Repair Bodyboard How to. How to reattach the foam of a Boogie board so it will stay attached in surf

How to Repair a bodyboard. I show you how to reattach the foam of a Body board that will stay attached when you surf.
I show you the inexpensive glue that is best for the job
Affiliate Links:
Small Tube Adhesive: amzn.to/2M35oE9
Large Tube Adhesive: amzn.to/38APUyX
Replacement Wrist Strap: amzn.to/3pildVU
Board Swim Fins: amzn.to/2WKyJp1
Buy a New body Board:
Cheapy: amzn.to/3aHy9k5
Nicer Board: amzn.to/3mSWjdQ
Quality Board: amzn.to/3mRonya
A viewer told me I needed to add a link so people could buy me a Beer or Coffee when they are so helped, especially financially by my videos, so here it is Thanks 😃: www.paypal.me/...

[@travisj2695]

Silicone adhesive would probably work better and less messy

[@Marksreviewsandtutorials]

Yeah tried that and it (Silicone) came off instantly. MRT. I mentioned that in the video.

[@patefutch6168]

I’m a surfer but I will use body boards certain times certain spots. Anyway I HAVE BEEN looking for a video to repair or replace the bottom part of a morey it’s like fiberglass? A large section came off and it was real brittle but I want to know what i can do to repair it because it’s in great shape other than that

[@bluefletcherfish]

The construction adhesive I used (liquid nails) dissolved the foam of the board! 😠

[@Marksreviewsandtutorials]

Yes some foam is like that. Sadly some boards have very poor quality foam

[@rafaelflores9444]

@@Marksreviewsandtutorials use a heat gun

[@ceeweedsl]

@@Marksreviewsandtutorials No, it's not the quality as in good vs bad, but the type of foam. Many construction adhesives will dissolve certain foams. Choose one that indicates it's good for foam. They actually say so on the label or in the name.

[@stevereynolds1407]

Thankyou Cheif!: 🤙

[@andyandcait]

I'm curious, how did this fix hold up over time? Does the construction adhesive hold long-term?

[@Marksreviewsandtutorials]

Held up great 👍 Still solid after multiple trips to the surf

[@gunnarmoeller8606]

Using the same stuff to fix tailpads on Surfboards. It does do the job. Only problem is it's to sticky to get an even spread for larger areas, like foamboards before it starts drying (which is probably less than a minute).

[@nicolasbrun9795]

I have a table that bent. the tail and the front touch the water. He lost the rocker, it is flat but the nose bends in the water. How can i fix this? I am afraid of using heat and that bubbles will come out or it will come off. I don't know if it has a string.

[@rafaelflores9444]

tiene rocker negativo. para invertir el rocker, se mete a un horno de aire caliente y al salir se forza un poco hacia rocker positivo (pocos segundos dentro del horno ) muchos no tienen solucion

[@xmtlrt]

I have attempted this on my soft top SUP! Really hope it works!!!

[@ceeweedsl]

BIG ISSUE with construction adhesive and foam is that often the solvents in construction adhesive will dissolve foam. Two things you can do: 1) hope you get lucky like Mark's reviews and get a safe combo of foam and adhesive. 2) look for foam-safe construction adhesive - each brand makes a version to work with foamboard. They are usually latex based, no solvents. Locktite PL-300 is foamboard AND exterior rated, so I'll go for that one.

[@joshuaortiz5754]

Any videos on painting or dying the foam part

[@rafaelflores9444]

don't use any kind of glue pleaseee use a heat gun

[@federicomuller5348]

My daughters bodyboard got bubbles and I cut them in squares, remove de square part of surface foam, added liquid nail just for foam and waited a whole week for it to dry and today we went to the beach and guess what the garbage did not stand the water it got like if I had just added it so it does not work and I am gonna try with hot glue intead next time

[@rafaelflores9444]

todos los componentes se soldan con aire caliente

[@SooLabs]

What's the hard bottom made of?

[@shmorkshmire]

I've got a couple foamie surfboards that I want to fix up. The foamie top layer came off from the styrofoam. I have two questions: 1. Is your boogie board made of styrofoam? (It looks like little balls of foam) 2. Is there resin in the liquid nails? Does it say polystyrene or epoxy on it anywhere? I'm asking because my boards are styrofoam inside and polystyrene will melt styrofoam.

[@thee-edd]

As long as its pu adhesive it wont melt the eps expanded poly styrene or styrophoam as you call it i use CT1 grip and bond adhesive or puraflex 40...hope this helps

[@ImLivinSD]

Great Video, Thanks for this as I have a few boards that I paid over 100 bucks for but they seem to delam just like the 30 dollar boards. Great DYI fix. Thanks Again.

[@Marksreviewsandtutorials]

So glad it helped.

[@thomdrum]

Hot glue gun Painters tape But if this glue is safe for the foam core-cool!

[@rafaelflores9444]

trabaje en una fabrica; todos los elementos se pegan con aire caliente. usa una heat gun

[@leo-stief]

You just saved me 80€ Thanks a lot!

[@Marksreviewsandtutorials]

👍

[@gravymatt]

Thanks!! I am going to be doing Liquid Nails construction tube on the bottom slick this weekend. Also, just sharing ebodyboarding had recommended hot glue in their video kzbin.info/www/bejne/b2Snq2Wko76NgcU&feature=emb_title