Code List Included!! HOW TO Read OBD1 Codes Chevy GMC with paper clip!! heroboard - free music to free your mind • Shane Euston / shane-euston
Пікірлер: 149
@autumn_wind3x7932 жыл бұрын
Just what I was looking for. Paper clip hack much narrowed it down. Got code 54. Fuel pump circuit low voltage/EGR valve solenoid 2 error. Time to jack up the Van. Thanks Brother.
@tammysmart50853 жыл бұрын
Thanks for the video! Now I know the O2 sensor has a problem (code 13), on our 1992 Chevy S10.
@marzsit98333 жыл бұрын
keep in mind that these older obd1 systems are not as accurate as a modern obd2 system. just because you get a code that says you have an o2 sensor problem, don't assume the sensor itself is bad. a dirty air filter, an exhaust leak or a clogged egr valve can all set an o2 sensor code on an old gm vehicle. also, code lists not only vary from model to model but also year to year, and fault codes may have a different number.
@OldsmobileCutlass1969Va Жыл бұрын
Man... This video saved me! The parts stores and repair shops no longer carry/have OBD1 scanners anymore. I had a shop tell me they can't scan my car, but can fix the issue. I asked them how if they don't have a scanner to know what is wrong?! Now I have at least a general idea on where to start. I already have a parts car, so just a lot of trials to swap out to fix the problem.
@tommitchell8425 Жыл бұрын
Thanks to you sir for your informative video.Really helped me out on my 95 GMC SIERRA.
@abelesquivel40879 ай бұрын
Very helpful video with all the points covered. Thank you for this
@larryturley66352 жыл бұрын
Thanks for the help. I guess I used to know this back in the day. Haven’t messed with these year models for a long while.
@andrewwhitman45513 ай бұрын
Dude thanks so much just got a 1992 gmc SL 1500!! Appreciate ya!
@evilokc4 жыл бұрын
thanks for the clear video and instructions. I knew I could jumper an obd1 but I couldn't find any info on how to do it.
@codys96012 жыл бұрын
Thank you so much for this...can't wait to see what codes on my 95 s10..greatly appreciate this information
@buffdiggy5 ай бұрын
Does your s-10 have the newer shaped obd2 plug or the rectangle. wondering if it worked for you.
@codys96015 ай бұрын
Try to find forums for your year make and model on Google for wiring diagrams or any information regarding the prongs in that OBD port....If you have an obd2 tho I believe your better off getting a cheap scanner that gives you diag readouts
@neonvoid Жыл бұрын
On the top right of the connector, connect the two pins (top right 1 and 2). There, you saved 8 minutes.
@mattr36325 жыл бұрын
I'll give this a try. Haynes said to jump A & H, but that didn't give anything at all.
@aaronpayne4782 жыл бұрын
For anyone who has a repeating 1.1-2 code after the initial three, that indicates you have no codes to read.
@Nickk.amador2 жыл бұрын
How could I get it to read a code I keep getting that 1.1-2 code
@aaronpayne4782 жыл бұрын
@@Nickk.amador that means you don’t have any codes then
@Nickk.amador2 жыл бұрын
@@aaronpayne478 it’s really weird because my truck is sputtering in first gear when I floor it ONLY IN FIRST GEAR truck drives completely fine under regular throttle but I’ll floor it it’ll drop to first gear then sputter it’s ass off curt off the radio and flash the seatbelt light and the engine light but I can be full throttle in 2-3 just fine
@FortniteIsAnAI2 жыл бұрын
What if it doesn’t flash at all???? I have a 1995 c1500… 350
@aaronpayne4782 жыл бұрын
@@FortniteIsAnAI I would say try again and make sure the key is in the correct position
@marciorocha4656 Жыл бұрын
thanks for the help.. i'm from portugal and i have a gmc s15 jimmy from 1989
@mindexpansion11115 ай бұрын
This was extremely helpful! Thank you
@joshakers13 жыл бұрын
So if it just keep blinking 1... 1,2 then does that mean there are no codes being sent?
@Kapnez2 жыл бұрын
thanks man i like these trucks to.. lack of maintenance is what i find the most,,
@alexanderporto93102 жыл бұрын
“Pop that in like this” continues to show it not torwards the camera
@chevygirl63732 ай бұрын
That is a Beautiful truck ♥️
@brobean9509 Жыл бұрын
Thanks can’t wait to see what my truck shows!:)
@joejohnfanning16376 ай бұрын
Thank you your video helped me out quite a bit
@joejohnfanning16376 ай бұрын
Code 13
@curtiskoutzun53942 жыл бұрын
Thank you I have an older car with obd 1 and only obd2 device. Very helpful.
