Removing universal joint using Lisle 42890 small U-joint puller. The other puller shown in this video is Lisle 42900 medium puller.
Пікірлер: 23
@CT9905. Жыл бұрын
I have the same Tiger tool and Milwaukee impact, good video.
@terrellscaife24112 жыл бұрын
Good video these will not work on some of the GM driveshaft because it’s too much of a slant but when you do get a chance to use one of these over a ball joint press it’s much more efficient I think I have like 23 U joint puller resize a restyle
@raincitywrench1172 жыл бұрын
Good to know. Wonder if a piece of shim stock can be wedged in the outer end of yoke to get it straight?
@terrellscaife24112 жыл бұрын
Nope it’s just the way those older GM driveshaft for me well at least the aluminum ones I did a 1994 GMC 1500 van and I ended up using a ball joint press to pop out do U join I think they’re steel you joints might be different but I don’t remember
@terrellscaife24112 жыл бұрын
OK I just remembered I used the u joint puller tool to do the Front u joint on the propeller shaft for a 2003 Chevy trailblazer so on the trailblazer you could use the special puller tool
@Bill-ts9zv2 жыл бұрын
Simple tool but effective
@loukoponosh13722 жыл бұрын
That actually looks a lot faster then a c clamp press.I might pick this tool up the can be a bear to get out and that’s with a good clamp did you use to install if so how did that go ?
@raincitywrench1172 жыл бұрын
This will definitely be my go to when removing u-joints from now on. No it's not an installer but installing is the easy part. I used a hammer to taps the cups in on this particular job. Placing in vise or c-clamp works great also.
@ChrisNieves Жыл бұрын
Wish mine came out that easy. I have the same press but no success it was just twisting the shaft joint. Ended up using a ball joint press to get them out.
@raincitywrench117 Жыл бұрын
I think using the torch was the trick on these or else they may have not come out.
@oby-16079 ай бұрын
@@raincitywrench117 So many people forget to use a little heat and end up bending the ears.
@raincitywrench1179 ай бұрын
I made that mistake years back 😪@@oby-1607
@troydietrich52332 жыл бұрын
2007 Cummins 4-4 Front drive Shaft what size do I buy.
@raincitywrench1172 жыл бұрын
Pretty sure you need the lisle 42900 medium one. I think the large will be too big. Check the Q&A on amazon and I bet it will say
@DG-vids4 ай бұрын
The 890 Won't fit on a chevy 2500 truck driveshaft with aluminum yokes.
@raincitywrench1173 ай бұрын
Oh yea, good catch. Those have the thick yoke aluminum driveshafts. Have to use a u-joint or ball joint press.
@dangerdavefreestyle2 жыл бұрын
the ears on the yokes and driveshaft are flat and have an angle to them while the tips of that tool have curves. great for pushing on a ujoint but not yoke or shaft ears, thats the only problem i see with that tool, and the width is not adjustable. better than beating it with a sledge though by far.
@raincitywrench1172 жыл бұрын
Yea. The couple times I used, it worked pretty good.
@chekelley68612 жыл бұрын
I have a set of these and I’m mostly disappointed with them
@raincitywrench1172 жыл бұрын
Why is that?
@nitrous07me4 ай бұрын
I could’ve used this today, F I’m pissed😅
@raincitywrench1174 ай бұрын
Had a real stubborn u-joint one day so decided to pick up the tool & said never again 😎