Renault Key Card programming with Renault CAN CLIP

This video is about Key Card encoding/programming

[@woollywhippet9899]

I used this method to do my Clio mk3 with standard key/transponder and it works great. Programmed a spare key for £10 off EBay from China. Excellent video may do one to show how I did it. Many thanks for posting !!!!

[@MP-tf5sd]

Did you follow the video exactly even though it was a standard key rather than a card?

[@elliotthale1835]

did you end up doing a video?

[@franziskaxxx6059]

Hello, my dear, First of all, great videos from you. Now my question. I have 2 original Keyless Go cards from a Renault Espace 4 built in 2007 a card the case was broken and I opened it and then I lost the original pill, so I got a replacement pill and a new case. Now I've got the card where the pill was gone so far that I can drive with both cards, but my Keyless Go doesn't work. According to the Can Clip, 2 cards are read, but the Keyless Go says 0 How can I add the cards to Keyless Go? I have Renolink, DDT4All, Renault Can Clip from 159 - 237 in my online shop, but I would like to lock my vehicle again, the strange thing is that when I go shopping and come back the car is locked and I only have to go to the driver's side Reach into the door handle and pull briefly and all the doors open, but not every time. I also have a Renault pin calculator. -------------------------------------------------------------------------------------------------------------------------------------- The order of work at Renolink is: 1. Press “Read Pin” 2. Press “Connect”. 3. Insert a blank card 4. Press “Test Presence”. You will see the card code and see if it is clean 5. Press “Start Learning”. 6. Press the learn button/card. The message is displayed: Map learned Ok! 7. Insert the old card 8. Press the Learn Button/Card to open the pop-up window and display the message “Card Learned Ok!” Both cards are displayed in the window 9. Remove the card, check the checkboxes of both cards in the program and click “Validate” (no information is displayed). 10. Press Disconnect. If you do not select “Test Presence” before inserting a new card, you will receive a “Card not learned” message. Best regards Kalle

[@kostelectronics]

Thank you very much!!! with your help, i was able to help a friend and programming his new keycards!!

[@BeatsByMe290]

Which year?

[@berndm.5595]

Megane 2 CC `05. Habe jetzt unendlich probiert. Nach dem Einlesen der Schlüssel kommt immer die Meldung "Ausführungsbedingungen nicht zufriedenstellend" CanClip von V120 bis V190 mit original RTL2002. Immer die selbe Meldung. Hab ich was übersehen. Gibt es noch einen Trick?

[@tijmeng8550]

Heb jij tips voor het inleren van de quickshift module? Dat kan met CAN CLIP toch?

[@likewin3775]

Kan je dat ook met kaarten die niet meer herkend worden? Auto heeft 2.5 maand stil gestaan gevolg accu leeg. Na het opladen worden ze niet meer herkend en blijft de startonderbreker actief.

[@jedandva7492]

Recently I bought Renault Can Clip diagnostics (Chinese clone, not the cheapest, but better version, with golden (fully yellow) board, Cypress chip). Everything seems to work fine, but when I come at step "card programming" (3:50 minute on the video) I'm missing that option. Instead of SC010 button/option (card programming) I have another option SC006. I'm not sure what is the cause. I tried more Clip versions, same on all of them. Tried more cars, same... Or it's up to Clip diagnostics, but I repeat, it's better version, not the cheapest one?? What can I do now? Should I maybe buy a Renolink and try to program in it? Or should I buy something else? Thanks in advance

[@efraxii]

This method works for renault megane/scenic 1 ph2 with keys?

[@digix205]

thanks. i did it a few times on my laguna. but will it work on megane II also ? and does it need 23 or 24 byte ? thanks

[@majidradouane5346]

Hello ,and thank you for this video,please i would like to know wich canclip we need to do this ?,thank you

[@SleepyBearAngomer]

Why 5938 not correct on ver212?

[@hrauto5551]

you can program a new key without a functional key ? ( in case of lose for example ) ???

[@adeemigbareya2906]

Thank you for the video. Does this work with Renault Megane II 2005?

[@jairoquiroz4624]

My question is this process'm not doing well? or is there some other prorama to schedule those keys of these models? or serves for all models

[@haydonjean]

hey mate, I bought a 2005 renault megane estate and it has this key.i hot only one and here are too much expensive.can you put down the descriptions from where to buy the adapter to connect to pc and car and where can I get the codes pls? thx for the vid mate.

[@user-dj8nz4rq3d]

Тоже так делал только старая карта теперь не реагирует авто не видит. В чем дело может быть

[@nicohaasnoot319]

Is die code altijd 5938? Wat is techline?

[@keesbolier3611]

Hey Capske, Ziet er goed uit de tutorial maar werkt dit met elke can clip er zijn nl ook Chineze versies te koop voor een fractie van de prijs

[@robbocop33r12]

What voltage does the battery have to be to do this? I keep getting a message saying voltage isn't high enough to continue, and that's with a battery charger on it!!

