Rebuilding an Engine in 30 Minutes! - 1JZ-GTE Engine Rebuild Speed Run!

[@aydanstallard4865]

you had that socket on a hell of an angle, I'm not surprised you rounded it.

[@Taterrrrrrr]

Also he should be pulling on the breaker bar to loosen instead of pushing. You get more power from pulling 👌

[@SAMMIT]

Yes

[@lolermount4271]

@@SAMMIT For the future, is a good habit i use professionally, to hit with hammer the socket, to have well embedded. I´m not surprised of the loosen pin, is only the head of the bolt welded to the surface, i see million of times.

[@jamesp3298]

Hey mate, when undoing the head bolts, put a little valve grinding paste into the hex void of the head bolt. It increases the grip of the tool into the hex drive and reduces the risk of stripping out the head of the bolt. We used this method on Subaru cam pulley bolts for years. Believe it or not, it actually works really well. Greetings from Queensland, Australia. 🤙🏻

[@SAMMIT]

Thanks for the tip! 👍

[@ATOMIK_DUNKZ]

Let’s be honest Sam, most of us don’t have the budget or resources to build a engine professionally. Most of us will build an engine just as you’re doing.

[@landcruisertoyota3980]

Poor man pays twice. Especially with engine building. There is absouletley no substitute for quality engine building , as somewhere along the line cheap workmanship will show or fail making the line especially in motorsport applications

[@ATOMIK_DUNKZ]

@@landcruisertoyota3980 I think you’re missing the point. This is for sh$ts and giggles. To have fun. If it breaks, so be it. It will be built again but, while it lasted. It was fun! Unless you’re doing this professionally, in the long run it doesn’t matter. It’s pretty obvious that Sam built his chaser for fun.

[@JACKOFALLFATES]

@@landcruisertoyota3980 maybe if you're really anxious and don't know shit about anything you're doing.... I have multiple engines all hand built & tuned. It's not hard. Just take your time and do things correctly, measure twice "cut" once. Cut being balancing, torquing, and parts used must be correct.

[@酗]

Somewhere along the line yeah, but even a amateur rebuilt Miata engine we turboed with junkyard parts has been sitting at 202whp for 12 years and 60k miles. If you just want a car to work, a rebuild is gonna leave you better off than before, as long as you don't majorly fuck something up.

[@multishit6664]

Nothing wrong with doing a good engine refresh and doing everything carefully..it will last if you keep up maintenance and use great oil and filters. If you plan on beating the engine to hell and back its not as likely to last..but if you just want to keep your classic Toyota on the road refreshing all the seals, gaskets, o-rings, and even piston rings or pistons all together..is a perfect option. You don't need to always bore and deck the block..you can buy some cheap used bore measurement tools and see if anything is really in need of machine work. 3M sells a white rubber bristle wheel with micro abrasive in it.. Its hard enough to remove old gasket but wont eat your aluminum or casting. It will leave micro scratches in aluminum so you can polish that out with a sharpening stone if it bothers you. Berrymans carb dip will also destroy carbon in a few seconds from pistons and valves etc.

[@jacobiturner]

Another Sammit Upload let’s gooooo! 🙌🏻🙌🏻🙌🏻

[@andrewbrinton1531]

Very niice! High five! 🙌

[@BOOT]

Pump that hone up n down faster, to give more angle scratches(crosshatch). If the cast iron is already flat, that sharpening stone is totally fine. Still MLS head-gaskets can be picky but composite/coated are not as. You reminded me, i need to order some 8mm LS valve stem seal install sleeves, to not cut the new seals when installing valves/springs. All i have are SBC 11/32 sleeves.

[@luke-wv9te]

just slow the drill down, go for a 45deg of the deck line. you can give it a quick blast at the start

[@DavelyDriven]

Sam, DART makes a 2JZ now with lots of differences in wall thicknesses etc.

[@AdvanceRGB]

I like every time Daiki show up in the camera ^^

[@professionalbodger]

Serious skills involved here! Awesome work Sam!

