How to Install AMP Research Power Step on a 2020 Ram 2500

[@louisasians7938]

The best detailed installation video by far on KZbin par none. I have watched countless other videos before attempting my own. This one takes the cake.

[@reinaldocerdeira8590]

Thanks for the video. Can you please explain why you didn’t install the front spacer ?

[@CDL_ESQ]

I moved the right side step so the end cap (of the rear mounted idler) is at the mounting bracket...so about 3/4 of an each from perfectly centered. After this adjustment I did not have any interference from the pinch weld (it was hanging-up previously at the radius of the pinch weld bend ).

[@rosedalepaint]

Great video! I have the original powerstep with only the one motor on the rear, driving both the rear and the front linkages. The motor is acting up not extending as far as it should on the rear, but allowing the front to, oddly enough; partially because the rocker panel has corroded in the front and only has the top bolt holding it up, allowing the front linkage to swing, and the board to be cockeyed. I'll be installing another rocker panel to fix this. After a few times of this, the running board popped of at the rear only. What I noticed is that the sliding back plate with the female threaded holes for the allen set screws didn't have any threaded female holes, just a flat piece for the set screws to push up against, which again seems odd as the ridge that the running board sits in doesn't seem wide enough to offer resistance for the allen set screws to tighten up to. Has anyone experienced this as well?

[@emilyscandycakes4530]

Does 22 2500 ram have factory plugs for these step ?..i see 2 capped plugs

[@KenMansfield-e3t]

Will this application work on the 2021 Ram Power Wagon? I have been told that there is something under the body that wont allow the XL to be placed.

[@NoInformation-nr3eq]

air tank/pump, you can relocate it

[@_WELDR_]

Great video 👍🏼 installing yourself will save at least a couple hundred bucks. Plus you’ll do it nice and how you want it done ! I hade LINE-X install mine and well long story short I had to re wire everything do to wires were all over my engine bay 🙄😬

[@goducgo]

One of my steps won’t go back up. Fuse is good lights work. Any ideas?

[@certifiedtreespecialist9852]

At 18:42 was the lifesaver moment 😂😂

[@VietLe-USA]

Thanks for the detailed instructional video, the best on KZbin regarding AMP Research installation. Although mine is the Tundra, I learn a lot from your video.

[@djcallioux2635]

Can you touch on what you did with the pinch welds I've done a hundred of these dodges and the pinch weld always causes the step to hang up are you grinding the pinch weld also there has got to be a better remedy. I've even started building stoppers so the step don't go all the way up

[@marchuffman8266]

It hasn't been a dodge for over a decade

[@djcallioux2635]

@@marchuffman8266 ok. Ram

[@kodiei5819]

kzbin.info/www/bejne/f4XFcpifrbt-mrM

[@Ahleen0]

هل تعلم اين أجد التروس الدآخليه لمحرك دعسه يوكن دينالي ٢٠١٤

[@navymark101]

Great video, I'll be ordering those for my 2021 RAM 2500 in the next few months. I like the looks of your 2500, what size tires and brand are you running on that beauty and lift/ level. Thanks for the info, Navy Mark...

[@Realtruck]

Hey Mark! On our Ram 2500, we have the Supreme Suspension 3in leveling kit with 37x11.50 Nitto Trail Grappler M/T tires.

[@garcia1283]

Is there a way to wire it up without using the OBD II?

[@Realtruck]

Hey there! Unfortunately not, but Amp-Research also makes a pass through harness that you can use if you want to also run a tuner/monitor or anything else that requires an open OBD2 port. :)

[@danlanious8705]

Is there any reason these won't work on a gas 2500?

[@Savage1Living]

I installed them on my 2017 Ram 2500 6.4 last february no issues.

[@juliancortes3379]

Thank you for the video. Unfortunately my amp steps are giving me fitment issues, they keep getting stuck inside the pinch weld.

[@Realtruck]

Sorry to hear that :(

[@EduardoLopez-xk3dk]

Did you figure out the problem? I am currently having the same issue

[@heathpalmer4283]

Have you tried the bounce technique?

[@kodiei5819]

kzbin.info/www/bejne/f4XFcpifrbt-mrM since real truck can't read

[@larrytolentino7909]

Did you need to trim the pinch weld

[@kodiei5819]

kzbin.info/www/bejne/f4XFcpifrbt-mrM

[@johndormady880]

Thanks for the video. It was great help today.

[@hydro_rebel7741]

Ugh I want to put a set of these on my rebel but seems like more time than I would have.

[@Savage1Living]

Do it. You can do the install one step at a time as you see fit. That is what I did. One day I did the first step for all 4 corners i.e. installing the bracket inside frame, doing the pop rivet, and nutserts. Took about 20 minutes. Next day I bolted the mounts/motors/steps on. Took about 30 minutes. 3rd day I did the wiring. That took a good 2hrs. I took my time, strategically routed everything under the hood/firewall.

[@FredetteShawn]

Excellent video

[@nevarezfamily9291]

Thank you for the video!