Reese Goosebox 20k Added Built In Compressor Review.. No more Chucking!

[@jeffjohnson2313]

It would be great if you could add the list of material you used- fittings, switch , pump etc. thanks!

[@MWR-lg9qp]

Just installed the Gen III Goose Box on our 40 foot Fuzion toy hauler, man what a smooth ride. I just added a 90 degree air fitting to mine, but I like your design much better. Great job.

[@RockyRohde]

Thanks for watching.. I’m definitely never going back to a fifth wheel. Once you pull with a goosebox nothing compares..

[@switz11]

Someone else asked but...Could you please list all the parts for this conversion? And provide links? Thanks and a great idea.

[@DavidBrown-jt7yi]

This is really good info. Very nice work to get that built in for convenience.

[@GeoffYarber-f5u]

Any chance you got link to the fittings you used? Ones I bought will not seal at the threads. Tried dope, teflon without luck.

[@briantillett2305]

That’s slicker than frog snot. Nice work!

[@RockyRohde]

Thanks 👍

[@Jason-tz8xn]

Rock n Roll, this is awesome. I'd love to see a quick video of how the Viair is set up in the battery compartment. I assume you still have the ability to use your compressor for filling tires?

[@RockyRohde]

I have a separate one on the truck. I just added the pump and switch..

[@JLTPhotog]

1500-2200 pin weight on a 45’ toy hauler? Is that right? I have a 37’ Reflection (14kgvwr) and the pin weight is 3100.

[@MichaelHarrison-y2v]

would like the fitting need as unable to get them off the you tube clip and unable to make out please

[@GeRom831]

Thanks for the video. Is that Big Foot in the background?? 😮

[@RockyRohde]

Texas toy Diesel monster truck from the 80’s.

[@RockyRohde]

Go to my channel or search Texas Toy on you tube. Lots of videos of the complete restore.

[@stevenlucas304]

I'm looking at the Goosebox and Gen-Y offset as well and wondered since it rests on the bed, is it wearing the spray-on liner or the bed itself? Nice idea with the remote air.

[@RockyRohde]

I have not removed it yet to check

[@stevenlucas304]

@@RockyRohde Curious to find out, I was thinking about putting something nylon like a lube plate between the base and bed. Is there a relief valve in the brass piece you removed? Meaning there is no relief valve with the direct connection.

[@olsonatrs]

How did you run the air hose?

[@RockyRohde]

Drilled up under master bed and ran under bed.. Then drilled back down to front compartment. I have about a 3-5ft section under the bed. Then siliconed and sealed

[@zackheenehomes3946]

What compressor and switch did you use? Thx.

[@RockyRohde]

Firestone wr1-760 2229 Viair 12 volt

[@user-km3ln6lw7o]

Did you have to drill hole in back of hitch for your air line ?

[@RockyRohde]

No… I ran it through the top

[@DaleStagg]

Just wondering why the elaborate setup with compressor? Once you add pressure would it not need further adjustment? I added air to mine and seems to hold well without adjustment.

[@RockyRohde]

Depends on what I’m hauling in Toy hauler.. pin weight is almost half when my canam is loaded vs unloaded.. it requires different pressures.. on a fixed RV I agree…

[@DaleStagg]

@@RockyRohde thanks, wondering if I was missing something. I see now with your situation, that is awesome.

[@MichaelHarrison-y2v]

can you please list the fittings

[@RockyRohde]

This is what i used for the hitch.. the rest you need is all 1/4” tubing line to fit your design.. Stainless Steel Adapter 1/4" NPT... www.amazon.com/dp/B01LQU8HPM?ref=ppx_pop_mob_ap_share

[@MichaelHarrison-y2v]

thank you

[@MichaelHarrison-y2v]

please list the parts needed

[@RockyRohde]

1/4” tubing Viair compressor Fittings Air lift panel with gauge and relay

[@rogergraves242]

Put that Valve underneath the Hitch.

[@trumpwon8231]

The air fitting for being a gen 3 on the 20K, is so under engineered. Clear the person does not RV. Just terrible for so many reasons. Folks they got paid to make Our life misserable.

[@issyauto_kyra2225]

Hello there, this is Kyra from ISSYAUTO, a professional brand dedicated to producing the best car parts. We would like to invite you to try out some of our products for your Ram 2500. Would you have interest in working together? Look forward to hearing from you. Thanks!