⚠️ *Found this video super useful?* Buy Paul a coffee to say thanks: ☕ PayPal: www.paypal.me/TheEngineerinMindset
@jcortega86755 жыл бұрын
This is an underrated channel.
@franciscoprieto68014 жыл бұрын
I really like this channel. It's better than the university
@esnutrisari17783 жыл бұрын
very usefull for design, monitoring, and analysis.. it helpful for my job
@EliteHydronics.4 жыл бұрын
Brilliant channel ! 👍🏻 thanks
@kmutech7186 жыл бұрын
sir your videos are too good can you please upload plumbing calculation design such as savage and public health plumbing for high rise building
@matthewzook18594 жыл бұрын
Thanks for the video! Very informative! I'm looking to make a dehumidifier for a lumber drying kiln. How would a traditional heat pump type system be altered to make it most effective as a dehumidifier? How cold should the evaporator get? The kiln will reach 140 degrees and I'm planning to have all of the dehumidification components inside (so the heat from operating it can heat the kiln). Any insight would be greatly appreciated. Thanks!
@abdullahosaf14762 жыл бұрын
Hello, and thank you for the wonderful content can this software be used to design a hydronic system with 3 branches, each having two coils in them? Waiting for your kind response.
@shreyaskumbhar70474 жыл бұрын
Very informative
@estherkyere6937 Жыл бұрын
Thanks for the video
@EngineeringMindset6 жыл бұрын
Video was re-uploaded because it was accidentally deleted
@OthmanAlikhan2 жыл бұрын
Thanks for the video =)
@kaf2303 Жыл бұрын
Excellent!
@robertingersoll52894 жыл бұрын
The ASHRAE PH chart Enthalpy is different from Danfoss PH chart Enthalpy values. Do they use different datums?
@akashpathak58954 жыл бұрын
Will components be compatible if not purchased from Danfoss? Suppose if we use this software for components selection(compressor, evaporator, condensor, etc) will it be compatible with other companies products
@कोंकणकर4 жыл бұрын
Sir please help me. How to select condenser inlet and outlet temp. And pressure for refregeration system. Which book refere to me?
@talhaozden40413 жыл бұрын
a very good work, How can I find enthalpy values at different temperatures and pressures (for R410 fluid)? I need to have the T-S diagram drawn.
@EngineeringMindset3 жыл бұрын
theengineeringmindset.com/refrigerant-properties/
@solankipratik80714 жыл бұрын
Can we design brine type block ice machine based on freon 404a?
@MihaiP124 жыл бұрын
How are the properties calculated at point 3 when considering a degree of subcooling, thus the point not being on the saturation line? I would like to know what tables or formulas to use to obtain enthalpy and entropy at that point located in the zone of subcooled liquid refrigerant. Thank you in advance.
@EngineeringMindset4 жыл бұрын
Check our design videos
@ahmedmahmoud45664 жыл бұрын
Dear sir Thank's Pleas l wante know How many meters The Evaporater and Condenser in the industrial chiller stc ice maker how can l calculati il? pleas
@udithaatukorala65786 жыл бұрын
dear sir ,your videos are v.good .i wont to design -35 c freezing bath for pop ice (popsicle ).please help me.thank you
@EngineeringMindset6 жыл бұрын
Check out kzbin.info/www/bejne/ioHEk6lvnql4hMU
@nsalam9 ай бұрын
Is the a app version of this software?
@kimgalinato36342 жыл бұрын
This also applicable at AC Design?
@EngineeringMindset2 жыл бұрын
Yes
@JJ-mg3pr4 жыл бұрын
We need training for cold room in Bangalore India.