Rechargeable Impact Driver Restoration | Makita TD131D

Rechargeable Impact Driver Restoration Video
I bought this impact driver the same day my Hitachi impact driver, also the same price 15$. It is in good condition outside, but inside is rusty. The battery is also looking good, but inside 90% battery cell is dead. I replace new battery for testing, I will make another video about repair this battery later.
Rechargeable Impact Driver Information
Brand: Makita
Model: TD131D
Electric motor: DC magnet motor
Battery: Lithium-ion battery (Capacity 3.0Ah)
Voltage: DC 14.4V
Rotation speed 0 to 2,400min-1 (rotation / min)
Number of hits 0 to 3,200min-1 (times / minute)
Tightening torque Up to 145 N · m (1480 kgf · cm)
M14 (Strength classification: 10.9) High strength bolt tightened for 3 seconds
Tightening ability
Machine screw: M4 to M8
Normal bolt: M5 to M14
High strength bolt: M5 to M12
Course thread: 22 to 125mm
Machine dimensions Length 145mm x Width 79mm x Height 235mm
Weight 1.4kg
I hope you find something useful & enjoy this video!
I am happy to receive your feedback, advice, suggestions to improve myself.
!!! I apologize for the mistake if I have made in this restoration !!!
--------------Thank you so much for Likes & Comments--------------

[@cgomeznoe]

Upgraded from an older 18v kit. kzbin.infoUgkxW1vOBRCMrgTCDEijzpVzDWsgI-Jm2iQv I independently chose the drill and impact tool, before I came across the kit.I like the 3 speed impact gun. It seems more powerful than my older one, and it can be set to be really gentle. The drill is more appropriately sized for my use. I used to have a hammer drill, but I did not like that it was so big and it was not a great hammer drill. I rather have a smaller drill like this, and then get a corded hammer drill for the odd case I need that.

[@milikan29]

No stupid music, no chit-chat. Just a clever guy working efficiently and machinery sounds. This is therapeutic. Keep up with the good job!

[@Aldo2m0r04]

If You want to repair that battery pack, replace ALL the cells with high drain cells (with 20/30 A), don't use the cells from laptop batteries, they have 3/5 A (too little). Greetings from Italy!

[@Aldo2m0r04]

Ah yes, last thing, if the circuit is too rusty and doesn't work, You can buy a replacement circuit for little money.

[@gear_show]

@MUR3O2OO4 Okay, I am hard to find high drain cells here, I just found ICR 18650 cell 1700 mAh 3.7V. Anyway thank you!

[@artbyrobot1]

@@gear_show liionwholesale.com/

[@seancervantes1]

Look at vaping batteries. They use 18650 20/30amp. Imrbatteries.com sells good cheap ones

[@RoadRunnerMeep]

There's something so relaxing about watching restoration videos from what they start to finish and fixing things rather than throwing them away

[@ibrahimalmasri3745]

مش

[@taytase]

I really appreciate your attention to detail! Every spring, every surface of connecting parts, every screw, was made to look and perform like new. And it shows. Thank you.

[@gear_show]

You're welcome, thank you for sharing!

[@codustv1465]

@@gear_show Do keep all of these or sell some? if you keep them you should make a video showing all restored tools!

[@GraduatedIn]

Idk why everyone is commenting bad shit about this, it’s a great restoration and it’s just a tool god damn it. If it breaks he’ll fix it again or buy a new one. It’s not that hard. It’s not like a part from NASA.

[@tunaonwhitenocrusts]

I saw the red impact driver and thought.... hmmm... a broken Milwaukee? Then I read "Makita" and thought it was a typo. Then he opend the case and I saw the blue charger. So confused.... haha

[@TomD0131]

Same here!

[@ardsjd6869]

saaammeeeee

[@finnbarber1488]

Same

[@pokyoo7974]

@@TomD0131 zzzzvzzvzzZvzzv"€xv¢xxz C€Cc v cc €V Vz€V xZxvzv¥Z"zzzCzz€zzz C¢z£€$z zzz v xxz xx vz£$V Cc zzz Cc hxxxZxHXHXHZxxzhzxxh

[@pokyoo7974]

@@TomD0131 A

[@loeffel_hh]

*Gear Show's wife* Why did you bring another impact driver, you already have one. *Gear Show* The point different is sound. This Hitachi impact driver is quieter... :D Great

[@billn6534]

