Repair & Fix Speaker/Make Voice Coil at Home

Repair & Fix Speaker/Voice Coil at Home.
In this video,I have repaired a very old,almost 25 years old loudspeaker at my home.Speaker's parts such as cone,spider,dust cap that I hardly found in the market but I could't find Voice coil and rubber gasket.So,I have made voice coil at home using thin paper and with 37 SWG copper wire,and gasket using pressure cooker rubber gaskets.
Other materials that I have used here:-
Fevikwik Adhesive Glue
Quickfix Glue
Epoxy Resin AB Glue
Transformer Insulation Paper (Thin Type)
Glue Gun Stick to remove metal dust
Music in this Video:- Bright Eyed Blues (Unicorn Heads)
• Unauthorized downloading and duplicating on KZbin channel and any other media platform is STRICTLY PROHIBITED and will lead to punitive measures.
Please Like & Subscribe to our channel &
Click The Bell icon to get new Video Updates.
..... Thank You .....
#RepairSpeaker #MakeVoiceCoil #HomemadeVoiceCoil

[@ReshamNepal]

धेरै राम्रो भिडियो बनाएर देखाउनु भयो दाजु, अनी यो स्पीकर को जाली च्यात्तीएको हुन्छ नी यस्लाई बजार बाट किन्नुपर्ने होकी, या घरमै बनाउन सकिन्छ भने यसको तरिका पनी सिकाउनुहोस ल।

[@TMCreations]

यसको जाली (स्पाईडर) बजारमा पाउन सकिन्छ ।पाईएन भने घरमा बनाउन पनि सकिन्छ । भ्वाईस क्वाईल चै बजारमा पाईदैन आज्कल स्पीकर नै पाईन्छ नया नया ।तेही किन्नु उत्तम हुन्छ ।यो चाही एन्टिक सामान भएकोले मर्मत गर्दै राखियो ।पुरानो चिनो ।

[@Tomsfundubs]

Fool using sticky tapes causes the balance of glue affect the movement of coil it means it influense performance

[@TMCreations]

Thank you,but actually cellotapes does not affect so much than using pvc tapes.PVC has more glue and so I did not use it.

[@NewEraCollection]

Derai Ramro wow

[@petec6690]

Good video all the way up to the end, then a let-down. Would have been nice to demonstrate some music so we can see how clean it sounds. All we know for sure is it hums.

[@TMCreations]

Thank you....here is some demonstration at 3:45, kzbin.info/www/bejne/sKjMXp-qrd1sp6s......

[@chetanpatil1755]

Time pass

[@AllboroLCD]

I am interested in re-winding bad voice coils, would have been nice to show how the coil was wound. Also how much length is needed to make either a 4 or 8 ohm coil!!!!!!!!!

[@TMCreations]

thank you,you should mark only half length of coil moving height,half for movement.find out the depth where coil moves,and than mark at half length,and that is perfect for coil winding.

[@AllboroLCD]

@@TMCreations I was about to, but then found myself a replacement that matched. it was 1 inch x 1 inch, 8 ohms, and had only 25% of the former wound with wire. Is there a set length to get 4 or 8 ohms or does that vary?

[@pankajseth09]

Turn

[@TMCreations]

Calculate the length of wire required by the resistance (4ohms or 8 ohms).Then you can make turn on half of that measurements.