to fall out.. All in all such a cool different build from Tamiya and one I glad I bought

@brianargo1659 2 жыл бұрын

Wow how long has it been since we got a video of more than just a few minutes from RC kicks? Cool build!! Can't wait to see the finished product

@peterwakinu3328 2 жыл бұрын

@maxpaul11 2 жыл бұрын

Silly Billy! Haha 😄 🤣 😂 😆. Another great video brother! Love that you included mistakes made building up this awesome model! Cheers 🍻 Follow directions 😀

@RCKickschannel 2 жыл бұрын

Glad you enjoyed it

@aaronlim6365 Жыл бұрын

Make a review if body shell of hg 407 will fit to this chasis frame

@mitsuman5555 2 жыл бұрын

That shock setup is wild.

@peterwakinu3328 2 жыл бұрын

👆🏽👆🏽Thanks for Commenting👍Congratulations Fan 🎊 You have been selected among the shortlisted winner's🥇 for the season Giveaway 🎄🎁 Message me Above To claim prize......✍️

@darkstorm303 2 жыл бұрын

The Bronco one looks sweet 👌

@peterwakinu3328 2 жыл бұрын

@prophetate 2 жыл бұрын

Hahaha oh well everytime when this happens to me I always say well I get to practise a bit more for the next time 😇😊❤️❣️ also I agree regarding the 1973 Bronco body I love that, so if possible get that body for this chassi 😊👍

@RCKickschannel 2 жыл бұрын

I’m not sure, I’ll have to look and see if it’s still available

@prophetate 2 жыл бұрын

It should be available I bought one tamiya 1973 bronco body quite recently for a smaller MST CMX crawler I bought. I think I bought it from Tamico. Let me have a look see if I can find it available 😊

@prophetate 2 жыл бұрын

@@RCKickschannel it seems you might be right 😞 the 1973 Tamiya Bronco body seems hard to come by, if I find I’ll let you know the 2021 ford bronco seems to be available though 😊

@richardhawkes7904 Жыл бұрын

Hi Gavin. Great video as usual. I made similar mistakes that I had to sort. I am still suffering with lack of suspension travel before the linkage hits the chassis. Any advice what to look at.

@RCKickschannel Жыл бұрын

Did you do the zip tie trick for the suspension pivot?

@richardhawkes7904 Жыл бұрын

@@RCKickschannel no I didn’t try that. I’m not really sure what it is.

@andyrobinsonrc2480 2 жыл бұрын

Really wanted Tamiya to put a defender body on this chassis at the time but it’s on the cc02 now so I’m good ;) besides that it’s a cool chassis. As for the mistakes everyone has builds like that at some point. Good to see you show what went wrong :)

@peterwakinu3328 2 жыл бұрын

@RCKickschannel 2 жыл бұрын

I’m sure you could get the defender body to fit this chassis. I’ll try mine today for fun and see.

@rivierarc 2 жыл бұрын

Really like the look of this! I love the look of this body as I think it suits it. As for other bodies, that could open up a lot of opportunities 😁

@canuckchuck8836 2 жыл бұрын

For me the transmission problems were caused by not pressing BD7 and BD16 onto the sun gear. I had to seat them with a hammer and socket. Did you have any issues with the diff-locking pin? In my kit, when it was installed it forced the mesh of the crown and pinion gears. I gave up on the pin and inserted a spare bevel gear in each diff.

@RCKickschannel 2 жыл бұрын

I’m not sure what it was to be honest. I messed around for so long trying everything. It was only when I dismantled everything and rebuilt it did it fit correctly.

@stephenwiddick4934 2 жыл бұрын

It is a more complex kit but I made no mistakes while building mine. I've got a ebay jeep hardbody on mine complete with interior. I needed to put internal springs in rear shocks due to the weight. Lost a small amount of articulation.

@RCACTIONAUSTRALIA 2 жыл бұрын

Looks like a different build Gavin 😊

@RCKickschannel 2 жыл бұрын

Yep it was that Adam. 👍🏻

@massimolooman1445 2 жыл бұрын

A very nice one Gavin👍 I made almost the same mistakes. The cheapest MOD I have done is to zip tie the suspension reaction arms to eliminate the play. Also did other shocks, driveshafts ,drivecups,bearings, weighting the wheel,difflock,HW crawler brushlessmotor and four-wheel steering.