You are an absolute artist. You use the finest tools and you recreate beautiful parts on your milling machine.You are willing to go the extra little bit to take a 90 % restored item to it's perfect 100% and more. TySy Tube is an example of someone with a little skill but not much pride. He has copied your Channel in so many ways but he uses cheap substitutions. He does not use a milling machine to polish. Instead he uses a power drill. What you do when you restore paintable items is an example. The watch makes measuring tool that you restored, you filled in the rough metal blemishes before you primed and painted the base. The black finish was beautiful. TySy paints the metal in it's rough form. The details are important and if you look for his restoration of a "GIGANTIC Lighter "you will see what I mean. Also he restored a vintage coffee grinder which I believe you would have made it appear more beautiful than he ever could have. I notice that TySy sent you an item to restore and you made it look beautiful!! I think it was too hard for him and he sent it to you to try to have you fail at its restoration. That's enough of me going on and on. I appreciate your skill and artistry. May you and your loved ones be safe in these Covid-19 times.

[@colinmcmillan2642]

Thank you for sharing your amazing skills with us. I always look forward to watching you work. Greetings from Scotland. 👍

[@gear_show]

You're welcome, I am glad that my video popup in Scotland. Thank you!

[@retronnaldestersonterson]

I always waiting for your new video All your video that post on youtube is awesome I give you one like to you Good job. Doesn't work anymore matter. Your restoration any kind machine. You always make it work. This Comments For You !!!

[@gear_show]

Your comment makes me happy with my work. Thank you!

[@retronnaldestersonterson]

@@gear_show Welcome , Get rid My stress

[@retronnaldestersonterson]

@@gear_show what is your next video you going to do

[@boastyy]

Awesome video! I can safely say if I stripped the impact driver down as much as that it would never work again, ha. Nice one for getting it back working better than it was before.

[@markharris5771]

At last! Someone else who leaves that funny foam stuff in their better better tools and equipment! My wife is convinced I’m the only person in the entire world that does it. I can now let her know there are two people in the entire world that do it. Another great restoration, you’re going from strength to strength and it’s always a joy to see you expand your arsenal of tools. You are without doubt one of the channels that really deserves your success. Your videos have a wonderful ASMR quality. Thank you.

[@rodw]

Very nicely done !!! Kuddos to you for having the talent to do these types of restorations. I didn't see one part dropped? Great dexterity. Thanks for sharing your talent and videos, Rodney

[@bufoncosmico]

Great video without unnecessary editing and horrible generic background music. Amazing restoration as always!

[@user-rw3nr4rv3c]

Круто .Это сколько терпения нужно чтобы все детали на место собрать .Обалденное видео .

[@gordbaker896]

I did not see the 2 balls being installed in the chuck, however, You obviously put them in. Good Job, Good Tool.

[@BlahBlahManYeah]

Gord Baker 12:26

[@gordbaker896]

@@BlahBlahManYeah I meant the 2 balls in the Bit chuck that holds the tool. 14:18

[@agunggunawan899]

Me neither.

[@kungfusing1]

ive seen a lot of pros using the makita impact driver - looks like a beast nice work!

[@jj325j2]

I'd buy that hitachi from you. Sounds like the jetsons, my kids would love to help me out more with how quiet it is!

[@Tom-mv1hk]

野村さんもこんな綺麗に直されてるとは思うまい…ww

[@vicv9503]

i think it's a bit more noisier due to certain points in the gearbox lacking any grease. but hey i should mind own business lol. good job man.

[@user-qw7sb7ou4p]

I'm looking forward to the next video...!

[@Abo_Zead]

You are always creative from Saudi Arabia🇸🇦👍🏻

[@claya6581]

Touching those batteries like a fearless madman. Those things are dangerous friend; be careful.

[@gear_show]

Oh, thank you so much.

[@cg6522]

Nice job ! Looking forward to your next battery vid.

[@miroslavpejchal2720]

Good work, good tools and super video. 👍 I'll look forward to next one.

[@gear_show]

Thank you :D

[@12345axes]

Love this channel, subbed! Nice brooo

[@humbletrack5448]

Thank you! Helped me open my old driver and repair!!!!

[@desarsahreza]

Q1qq1

[@robertdimas9046]

I've been waiting for this vid since I seen you use it on other restoration s thanks

[@RingZero]

Very inspirational restoration, keep up the good work

[@chazzcombs]

Your videos always amaze me. I have no clue how you figure out how to a: take stuff apart and b: get it back together. You're like a wizard. Keep up the great work!