@SonnyThomasShow13 жыл бұрын
Awesome simple trick. Thanks 😊
@cousteaufan Жыл бұрын
Great content! Very useful and well explained.
@miguelplascencia60933 жыл бұрын
My truck has a small misfire at idle I've been driving it like that for about 8 years I'm tired of it I have no codes never gotten a check engine I pass smog i live in California I have rebuilt the tbi ran fuel injector cleaner changed the fuel filter twice changed the distributor spark plugs and wires I just can't figure it out I gets worse as the truck warms up, when it's cold start it sometimes misfire like every 5sec maybe 10sec, but once the truck reaches operating temp my passenger seat is vibrating like crazy
@zephead48353 жыл бұрын
Check out KZbinr Scanner Danner he's the best
@hardyb31110 ай бұрын
Needed this vid bought a actron scanner for my 94 lesabre and the scanner end was too big to fit on the plug.
@adventureslim401611 күн бұрын
How do you clear them?
@jonahjohnston69092 күн бұрын
Or you could go to O'Reilly's, they have an OBD1 scan tool
@lht5dy3111 ай бұрын
So my service light came on, shit it off. An didn’t come back on. If I were to do this, I would imagine it would show a possible code with a potential problem?
@stevenrath46624 жыл бұрын
I get a code after driving about 5 miles. Code goes away when the engine is off. Would it show a past code? Does this trick work with the engine running?
@stevenrath46624 жыл бұрын
The trick still works! It showed me 2 codes, even when the check engine light is not on. So, still do it and you will see your codes.
@Mr.Beastforpresident4 жыл бұрын
What oil y’all running? I hear some have flat tappet engines. Meaning the oil needs higher ppm zinc
@danielnapper15725 жыл бұрын
so are the same codes for all chevy 350 engines
@nudrummr3 жыл бұрын
The range starts from 88-94
@cathydaydif70894 жыл бұрын
We appreciate your skills. My husband did exactly what you said and it did not come up with a code. Just the same start lights over and over again. The suburban still does not stay running. Do you have any suggestion?
@codybirchfieeld14473 жыл бұрын
Keep on trying you'll get it And be better and tougher and smarter for it And probably more ticked off but that's how it is
@erniekoch8646 Жыл бұрын
Fusable links tostarter sienoid prmary hot wire
@kanadianbacon7733 Жыл бұрын
*"You need to have the 'Enhine Service' light on the dash when fist turning the key to 'on'"* Mine didn't!,...problem was with the brake switch to the computer not sending proper 'Signal'!,Sooo... *"Jumped Pink 'n 0range wires @ brake switch...'Boom'!... Fired right up as the Computer got the information to then send fuel to TBI!♡¡"* >Next , I wired up a proper switch in same area. *"Cheers!¡"*
@kanadianbacon7733 Жыл бұрын
You need to FIRST have an: *" 'ENGINE SERVICE' LIGHT ON THE DASH!"*
@mrperfect81244 ай бұрын
I seen the 52 code but i dont understand the ONE, ONE TWO part. ??
@alleighdobbs63192 жыл бұрын
What if it doesn't work? Mine doesn't even have the a b part, there's only three on the top and one on bottom...I have a 95 tacoma
@jellojiggle15 жыл бұрын
Excellent tip. Worked just great for me on 2 vehicles. Thnx.
@DeadXDread Жыл бұрын
Can it store multiple codes.? Is there a separation
@RichardBack-hr9xw6 ай бұрын
I have the fault codes but can't find what they mean. Anyone have a list of codes?
@reagan5133 жыл бұрын
Good job, got a 1993 S10, tks again.
@fabianheuver Жыл бұрын
When doing this to my firebird the front fans turn on and it just keeps on flashing 1 12 without any difference in pauses anyone a clue or does this just mean there are no codes?
@aclegacy72 жыл бұрын
Is this method can work on a GMC 1995 gas topkick c7000?
