Refilling a hydraulic jack or cylinder is pretty straightforward if you’ve got the right tool. I modified a funnel with a piece of silicone tubing. It took about 10 minutes but everything worked just fine after we were done.
Пікірлер: 33
@billjones51782 жыл бұрын
I tried this way, worked on my 18” hydraulic engine lift. Thanks
@edwardmcgee5465 Жыл бұрын
really good video thanks!!
@antonios49263 жыл бұрын
Thanks for the video. I have a Genie scissor lift. What type of hydronic fluid do I use? I am getting conflicting advice.
@kevinroughton36702 жыл бұрын
I had not used my hoist for a while and it decided not to go up any distance. I figured that as I pumped the jack a vacuum was being formed inside the reservoir because of the rubber bung. I removed the bung and no problem - I think there should be a breather on the reservoir instead of the bung.
@fishingwithsam752611 ай бұрын
Thank you brother
@frankgalassi78214 жыл бұрын
Can you fill it while the jack is all the way extended out?
@WiseRuler2 жыл бұрын
So I've added oil to mine but it still won't lift a load. It pumps and lifts without boom attached but not with. I've tried bleeding air but maybe I did it wrong or it could be bad seals inside? I got it without oil plug in it. Maybe debris or junk got in it?
@Dev_Everything4 жыл бұрын
how do you purge the air out of one? I heard that you must turn the valve to the OPEN position and then pump the jack a bunch of times and this will clear the air
@dgaz3057 Жыл бұрын
yes, then you are supposed to leave the lower valve open and then release pressure out of the rubber plug on top, insert a small screwdriver on one side of the upper rubber plug, and pry it enough to allow air to escape without removing it. Close the bottom valve and then pump away.
@mule66629 күн бұрын
Everybody thinks they know it all😂 so no bleeding air out ?
@dannilaser165 жыл бұрын
Do you have to have the lowering valve open when you fill the oil, or in the closed position?
@livefree68785 жыл бұрын
As I recall the valve can be open or closed during filling.
@seshachary55804 жыл бұрын
nice thank you
@spencerdasilva2 ай бұрын
Thank you
@dgaz3057 Жыл бұрын
bleed process?
@hipairbrush10533 жыл бұрын
Would it harm anything to rub this oil on the post to keep it from rusting?
@tortron Жыл бұрын
I do this for one kept outside. The only issue can be if dirt sticks to it, it will. Shorten the life of the seal. I just wipe it down before use
@karol84712 ай бұрын
Można też dużą strzykawką taką ze 100ml
@user-bq3hc3jg2y Жыл бұрын
can anyone answer this ( if i was to weld shut the fill hole on a long ram jack like the one in this video would it effect its functionality? )
@dgaz3057 Жыл бұрын
yes thats how you bleed it. If you lost the rubber plug, I would tap it and find a small bolt to plug it.
@user-vw4jd6eo8p6 ай бұрын
👍👍
@Richard-kz2om11 ай бұрын
What is the position of jack???
@BOOSTJUNKY3 ай бұрын
Down
@patelpower35792 жыл бұрын
Oil grade ???
@billjones51782 жыл бұрын
Too about a pint of hydraulic oil.
@dansteving5915 Жыл бұрын
or use an oil can and done in 15 seconds.
@peauafi3 жыл бұрын
Heard of nail clippers lol
@haroldborders37493 жыл бұрын
Nail clippers don't open that wide.
@philjones86922 жыл бұрын
Seen how far his thumb bends the wrong way
@user-ph1jp5pz8e Жыл бұрын
Them finger nails 😂😂
@bmwe30club646 ай бұрын
Your mother
@Emoriatwc4 жыл бұрын
I cant trust a guy that wears a ring in a workshop