[@thegoodguy44]

It’s pretty easy.

[@willysir8836]

Very Good Job done ! Just few points : Don't forget to clean inside the parts such as springs Don't be stingy with grease : i would put some on electronic part to prevent from rust or oxydization and i would use lithium gease for moving parts a tip : you can use baking soda to clean very well

[@kaseryn]

You need an awful lot of time, patience and tools most of which i don't but it is fantastic to see it done!

[@plunder1956]

It actually looks well built - Neglected and very dirty, but it works well after the rebuild.

[@manoelsilvasantana6243]

É muita pecinha amigo 👏👏👏 você é um profissional mesmo 🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷

[@JorgeLuis-sm5cm]

Uma vez abri uma em casa quase não consigo montar mais

[@stevenhoman2253]

Nice job, a pleasure to see.

[@prairiefarmer5994]

So this is what AvE would be like if old uncle bumblefuck restored tools instead of destroying them.

[@dainius4168]

+1 for bumblefuck

[@rzerizrz]

@@dainius4168 -3 for farmer xD

[@andrewjarvis5814]

Instead of sitting on the healing bench he sends them off to this guy.

[@GT-C]

Good, I like you change a new battery for test!

[@user-gt1nd7bb2w]

Очень познавательно, образовательно, very informative, educations!

[@Inkviz05]

и очень тупо

[@Dereazar]

Это не ремонт, это чистка без замены деталей и нормальной смазки.

[@inzynierumysu138]

U got amazing tool's

[@rcmaquinasferramentas247]

Bom de mais seus vídeos, parabéns pelo seu trabalho.

[@briankruse3584]

Just curious, what do you do with all the drills and machines after you restore them?

[@lisov4575]

Where does a man learn such incredible knowledge of electrical and electronics?

[@gear_show]

I learn them from KZbin :)

[@ermersonmorais5707]

hello here is from Brazil, I love to watch your videos, I'm facinated with the restorations you do, congratulations on the channel

[@gear_show]

Thank you! I am glad that this video popup in Brazil again.

[@savneetsinghrairai6823]

Well such a little motor such a great torque may be due to strong neodium outer core impressive as I believe that only pnumatic drivers have enough tourque

[@inferno66750]

Hello, Nice video as always Why you don't use electrolytic bath in order to remove rust? I think it could help you a lot ;)

[@diegoantunez505]

Excelent video man!!!

[@user-dx6pt9oo6h]

Hi Gear Show 👋👋👋 very very good restoration Electric Dril 👍👍👍

[@00andrei18]

Use some grease to keep the o-ring in place. at 14:05 .

[@masterat9113]

everything will be much more easily when you use the right tools

[@robocop6666666]

You sir are a very clever man🇬🇧

[@gear_show]

Thank you sir!

[@frontstreet2011]

Can you please give info on that red long tool box with sockets & etc that you used to open drill. Make & model would be perfect please. Thanks and keep up great work. Love your videos!

[@user-wq5zt3px6l]

KING TONY

[@robertgilmour1903]

Excellent rebuild.

[@kennethgilbertdds7249]

If people used their toothbrushes this well on their actual teeth, no one would have a cavity. Ever. Very good work

[@QuintinGellar]

Yeah that thing would be in the bin if it was me. Because I wouldn't have any idea how to Reassemble it 😂😂😂

[@user-wr2os9nx9n]

Видео топ побольше бы таких видео)))))

[@dosetti]

The gasket dropped at 14:05 and now its misaligned inside..

[@hamidrezasadeghi9267]

great video again tank maybe u must restore box too

[@gear_show]

Thank you for the suggestion! At the beginning I think I should restore box too, but It make this video so long. I want this video to be short.

[@trong6124]

Amazing!

[@neilhannah8356]

Another great video! Thanks!

[@chinachodsukitorankun1864]

Where are you man

[@paulotorrobia7030]

Muito bom so os melhores faz esse tipo de serviço

[@sabo9932]

Finally you uploaded a video 😌😌

[@retronnaldestersonterson]

wow you have so many new tool

[@nybpx96]

Can you help me? witch part is respond for the impact?

[@gchavsg1905]

Nice restorations , good videos , greetings from Central America 👋

[@gear_show]

Thank you! I am glad that this video popup in Central America.