[@jetfuelg4083]

I love the channel bro but when you play the track of yourself singing I gotta mute it 😂😂😂

[@SAMMIT]

What?

[@jetfuelg4083]

@ I meant to say you have a wonderful voice and I enjoy it very much! 🤙😅

[@4EVRLOW]

​@SAMMIT don't worry I just sing along with you 😂

[@Nelsea7190]

Toms refurb has a slightly more basic "engine rebuild" process too. That polishing stone isnt a bad idea for the cost of it. nothing too fancy and it works.

[@BassManBobBassCovers]

Awesome vid format! I was thinking there wouldn't be much benefit to rebuilding the bottom end, but those ringlands were f*ed. Definitely a good call. Should be in good shape for a while!

[@icefish17]

I agree with Atomik_Dunkz, we probably will be on a tight bidget and will try to do an engine build as a project or to a car/engine we don't really care about. Love to see the Samtorials none the less.

[@wonton3063]

Sam you make it look so easy. Love this episode

[@0zWaldKuozjiee]

I swear every yr Sam has to flex something on his chaser for drift Mansuri 😂😂😂 this engine will be the cleanest missile car there

[@alexanderrivera997]

Sam that billet cover is too nice to slap that painted cover over on the jz

[@jadmjt14]

18:17 SUGOI NEEEEE~~~~ 😂😂😂 keep the outro it was so bad that it’s good now. Love it

[@salrizzo3016]

Good luck, Sam

[@DavelyDriven]

They say get help; I say get me rags and oil

[@Jonathancyganick]

S15 looks sick with chaser hood on it

[@BourneThisWay]

I had the same thing happen to my RB head bolts. The oil made it difficult for the bit to properly seat and rounded the bolt a little. I hammered the bit to the bolt and it worked.

[@jinng8694]

Gotta say, your intros are funny! 😂 Love the content. Keep on doing what you do ❤

[@Mohawk21-oi1nit]

SAM, do you not think after 5 years and possibly many before you, that it should have been time( several times) to refresh and/overhaul any and all your engines .... Experience, seat time,and just having fun will get you KNOW to the podium!!!!

[@gaveup]

Nobody: Sam: Yabai!

[@simonperry1076]

the videos are feeling good again sam!!

[@DieselEngineSean]

Koken 4020.100-M12 would have saved you a lot of trouble. 1:46

[@CFelicianoCumbas]

@sammit don’t forget to get branded sim gloves,etc. 😊

[@thereverendcoyote]

Diversification is always smart. Any career that requires talent should have a backup. Especially a dangerous careers like yours. If something would happen to you and you had to retire from driving. You can always expand the parts business.

[@ex__mortis]

someone needs to sponsor Sammit with some work benches 😂

[@turboboy0]

how about selling the springs as a kit including the valve stem seals, locks and retainers? that way shipping would be combined.

[@joewall1748]

Sammit does it ! 💪👍

[@anarchyautomotive3277]

Just for anyone watching the last thing you want to do is put a valve on a pnuematic hammer and smash it into the seat. This pounds the valve and the seat and is not providing any form of seal just ruining the the mating faces. Lapping valves should be avoided all together it is old technology which does not last anywhere the time of a properly cut seat. So it can properly work you need both the valve and seat machined which defeats the purpose of (doing it yourself).

[@95turbostang21]

Can you explain the technique that you were using with the hammering of the valves I had never seen that

[@jonathanramoslexusmaster298]

0:23 you need triple square too remove the head bolts. just an fyi

[@ashborntempest4675]

what a nice vid nonetheless and cant wait to see the chaser back up and running sam love the joke and the u know what he mean hehehe

[@Adz082]

Do u take extra dexies to stay up and do the work?

[@robb7414]

I would love to buy some valve springs for my SR20DET in my nissan pulsar gtir would they be the same as the silvia springs?

[@gmula1987]

Do those have factory head studs or do you keep incorrectly calling the head bolts studs?