@josecfish52974 ай бұрын
Can’t find this port on my 1973 gmc truck?🤷♂️
@SamsAutomotiveS3 жыл бұрын
Thanks man..good job
@Rockkickers2 жыл бұрын
Does that work on older 80’s Chevy cars too?
@kimsmith5083 Жыл бұрын
Are those codes same for OBDII
@miguelgudino97954 жыл бұрын
Does it works on a diesel 95 chevy suburban?
@ME-jc7xi2 жыл бұрын
That was fantastic. Thank you!!!!!!!
@ManMak66 жыл бұрын
Wow Larry you’re so smart 🤓
@nudrummr3 жыл бұрын
I'd like to think this comment was you being sarcastic.
@saulgalarza5669 Жыл бұрын
What about abs codes?
@SeanMckanna3 жыл бұрын
Thank you.
@christophermarker78583 жыл бұрын
My S-10 1994 is not showing a code, just the 1 & 2 telling me its active, but it cranks but wont start. Have any idea what that could be?
@dennisdoran39472 жыл бұрын
Maybe the ignition coil or the plug on the bottom of the distributor don't remember the name of the part
@MustangGuru Жыл бұрын
Does not work on some 94 year GM models. OBD 1.5
@colossalko3 жыл бұрын
How does this change for a 16 pin connector?
@freddythonon21224 ай бұрын
Niiice, thank you
@usedcoma94612 жыл бұрын
Mine just flashes when I do the paper clip
@dano45722 жыл бұрын
where did you get the code# sheet from??????????????????????????????????????????????????????? all of this doesnt help without that code# sheet.
@mandaclark723 жыл бұрын
Can i do this on my 96 cavalier its obd1
@shuglovemagnolia66504 жыл бұрын
What if there was another code besides 51?
@bigtuna95292 жыл бұрын
After it showed code 51 three times it would go onto the next code instead of that one to one two (1-1,2simply means the test is over) if there was another code after it showed code 51 three times then you would count the flashes again and that would be the second code when all the codes are read it will flash that 1…1,2 to showing you the test is complete
@johnnyrodriguez2443 жыл бұрын
Tried this and I get the (1..1.2) start sequence over and over. Never gives me a code sequence.
@Nathan-u2g3 жыл бұрын
same
@marc-andrebourget23113 жыл бұрын
Same 👋
@johnnyrodriguez2443 жыл бұрын
Did you figure anything out? Did it ever give you a code? Well I went to drastic measures. I tore my engine down to the block and in the process of rebuilding it. That should eliminate the wrongs, I hope.
@bigtuna95292 жыл бұрын
You may not have any codes also this will NOT work on GM vehicles from 1994-95
@rubalcava19842 жыл бұрын
Has anyone gotten a code 82 on a 94? And what was the issue?
@hankbridges50555 жыл бұрын
Can I use a Ford gem-clip or a Chrysler gem-clip?
@willubhave54 жыл бұрын
thats all I got is OBD 1 vehicles...the paper clip is useful but I got the actual key for the A and B ports...
@markthompsoncpa3 жыл бұрын
That truck cost you $300??
@erinautumns238 Жыл бұрын
Did nothing for my 83 caprice
@felixmikkialmosttoasted39114 жыл бұрын
Thanks. I havent done this in 25 years on a 85 Monte Carlo SS. Have just bought a 93 Yukon 2 dr with a code that popped up.
@chevy66driver2 жыл бұрын
$300!? I feel bad for the old widow you tricked into that deal!
@armarx7362 жыл бұрын
Very good info.
@84SS9312 жыл бұрын
Would this method work if you have aftermarket digital gauges?
@lowlife_corona14773 жыл бұрын
I have a code 12 on my 89 chevy k1500 can anyone help??
@thalfis5 жыл бұрын
Rock on, thanks for making it easy!
@OldsmobileCutlass1969Va Жыл бұрын
Also, today that truck he bought for $300 sells for $3k now...
@ricky-sanchez Жыл бұрын
Lol I'm also here recently trying to figure out how to use obd 1 to find a mis-fire. I think it's my crankshaft position sensor, but I don't want to replace it until I'm sure.
@zulukono6632 жыл бұрын
OBD2 started in '96.
@elden_lore_title4 жыл бұрын
Mine doesn't show any check engine light when it's on acc but when I start it and put a paper clip and it starts flashing or blinking without stopping. I read online that this usually means a misfire is that correct?