[@jucaspt]

This works in megane 3??

[@salamboy200]

good job Thank you for the video. Does this work with Renault Megane II 2005?

[@michielbroek5702]

Ziet er goed uit! Wil je mijn kaart ook inleren tegen vergoeding?

[@jairoquiroz4624]

good evening friend, works for me perfectly with Megane II but I uiero know how you do it for the Clio, Symbol, Kangoo models, since I fart to make the code book but when I will transform the Renault Pin Extractor tells me wrong code, you could help me in the Renault Pin extractor tutorial she tells me to take starting from 18 to 23 in some cases up to 24 m

[@sangjinho5847]

hi Your Renault video is great! Do you know how to program Renault Cruise Control Speed ​​Limit? If you know, please ask for a video or explanation. I need the help of a professional like you. plz...

[@crigeorge9549]

Capske Uploader is it true this method is not working with 2006 up models?

[@raucousrowdy6540]

Which software version are you using? Is it V146?

[@hamidoucheahmed9145]

Anyone know how to creat a New uch program because mine became Virgin !??

[@haydonjean]

also where to buy key cards pls?

[@mustaphaalaoui4454]

Hi brother can you giving me a software of can clip and renault key extractor thanks a lot

[@nicohaasnoot319]

Hoe kom je aan die Renault Pin Extractor?

[@thedronezone4924]

Hoi Nico, Weet jij ondertussen waar die pincode extractor te vinden is ?Groeten,Rudi

[@wouterheijligen7785]

Does anybody know which bytes to take for a Megane 2 from 2007, Pin extractor says invalid ISK when I take the bytes 18-23. When I select Laguna 2 it generates a pin code, but when I get to the point where I need to put the incode in can clip it gives an error.

[@Carsbyduno]

Hi Wouter, I don't think it works for cars after June 2006 (although I never tried). This method works for met with an 2005 Espace, and 2004 Laguna. Works well with renault Pin extractor 2 (although it was a pain finding it). Did not work with the renault clip tool, couldn't get a valid outcode.

[@hantherio]

Grate tutorial, can you please share the Renault Pin Extractor?

[@capskeuploader3982]

drive.google.com/file/d/0B1PkCwRYB48WTF8xZ3N1R25nakU/view?usp=sharing

[@franciscoadrianvives4104]

hello someone knows how it is done to megane phase 2 or 1 immobilizer system code is entered I is the code book request 1 pair coding keys

[@1Albis]

Your OBD Cable genuine or china?

[@robbocop33r12]

I've just tried to do this with my 2005 renault megane, everytime i try it clip says insufficient battery level to continue, this was purely on standard battery power. Spent £300 on a quality used battery stabiliser, set the voltage to the battery at 13.8 volts, still didn't work, then 14.2 volts, still didn't work, then 14.5 volts!! Still Renault clip says insufficent voltage to continue, what the hell??

[@83Sogron]

Hi, the battery in keycard, not the car battery!

[@robbocop33r12]

@@Rassettaja yes,it's nothing to do with the key card battery,its the actual vehicle battery voltage that is shown in Clip software. Anyway,i purchased a Lonsdor k518,took me about 30 seconds to programme two key cards!:-) No faffing about worrying about battery voltages!

[@83Sogron]

@@Rassettaja Yepp, my bad, btw u need to switch off the ignition by double press the start button, than u ll be able to program the card (in this video we see a laguna, where if u remove the card u switching off the ignition).

[@ADAMMCCR]

Unfortunately doesn't work for cars after June 2006 as vin needs to be pre programmed to key .

[@lukazazvonil5627]

Yes I have problems with Espace 2006, it works till the end, but says wrong number at the end

[@adeemigbareya2906]

Update: I can confirm it works with Renault Megane II 2005. I used programmable keys from eBay and they work flawlessly.

[@robbocop33r12]

How did you keep your car battery voltage up while doing this? I have same car, but a 2005 rs225.

[@yousifmorsy6511]

Please give link to download renault pin extractor

[@lvypaul_ro]

Does anyone know other code for SC003? For me 5938 does not work.

[@czvlada]

Hello, did you solve the problem? I'm dealing with the same thing, thanks

[@mostafadardeer9645]

I have the same problem, did you solved it?

[@chaveirojacui5065]

this tool its genuine or buy in china?

[@Kamadev888]

what if you don't have a working key card?