[@gchavsg1905]

@@gear_show yes , you're great!! Like 👍

[@moldac32]

Parabéns, nota 10

[@MultiSupertux]

Nice work🙌🙌🙌. And you need to tighten the vise well. Sorry for my bad english😆

[@claudecharland5091]

amazing work of restoration great job

[@hannasuyin7610]

this video hipnotized me

[@jerryhe2152]

你太厉害了👍

[@aidanboyce258]

Hey was just wondering if you could do a tutorial on removing and putting back together the anvil on a makita dtd 171 I have a snapped bit stuck in there and it would help a lot thanks

[@keanuheunisch7383]

Great to see another video from you Where do you get these tools to restore? Greetings from Germany

[@gear_show]

I get those tools from second hand shop in my city (Phnom Penh). I am glad that my video popup in Germany. Thank you!

[@thecynic807]

Great now in going to have dreams about that awsome socket set you have.

[@gear_show]

I have been wanting it for a long time. I just bought it this project.

[@thecynic807]

@@gear_show i cant afford it right now or id be buying them. You should create a link for the tools you have. Make a buck off of Amazon

[@user-hd5mw3vv9v]

日本の何かしらの職人ノムラさんが現場で使い込んだインパクトが外国でまさか綺麗にリペアされるとは思ってもないだろうなw

[@tanis143]

In regards to the battery pack, do NOT use that one cell!! Each LiON battery is good for only so many charge cycles. You stick that old one in with all new ones and the battery pack will fail soon! Its actually cheaper just to buy a new battery pack than to replace the individual cells. A new replacement batt (off brand as Makita doesn't make these batteries anymore) will run you about $50+ shipping. Eight 3.7v 18650's (judging by the wrapper those are Sony VTC3-4) will run you about $72 bucks ($9 x 8). Just buy a replacement battery and stay safe!

[@micjubba709]

Nice job love makita

[@mrcokez1]

this was extremely satisfying

[@jacobreyna6069]

Only question is where do you get these drills and impact drivers?

[@gaizkazalduendo378]

Great video like always! Where did you buy that 14.4 v battery? Thanks!!

[@gear_show]

There are business man import second hand things from Japan to my city (Phnom Penh). I away go to his shop looking for power tools.

[@jeffreybowd1249]

Love the colour, wish I could have one

[@yeagerxp]

Very good restoration 👍👍👍

[@user-pp9ti9nr7v]

野村さん、ちゃんとメンテしない人なんだなw

[@diyeverything2177]

👍👍👍I like this project,👍👍👍

[@Ihaveaboyfriend]

Nicely done 👌 Subscribed

[@jmyyer]

Like the big wrench, which reference is it ?

[@patriotofpak689]

Makita is really fantastic tool...

[@warrenbaker9049]

Do you have a link to the socket set you used at 3:20?

[@MGTVDeutschland]

Good work. Greetings from Germany ♥♥♥

[@gear_show]

Thank you! I am glad that this video popup in Germany.

[@ot9180]

Very good, thanks.

[@zoisbasis7791]

A cousin gave me a Makita impact driver, TD121. The problem is no battery, no charger so I can't give it a try to see if it works. Any idea??? Love your videos, refreshing, inspiring and relaxing. Thanks a lot!!!

[@robertobezerra8376]

Fantástico trabalho maravilhoso tmj.

[@guilhermereis1155]

Eu gosto muito de assistir os vídeos desse canal

[@orlatris96]

FANTÁSTICO, ADOREI

[@gear_show]

THANKS!

[@tomalcolm]

Mr Nomura: where’s my drill?

[@Tom-mv1hk]

同じこと思いました（笑）

[@sta-prest]

ワロタw

[@allenang9541]

I wish you could repair my lug nuts impact wrench. It will be a good video for you and I can have a working wrench. It's a win win.

[@gear_show]

Yes, but the cost for delivery maybe expensive...

[@carboumen7661]

Buen trabajo 👍

[@sluge1]

Did your replace the rubber rings or used original ones?

[@jairodiazcifuentes160]

May You tell me what is the type of grease you used, please?

[@mpalaskokkalis1476]

Perfect

[@valdirsilva8542]

o amigo onde vc consegue todas essas ferramentas que vc restaura?

[@conqwiztadore2213]

do you think using heatgun on the plastic frame of the drill will restore the gloss and help blend the scratches?

[@strangetar2833]

No because most expensive power tools are made of polie glass fiber