@justinwoosley31883 жыл бұрын
Mines doing the same,
@Super-J103 жыл бұрын
$300 ??? Auction ?
@tommavrakos2 жыл бұрын
Key on or off??????????
@ajtimpe5 жыл бұрын
Cool
@maxleader87457 ай бұрын
Three hundred dollars you should have got two of them
@davekarlen65913 жыл бұрын
where u get those codes from just see the blinking light 4 a few times?
@Faithful9er4L Жыл бұрын
Thank u sir
@jojozepofthejungle26554 жыл бұрын
Don't have one of those. Mine is an 89 commodore and it has a white diagnosis plug under the dash, with only two ports, I think it's connected to the ICU chip. Just trying to find the video I watched.
@robertgreatsinger91792 жыл бұрын
Yay ! 93 cc heavy with catalytic converter gone, 02 hanging.... Code 13.... Any one got a spare to sell ?
@JosephLorentzen5 жыл бұрын
What about an ecm that sets the Check Engine light but does not send out even the diagnosis mode 12 .
@nickpietrzyk45655 жыл бұрын
Did you ground it with the key in the ON position?
@kiyoponnn5 жыл бұрын
Nope you short it first when the car's off. Then turn the key to the ON position
@Mr.Beastforpresident4 жыл бұрын
InfiniteLoop Will it work on 1994 models?
@kevinguardian51195 жыл бұрын
5 ports? I see 6
@jellojiggle15 жыл бұрын
Curious. If there is no Check Engine light on and you use this procedure would it still blink the 1-2 x3?
@hankbridges50555 жыл бұрын
It'll blink to show a pass code. Get a small black code tester from Amazon or EBAY for G.M. cars. Follow the instructions on it. The bulb can be burnt out if it don't light up with the key- on engine off.
@JOEDAPOPERAPGOD5 жыл бұрын
Haemosu l 12 code is nothing it’s normal
@goldwolf06062 жыл бұрын
2:42 skip all his mumbo jumbo
@aladwanit2 жыл бұрын
1982 doesn’t have all the stuff you talked about.
@bubbasutton2803 жыл бұрын
I have a 1985 s15 gmc with 2.8L is hard to start it will start and die for a few times until it hit the right spot
@xhambonegaming26944 жыл бұрын
Is it safe to do it with the paper clip
@aleksandrzhila88655 жыл бұрын
thanks man
@missbrunetka16 жыл бұрын
Sooo interesting .. but good thing I have a husband to do all these things for me!
@4mbpswifi8045 жыл бұрын
Do you have any sisters😐
@joeponder96684 жыл бұрын
Alena Manuylov, so why would you and not your husband watch?
@ricky-sanchez Жыл бұрын
You pay the piper at bed time.💪
@TheAkstewie9 ай бұрын
Sure fucking wish a clean one was only $500 LOL LS SWAP THE WORLD! lOl
@markbond253916 күн бұрын
It is unclear what your dad is uplugging while you are removing the paperclip
@INTERNA93 жыл бұрын
WOW
@Neilster994 жыл бұрын
I get a code 78 any ideas
@Mr3X7R3M34 жыл бұрын
this wont work for 95. Gm switched to obd2 ports but still used obd1 computers... Do not jump pins 1\2 for 95 cars. Look it up and jump the correct pins
@JacobStayViben4 жыл бұрын
Mr3X7R3M3 so can i purchase a odb2 scanner and can a 95 impala and still get codes
@jamaljamal61693 жыл бұрын
Why wouldn't you just tell us?
@Mr3X7R3M33 жыл бұрын
@@JacobStayViben no... 1995 GM cars still used OBD-1 computers that can’t be read by new (cheap) scanners. You need to find an OBD-1 scanner and get a converter for it so that it plugs into an OBD-2 port........... yes, it really was a stupid move by GM
@Nathan-u2g3 жыл бұрын
ours just keeps saying 12
@marcus187806 жыл бұрын
What fixed code 51
@francispiligrin63495 жыл бұрын
5555'
@giancarloberlingeri38254 жыл бұрын
Buying another truck for $300.00
@jamaljamal61693 жыл бұрын
Didn't work for me. A weird fan like sound comes on though.
@OBS-Kev1991 Жыл бұрын
300 Bucks...I wish.
@dougbillman23333 жыл бұрын
Who taught you how to count... not 10 or 5... there's 12 and 6......