[@tinyfossil]

love you bro but u killed my ears with that build music Q.Q

[@Ruftinator]

Would be funny if in a few years it wouldn't be "Sammit the KZbinr" but it'd be "Sammit the parts guy" lmao

[@lolermount4271]

Isn´t bad rebuild, its only less video friendly, but, professionally do the same on some client cars, some times without take out the engine. For the motorsports some times is better

[@lolermount4271]

Because the big clearances for very hot engines are better.

[@Twenty_Six_Hundred]

Head gasket looked fine, water jackets not so... no wonder it was overheating

[@P4FElton]

19:14 clearly a gallo 12... 😂

[@Yernaritsbarry]

You could of used the NA cresta bottom end and just got your turbo head refreshed

[@the.ghost.behind.u]

Thats a good price but a set of 2jz BC std size 80lb valvesprings and titanium retainers is only $284. Thats wut im putting in my 2jz ge vvti head on my new GTE bottom end

[@aznbrian_]

Running that with stock valves and GSC S1 cams. Runs real nice

[@BuzzNuttz001]

More karaoke please Sam 😂

[@osmond777]

lets get it in !

[@jonathanramoslexusmaster298]

2jz have the stock spring paint pointed up not down i wish i was there just too throw my knowledge with urs.

[@MrOG3Drew]

Does valve lapping increase valve lash?

[@chop_mane]

Bro coulda done some faster up and down on that first pass 🤣

[@RideSlide13]

Found the one bolt problematic bolt. More than likely lifted the head over #1 piston causing the stud to stretch and let pressure into the water jacket causing you're fountain. Just speculation and wishful thinking 😅 don't you love YT mechanics 😂. ❤❤❤❤

[@allthingsgaming9515]

I just watched an entire engine build bro in 1 video💀

[@gazvlogs7459]

Love you sammit bro but just to give you some perspective, 250$ for valve springs is like 1/4 of my monthly salary. Just for a box of springs. That is NOT cheap!

[@claudedottin1312]

Shouldn’t be building certain engines with that salary. Best to lower your sights on cheaper engines to build or be patient until you can. And you can do it!

[@Mohawk21-oi1nit]

If it can sharpen a katana or dagger, by hand , it is sharpening your " drift sword/ missile/ weapon" ...

[@Veercant]

at this point i want to see the "backup plan".😂

[@camerondonovan2140]

valve clearance- yes, maybe

[@Mohawk21-oi1nit]

Find "TAKE ON ME" BY AHA DO IT NOW! IT IS ONE OF THE TOP TEN WORLD WIDE KARAOKE SONGS (and in your key of none)

[@russellharris9579]

Bull frog out tune in z 🐂

[@Huntergaming117-YT]

W vid keep up the good work❤

[@dominicbustamante730]

How come nobody port and polish heads anymore?

[@DaltonZMS]

Biggest thing your trying to say it’s good nuff for who it’s for

[@Bull1175]

The saying is knock on wood 😂

[@JeffreyBryan187]

Yo at 29:52 you can see your timing marks are off. Might want to check that or I guess you'll notice when it doesn't start.

[@SAMMIT]

good eye, you'll see in the next upload

[@maxime_vhw]

Why does that sparkplug cover look so bad? Its soo orange pealy. idk if its the camera angle but it looks like it was rattle canned outside during a sandstorm

[@Muppetslayer153]

DONT READ THE COMMENTS!!… The Art of knowing is knowing what to ignore. - Rumi

[@xDIRTYCURTYx]

Wait Sam's leaving and Chris and Matt are in/going to Japan 😂 wtf hahaha

[@1jbaeez]

Bros preparing the car for abuse 💀

[@pwartv3528]

whys that one front cover say YAMAHA? ive never seen or noticed that b4

[@sbiccaa3584]

please please no more Samit karaoke !!

[@russellharris9579]

😂😂😂🥸

[@jadmjt14]

Don’t mess up my flow mang

[@SAMMIT]

What?

