Moment på skruvar på Stiga Park. Workshop Manual Stiga Park General tightening torque Unless otherwise stated the following tightening torque are applicable for screws and nuts on the machine. General Thread/Torque on Siga Park Senator, President, Royal etc according to workshop manual M5 - 5 Nm, M6 - 9 Nm, M8 - 22 Nm and M10 45 Nm. Happy repairing! 😅
@berg310tor-arnejonasson8Ай бұрын
Tack ska du ha!
@willybaldsirhenry Жыл бұрын
Wow many thanks for this video. I always wondered what the K46 looks inside. Incredible level of information.
@berg310tor-arnejonasson8 Жыл бұрын
Thanks a lot
@aksuli112 күн бұрын
Hi, my stiga park comfort doesn't move well when cold. Is it cos of old transmission oil? And where's the draining hole for that? Thanks.
@berg310tor-arnejonasson811 күн бұрын
I would start with changing oil and oil filter. The drain plug is in the center of the gearbox, you can see it in the video
@aksuli111 күн бұрын
@@berg310tor-arnejonasson8 You mean motor oil? My model is 2006 and bought it as used past summer. Haven't changed any oils yet but air filter. It doesn't have oil filter.
@berg310tor-arnejonasson811 күн бұрын
@@aksuli1 No I mean gearbox oil, there is a filter inside the the gearbox (Tuff torq K46) but you have to disassemble the Tuff torq K46 to get to it, like in the video…
@aksuli111 күн бұрын
@@berg310tor-arnejonasson8 Ok thanks 👍. But you don't have to dismantle all the parts just to replace the filter, only the cover?
@berg310tor-arnejonasson82 жыл бұрын
💥💥 Please subscribe and press the like button ... 🙂 and if you want, please write a comment 😁 💥💥 💥💥prenumerera gärna och tryck på gilla 👍 Och om du orkar så skriv en kommentar 💥💥
@PierrePouliot-u1y Жыл бұрын
thank you , it help me alot to fix my transmission
@berg310tor-arnejonasson8 Жыл бұрын
Thanks! Nice that it helped a little
@igormoeller2 жыл бұрын
Very nice teardown..and good info..my k46 suffers simmiliar (loosing some power when really hot). I wondered if pumps could get machined to remove marks..and you answered that question (i would hate to buy rebuild kit - costs a fortune ).
@berg310tor-arnejonasson82 жыл бұрын
Thanks and good luck!!
@vanover69 Жыл бұрын
Great video. I have a question you might be able to help with. I have a 1990 Ariens tractor that is have a issue. The mower wont move forward and make a whining sound...it move backward strong and fast...just not forward. The belts seem to be tight, the fluid seem to be full, the linkage seems to be moving. The mower is in super good condition and hope to save it. Any help would be great...Thanks
@Tinyhomefixers3 ай бұрын
Min kasse har ingen drivning längre. Saknade inte olja. Filtret såg illa ut. Kan det göra så att man tappar drivningen? Undrar oxå på om drivningen kan justeras med den bulten som har fyrkantig bult huvud med en låsmutter på? Tacksam för svar
@charliekyriacou62157 ай бұрын
Great video! one question: What did you use to polish there center base plates?
@berg310tor-arnejonasson87 ай бұрын
I have a lapping machine at work, manual but high precision
@blainemcmillan6228 Жыл бұрын
My mower loses power when hot to wear it will barely even drive I'm at the point where I need to tear down this transmission I'm not sure if it could just be a clogged filter or if maybe there's a problem with the axle seals. When I change the oil in it it was very very hard to fill up the transmission again because it didn't want to take any oil I had added a little bit at a time and it took me a whole day to get a level back in it I'm not sure why that was. Do you have any answers or advice
@berg310tor-arnejonasson8 Жыл бұрын
Hi! To fill the oil faster you kan remove the plastic plug as shown in the video, this vill make it in a few minutes. About the drive it sounds like the there are some scratches on the hydraulic pump or motor. Then it needs to be reworked. Best regards Tor
@sshvulnerability5 ай бұрын
Can you show the process for polishing the pump?
@Tinyhomefixers3 ай бұрын
Jag vill gärna också se det🙏🙏
@berg310tor-arnejonasson821 күн бұрын
Sorry, I don’t have any video of that, but I am using a face polishing machine at work
@danielnorinjanson56472 жыл бұрын
This really helped me a lot! Thank you so much dear Sir!
@berg310tor-arnejonasson82 жыл бұрын
I am so delighted to be able to help!
@csanivehrer47775 ай бұрын
Hi! I made the rebuild but when i use the mower the forward end the backward exchanged?! What can be the problem?
@berg310tor-arnejonasson821 күн бұрын
I mention that problem in the video, it is the wedged plate that is mounted upside down
@almantas1992076 ай бұрын
If my lawn mover after moving up all to one side iand after putting back to driving position is starting to drive heavy and i heard the sound so it means that oil is missing or there is more trouble ?
@berg310tor-arnejonasson86 ай бұрын
It’s very difficult to say with out knowing what kind of gearbox and drive it is
@KaiserBlade4 ай бұрын
I wonder which bolts were to drain the oil?
@Ekmanjohnny7 ай бұрын
Jag har en stiga tornado 2098 från 2014 och har märkt att den är väldigt trögväxlad. Det är ju ingen hydrostat på den men finns det olja eller fett i den transmissionen?
@berg310tor-arnejonasson87 ай бұрын
Hej! Ledsen men jag har ingen aning, har aldrig tittat på en sådan. Mvh Tor-Arne
@travisbacon55272 жыл бұрын
Would have like to see how you polished the pump. That's like the main issue.
@berg310tor-arnejonasson82 жыл бұрын
Well, I agree that it would have been nice to see but it’s quite simple. It’s just a face honing machine with a manual pice holder. But I did it in the factory wher I work and ther is no photo or filming allowed So sorry about that!
@keithmeyers3718 Жыл бұрын
Is any way to polish the surfaces by hand?
@berg310tor-arnejonasson8 Жыл бұрын
It depends on the damage, if it only scratches it can be polished by hand. In other cases you need a good lapping machine
@Knolle182 жыл бұрын
Thanks for your documentation about disassembling the transmission! Am i right, that you filled it up to the top With oil? I Saw some other Videos about changing fluid and they used about 2 Quarts (2 litre). Thanks for your work and keep up the work and swedish talking in the background. Always nice to have friends around while working on engines and other things
@berg310tor-arnejonasson82 жыл бұрын
Hi! And thanks for your comment. In this drive it should be filled with oil and then on the lawnmower there is a small container that shall be filled. Unfortunately I don’t know how much oil I filled because I used a pump. But any way this one should be absolutely full Thanks and have a nice day!
@mikaelkarlsson3212 Жыл бұрын
Vad var det du gjorde med pumpmotorn mer exakt? Mvh
@niklavsciss82562 жыл бұрын
Hello, what oil you used?
@berg310tor-arnejonasson82 жыл бұрын
Hi, I used Standard 10W30 oil. And have done so for many years
@dannyboy5300 Жыл бұрын
Hur mycket olja går det i ungefär ?
@PeterSiekiera8 ай бұрын
Great video
@berg310tor-arnejonasson88 ай бұрын
Thanks a lot!
@SuperFkv Жыл бұрын
Thanks for the video . Greetings from Denmark . I subscribed 🤗