@peterwakinu3328 2 жыл бұрын

@SuperLowVoltage 2 жыл бұрын

The motor plate is directional. It has a recess around the hole on one side. Also, watch out for the 5mm E clips versus the 6 mm E clips. I know this now.

@neilstothard 2 жыл бұрын

Having not seen one of these run it will be interesting to see if you need to change the motor to a bigger turn crawler one.

@RCKickschannel 2 жыл бұрын

I was thinking that as well Neil.

@h-jg7730 2 жыл бұрын

Its almost like building a Ikea cabinet whit out looking at the manual before 😝👍😂

@peterwakinu3328 2 жыл бұрын

@IowaBudgetRCBashers 2 жыл бұрын

I’d like to have the 73 bronco version.

@peterwakinu3328 2 жыл бұрын

@RCKickschannel 2 жыл бұрын

It’s a good looking body

@tm5123 2 жыл бұрын

Might work to put stiffer oil, smaller hole pistons in the shocks, to alleviate the wobble more, I guess. I got one I still haven't assembled, so no real experience with CR-01. But sure is a pretty thing, even tho it's not really capable as a crawler compared to the modern stuff.

@RCKickschannel 2 жыл бұрын

Yep it’s cool looking for sure.

@t-money561 2 жыл бұрын

its a jiggly rig for sure, but those shocks wont help, its the spring setup, its just designed that way, its a surprisingly good setup, very not-scale which is kinda tamiya

@peterwakinu3328 2 жыл бұрын

👆🏽👆🏽Thanks for Commenting👍Congratulations Fan 🎊 You have been selected among the shortlisted winner's🥇 for the season Giveaway 🎄🎁 Message me Above To claim prize......✍️

@liamRC5487 2 жыл бұрын

The shocks will probably be ok when the battery etc is in. Good build

@peterwakinu3328 2 жыл бұрын

@bespincustompropsbombarta8300 2 жыл бұрын

You appeared to be having a bit of a mare Gav 😂

@RCKickschannel 2 жыл бұрын

All my own fault. Tamiya did use ever different bolt length in this kit mind, so that was starting to become frustrating by the end.

@darrisbrown7516 2 жыл бұрын

Really good tuff 💪 build! People don't build up kits a lot anymore with the RTR that are out now. At least new comers just my thoughts. Love it looks very cool 😎 👌

@peterwakinu3328 2 жыл бұрын

@MrJoffster 2 жыл бұрын

Cracking video gavin now I have a dilemma I was going to pull the trigger and buy the clodbuster but now I've seen this I'm tempted with this rocksocker kit instead oooh decisions decisions 😀

@RCKickschannel 2 жыл бұрын

Rock Socker is a good looking chassis for sure. Thats a hard call Joff.

@MrJoffster 2 жыл бұрын

@RCKicks it definitely is gavin the clodbuster has so many option and upgrade parts carbon etc but as you say the rocksocker is.a brilliant looking chassis

@rcgeneration824 6 ай бұрын

The one mistake I made in building the CR01 Bronco, was that regrettably I sold it without even running it once. 😭

@peterjohnson9243 2 жыл бұрын

Rock Socker Shocker, easier said than built!

@peterwakinu3328 2 жыл бұрын

@peterjohnson9243 2 жыл бұрын

Message you to claim my seasonal prize! You don't want my bank details do you Gav!!!!????

@alfredyost7972 2 жыл бұрын

Tamiya makes a lot of metal upgrades for this kit. They make metal dampers and even the black side pieces in metal. Maybe they do not make those parts anymore. Thoughts?

@RCKickschannel 2 жыл бұрын

I haven’t seen the side plates in metal for sale.

@alfredyost7972 2 жыл бұрын

@@RCKickschannel The metal plates that I got were made by Tamiya. They probably do not make those anymore. I wonder if "Integy" might make them. I probably spelled the name wrong. LOL

@douggilreath1984 2 жыл бұрын

I messaged you with the fix for the slop in the suspension.

@peterwakinu3328 2 жыл бұрын

@RCKickschannel 2 жыл бұрын

Thank you, I will do that as it looks like a good little hack.

@richardhawkes7904 Жыл бұрын

What’s the hack please. I can’t seem to find many.