[@capskeuploader3982]

This is what i found in my documentation:In the case where all the keys are not available, it will be necessary to achieve a reassignment process thereafter with all keys. Enter into dialogue with the system "Kill". In the "Command", "Command specific "validate the line" SC028: learning key cards. " The tool displays "Remove the key from the ignition theft. " The tool displays "Please enter the code after sales." Contact coupé, enter the secret code aftersales (12 hexadecimal characters) and confirm. The tool displays "Attention, following keys not shown will no longer be active. Restart the procedure to reallocate "learning is ongoing. The tool displays "Insert the key into the ignition lock and turn the ignition and confirm "to contact with a car key or key blank. The display shows "1 learned key", then confirm, then "remove the key from the ignition lock." The tool proposes "Do you want to learn another key? ". To assign additional keys to the contact for a few seconds with the other key affect vehicle (maximum four) then validate. The display shows "2, 3 or 4 keys learned" and "remove the key from the ignition lock." WARNING: these must be old car keys or new keys unencrypted. The tool displays "Writing data in memory" UCH is encrypted and the keys are affected. Several seconds are required for this message to come out of the reassignment

[@capskeuploader3982]

Hi everybody, sorry that i never replied to your messages. I posted this vid because i had to do a lot of searching before i was able to program this keycard.It's rare that i check this post out thats why i never replied.I'll try to check this out a little more, but don't expect to much, cause i'm not a pro.

[@jairoquiroz4624]

ok I understand, only necsito know if this Renault program pin extractor works for meters models such as Symbol, Clio, Scenic, I would like to know l protocol, since in this case the scenic, entando in the reserve starts from the bits 3 to 21 I pegunto from where I take it, because in this case you samples taken from 18 to 23 now the question in the scenic starting from the bits 3 and ends at 21 where or starting from where I take you, I appreciate what you can help

[@capskeuploader3982]

The 1st, 3rd and 5th row indicates wich byte is in the 2nd, 4th and 6th row.So i'll give the values from bit 3 to 21 from the video so you can reference:1 2 3 4 5 6 7 8 9 10 11 12 1ST ROW > 73 59 38 56 E0 4B 36 0B BA 4B 2ND ROW13 14 15 16 17 18 19 20 2122 34 24 3RD ROW36 00 00 00 00 48 FD A3 95

[@capskeuploader3982]

Sorry can't align the teks correctly. Send me a mail on [e-mail] i'll show it on a photo.

[@jairoquiroz4624]

hello, greetings, ok my email is [e-mail], this is my case with scenic me the pattern starts from 3 and ends at 21, so as shown in this example: 3 4 5 6 7 8 9 10 11 BA 08 AA 47 80 03 D6 F9 12 13 14 15 16 17 18 19 20 21 AC B5 36 40 1E 00 00 27 2C 00 I wonder from where to where I take bits in the case of video taken from 18 to 24 in this model where should I take it? thanks for the attention given no leave my mail and more then when I get to my studio I send photos of the process with the probe clip and so to better explain what the case, I hope you can help me, I have the pin renault extractor and I already have the first card megane II as such you explain in the video tutorial, I want to apply for other Renault models thanks again

[@milee95]

could used card from another card be programmed also?

[@thedronezone4924]

Hoi Capske, Ik vind de pincode extractor nergens meer zonder scam&spam... Kun jij me eraan helpen aub?Grtz, Rudi

[@capskeuploader3982]

deze zat bij de software cd die ik kocht. Op mijn laptop draait geen antivirusprogramma want ik gebruik deze enkel voor autosoftware dus kan ik je niet bevestigen als er scam of spam inzit. drive.google.com/file/d/0B1PkCwRYB48WTF8xZ3N1R25nakU/view?usp=sharing

[@RK-fp7ob]

geeft trojan horse aan... met eset nod32

[@GMiguel92]

Hi, thanks for this tutorial. Can u please explain how u put can clip work with windows 7? i have a windows 7 ultimate x64, install Can clip normally, but when i connect the clip, i can't install because the drivers don't work. With windows xp runs perfectly.. Can u give me a tip how to put it work with my windows 7 x64?? Thanks

[@gastondvt]

Hey my friend, it doesn't work with Win7 x64, just it does with 32 bit version. I had the same situation :)

[@GMiguel92]

Hello, with win 7 x86 (32bits) works good? The drivers are the same that came with the DVD software?? Thanks for the information

[@gastondvt]

+Gonçalo Miguel yes my friend!

[@GMiguel92]

+gastondvt thanks!!!! Now I just need to find the Renault pin extractor. Any idea when I can find it? I searched about this software but I can't find it

[@gastondvt]

Hey my friend. You just google it, you will find a forum where you can download a list of links. Many of the won't work but you can find one that works!

[@kaovi1978]

Great! Thanks

[@elliteauto]

nice

[@nicohaasnoot319]

Pin extractor: moeilijk te downloaden, allemaal virussen komen mee.

[@kaller.9440]

Ab 08:12 ist das Video Schwarz. Da fehlt leider was.

[@capskeuploader3982]

Can Clip V120 capske.stackstorage.com/s/khoi5nifui4rBlPb Immo Code + reprog v111+ radio preprog capske.stackstorage.com/s/qamwCZXoSGB6q4X9

[@amliru4074]

Неплохая копия со 156-ой прошивкой: ali.pub/slw4f