[@lou_lungz]

I 💯% agree he needs to stop 🛑

[@sbiccaa3584]

@@SAMMIT no more karaoke ! lol

[@T-Woods89]

Why does the upper timing cover say Yamaha?

[@Adz082]

He said son when you grow up ….😂

[@DULLKNOLL]

Does the plastic cover say Yamaha?? Why

[@victorwilks88]

Yamaha built the head

[@DULLKNOLL]

@victorwilks88 Interesting. Thank you!

[@v3Starz]

Sam please buy me an s14 kouki rhd please 🙏💯 im 26 from California

[@James-sir]

Do not Over Hone the cylinder it is only a couple equal passes

[@Phuquefull]

THEN BUY WHATEVER THEY HAVE LEFT. AND YOU CAN CONTROL THE MARKET

[@JeffreyBryan187]

Doesn't help you're not using the correct tool to remove the factory head bolts. Ive removed over 100 jz heads and never stripped one. But have seen people try to use Allen head sockets instead triple square and strip head bolts plenty of times.

[@sly_nz9521]

to be honest bro im all for the Rb in the chaser everyone else does the 2j in the skyline so why not the opposite who knows it might make the chaser good.... lmao jk 🤣

[@ikari_the_dreamer]

Bro sammit really want to have a rb on the chaser.

[@combatscape2000]

cool

[@thommasgriggs5056]

If you keep joking about RB swapping it. Eventually you will.

[@robsanty8454]

Why didn't you just order aftermarket pistons that are matched! 🤞it doesn't blow up

[@pxnglxy]

1JZ + 1JZ = 2JZ

[@zwierzy3383]

what is that orange luquid?

[@chadselbe59]

Damnit Sammit when you going to get a giant American V8 crate engine load it with turbos and stuff it in a nissan or something??

[@jeffreywong5112]

The black cover change color. Too stock

[@James-sir]

Go most of the way through

[@willasomavich]

Sammie stop working on the floor get your self more tables it look more professional just as you are

[@willasomavich]

Only people in third world countries work that way

[@russcoaus2043]

😄👌

[@ethantakeda]

いつも動画見ておりまーす

[@KeleabecoeDlwati]

Um not alll of us have a car at the age of 13 😅😅😅😅😅😂😂😂😂

[@manuelvictorvalderrama2533]

😂😂😂

[@hyper8545]

Hondabond is better

[@DavelyDriven]

Not sure about 1jz though

[@andrewbrinton1531]

What are you not sure about young sir? Awww shoulda gone 2j!?

[@DavelyDriven]

@@andrewbrinton1531 Whether DART will or does make a block yet lol

[@scottloersch555]

Any one who's been watching fir a while knows damm well you know thats not the full proper way of going about a rebuild brother you've done multiple srs with ockochan and we all know you know the proper ways of doing it anyone who has a dig at you fir this needs to wake up to them selves and stop being keyboard heros this whole car is a missile and gets flooged but its made for it so again whats the issue lol

[@byronwilkinson6157]

Its only proper to drop a RB in the chasers seeing as the S15 drift car has a 2j in it

[@riyadhrustam2503]

I can’t wait to order cams for my 1jz from Sam!

[@JAY-fp9zm]

Sam we all love your channel and your content but we have to be honest singing not your best quality , please stick to cars and stop putting us through the torture ....

[@relaxingperson892]

If I subscribe will you please stop singing 🎵

[@James-sir]

Are you starting to hate your subscribers you have been bitching about comments a lot lately you shouldn’t even notice them you’ve been YouTubing along time you shouldn’t be reversing

[@gmula1987]

If the bolt was already broken then why woudnt you just remove the head first then extract with the head already off? Rather than waste time struggling to weld a nut on with the head on? Am i missing something?

[@BOOT]

It was stripped

[@gmula1987]

@BOOT yes I realized that later on the video. I deleted this comment but for some reason KZbin didnt actually delete it.

[@evolad2463]

first

[@cultures843]

First

[@ShweBhoneThitOg]

i think you are not first