Thank you so much. I am not sure why I have to do this on a new hoist though. The video was what I needed.
@PoormanscarGarage2 жыл бұрын
Glad it helped
@Ngcarson1337 Жыл бұрын
Thanks, this helped me sort out a finicky secondhand engine hoist.
@PoormanscarGarage Жыл бұрын
Glad it helped!
@sylviac1846 Жыл бұрын
Thanks I inherited one and I use it to help with my kayak loading.... had no idea how to fix it! Now I do!
@PoormanscarGarage Жыл бұрын
Glad I could help!
@o6i6i68 ай бұрын
Bro, you are a genius!
@paintballalienindy092 жыл бұрын
Thank you I gotta get this co-rolla out of my garage
@Joeylucio223 ай бұрын
Thank you , you got another sub 😁
@cravinbob Жыл бұрын
Use only hydraulic jack oil. Other fluids can wreck o rings and some do not have thickness to seal and lift. I raise it the arm to fill it then pump a few times then lower it after putting in the plug. Do not remove plug when arm is down or get a face full of jack oil.
@joezoodie78654 ай бұрын
Thank you, 30 seconds of reading saved me from watching a video that was wrong. You don't fill it when it's all the way down you fill it when it's all the way up.
@fernandeze46192 жыл бұрын
thanks bady exellent vidio
@PoormanscarGarage2 жыл бұрын
You welcome
@johndempsey86432 жыл бұрын
Nice! Thank you!!
@PoormanscarGarage2 жыл бұрын
You bet!
@notmyname7312 жыл бұрын
Got mine today and pulled the motor it worked fine but went up really slow
@CarModsGarage2 жыл бұрын
I did that on mine and it changed for the better a lot
@nickmurphy39358 ай бұрын
How do you know when all air is out/when to stop pumping ?
@chrystianrico34666 ай бұрын
Do you know how much oil it takes when you do the purge/refill?
@valterbeicinha96336 ай бұрын
I bought mine and discovered it doesnt go upwards all the way, is it fixable?
@AR-mb3id9 ай бұрын
When I do the pump step oil gushes out if the fill hole. What am I doing wrong?
@JoeWood73 Жыл бұрын
Thanks!
@SnoopyCars Жыл бұрын
I got a Duralast engine hoist that’s leak a little bit but I’m not sure what to put fluid it. What did you use or what should I use to put in the cherry picker?
@PoormanscarGarage Жыл бұрын
I switched to engine oil, but by factory manual you should hydraulic jack oil
@FranksShitBoxCollection Жыл бұрын
So while the cylinder is resting I remove the bleeder, drain it, put it back and fill it until the hydraulic fluid is leaking out? Reminds me of doing a rear differential
@PoormanscarGarage Жыл бұрын
yeah
@romano543212 ай бұрын
Do these pumps leak normally? I just bought a used Pittsburgh lift and it lifts but it leaks at all the bottom seals. Should I look into replacing the seals?
@PoormanscarGarage2 ай бұрын
its always like that, they all leak
@AR-mb3id Жыл бұрын
How do u know when to stop bleeding?
@notmyname7312 жыл бұрын
Do you open the release valve all the way or just loosen it
@PoormanscarGarage2 жыл бұрын
just loosen it
@nsbtacoma6650 Жыл бұрын
Mine will lift no problem but will slowly lower to the ground after half hour or so. Very slowly loses pressure. Feel like I’ve tried everything
@PoormanscarGarage Жыл бұрын
I think its bad seals in your jack bud, same is here
@AraceaeFanatics Жыл бұрын
It's that loose pressure.
@bitchut32182 жыл бұрын
Shouldn't this be done with the long ram being fully extended?
@jamespage6168 Жыл бұрын
No then it will spray out fluid when let down
@slambert1235678 Жыл бұрын
@@jamespage6168 I found this out the hard way
@huntergardner597 Жыл бұрын
@@slambert1235678 😂😂😂
@Simplemind45Ай бұрын
Do you know if rubber grommets are sold separately?
@PoormanscarGarageАй бұрын
I'm sure you can find it online
@BargainBandit2 жыл бұрын
can you link to the 3d printed file for the knob you made??
@PoormanscarGarage2 жыл бұрын
Yes once I find it bud
@joeyrao402 Жыл бұрын
@@PoormanscarGarage did you ever find it?
@brianwilkins975011 ай бұрын
There are at least two on thingiverse. I searched engine hoist.
@putrol4.22 жыл бұрын
I did all that but it still won't lift all the way up any ideas
@PoormanscarGarage2 жыл бұрын
Not sure bud, might be that your cylnder is not good, and what do u mean all the way up? try doing it under load.
@putrol4.22 жыл бұрын
@@PoormanscarGarage it will lift engine up half way easy then next pump it will go up an inch but drops back an inch & holds weight but won't go higher
@PoormanscarGarage2 жыл бұрын
@@putrol4.2 u might need more fluid or could be that ur cylnder is leaking