@duncanmarriott2052 2 жыл бұрын

Weighted wheels & Tires - Lock both axels

@peterwakinu3328 2 жыл бұрын

@roblowrie1969 2 жыл бұрын

That's a really good looking truck, especially, with that body on it. I don't know too much about this model. What's it designed to do? It looks more like a crawler than a monster truck, but whatever, it looks great. 😎👍🏻

@RCKickschannel 2 жыл бұрын

Yep it’s a crawler

@roblowrie1969 2 жыл бұрын

@@RCKickschannel ah, cool. My type of car then. 😎👍🏻

@smellurfingerrcdejesus9176 2 жыл бұрын

So excited come on Gavin you know that Tamiya makes the best instructions that's a rookie mistake starting off guys started off on a bad note that's what happened with my blackhead motor I wasn't paying attention and I put the pinion on the high tooth pinion and then I put it back and all my years were making noises and I was like what the heck it's cuz I didn't pay attention that's what I'm getting to random captive nuts put grease and hold them you know what I noticed about the car with the most mistakes you actually whenever you get it put together the correct way you have the most fun with their car cuz you were like you remember all the problems you had and then you see how it's supposed to go together and then it all makes sense that's beautiful beautiful mistakes

@peterwakinu3328 2 жыл бұрын

@smellurfingerrcdejesus9176 2 жыл бұрын

You know you should really leave me alone and if I win anything really in real life you're missing it up for me you're not the real RC kick can you please stay off of my comment

@fatfreddiescat9952 2 жыл бұрын

I’ve collected all variations of this chassis and even a GMade conversation chassis, this and the jeep body being my favourite of the bunch. A lot of the hop ups are best put in while building it up, but your right with the shocks. These should be first on your list to change along with the tyres and look at 4ws. There are loads more you can do with them to improve performance but start with shocks and tyres.

@peterwakinu3328 2 жыл бұрын

@duncanmcgregor7946 2 жыл бұрын

Not got a crawler and this makes me want to get one. Great looking and I bet fun to run over the rockery with

@peterwakinu3328 2 жыл бұрын

@SuperLowVoltage 2 жыл бұрын

If you go to 9.20 you will see black shading on the right hand side of BD11. This is all the clue you get.

@Cormano980 Жыл бұрын

They've might as well name it Sock Cocker

@douggilreath1984 2 жыл бұрын

I made all the same mistakes you did. 😆

@RCKickschannel 2 жыл бұрын

LOL 👍🏻👍🏻

@memememe2674 2 жыл бұрын

I do not want to sound rude to anyone but I do not see how anyone apart from a first time builder can go wrong on a Tamiya build, the manuals are the best around full stop.

@RCKickschannel 2 жыл бұрын

You forget that you have to read said manual. Obviously this is not always the case lol.

@liamRC5487 2 жыл бұрын

👍cheers I know nothing about this stuff

@RCKickschannel 2 жыл бұрын

Same 😝👍🏻

@countmurcielago9802 2 жыл бұрын

It’s got to be a brat body as a updated mud blaster

@RCKickschannel 2 жыл бұрын

Like that idea

@spiderjec 2 жыл бұрын

Not really an upgrade but to fix the issue. I have the land cruiser version, i upgraded most lower part to Aluminum or metal for lower center of gravity. kzbin.info/www/bejne/mn3Tfnqae7Caeac

@Logans_RCAdventures 2 жыл бұрын

Wish Tamiya made cheap RC cars. Can’t even find old junky ones for cheap anymore.

@RCKickschannel 2 жыл бұрын

Things have become extremely expensive for sure.

@nilsbundgaard466 2 жыл бұрын

I'm The first

@RCKickschannel 2 жыл бұрын

Yes you are NB :)

@mikeymike3240 2 жыл бұрын

Ehhh, body posts!!!!! DOH

@peterwakinu3328 2 жыл бұрын

@Craigstern73 Жыл бұрын

I guess to get lots of views you've got to explain everything, including mistakes, exhausting no thanks.

@liamRC5487 2 жыл бұрын

Hi. I've seen a request to contact you on telegram? Is that true?

@RCKickschannel 2 жыл бұрын

Scammer

@AlvarezAzel 2 жыл бұрын

We all have days like this so don't let it get you down. First upgrade should be some better tyres, the included ones are awful! too hard and not good for anything really.

@peterwakinu3328 2 жыл бұрын