Repairing Saeco Pressurized Portafilter for Semi-Automatic Models

In this video you will see how to replace Full Repair Kit for Portafilter.

[@viktorostapenko2172]

Thanks a lot! There are so many small but crucial details to correctly assemble the portafilter. Very helpful video!

[@Fabiopeli]

Thank a lot!...I dissasembled this portafilter to clean and since 2 month haven´t assembled...today I did it and is working again

[@wolterl9899]

Not difficult but thanks.. it help just for info for the disassembly, with this change i can save some money

[@tgeorges]

Thanks so much. The step I was stuck on was how to assemble the large round metal ring onto the plastic. One thing that was difficult was snapping the plastic assembly onto the nozzle of the inner rubber disk.

[@potsy72]

+Dan Pinson thanks for the socket tip! i kept assembling it, and taking it back apart because the handle didnt snap back...the rubber wasnt all the way through the plastic assembly.

[@cristianbelteu1659]

that step takes a bit of force and I was afraid to hurt the assembly

[@mogtholin]

7 years later and I was stuck in this exact step, thank you so much for the video and the comments!

[@michelegalli2453]

grazie Miroslav l'ho sistemato!!!

[@classe3hliceoe.majorana828]

Grazie per il video postato, mi stavo impazzando a montare la molla di torsione, ma grazie a te è stato tutto semplice.

[@volodyahristov832]

Благодаря ти Миро, и на мен ми помогна. Трябва да взема и да имам комплекта части след време от твоята страница. Приятен ден

[@miroslavstoicev8821]

+Volodya Hristov Винаги сте добре дошъл, радвам се, че успявам да помогна на хората по някакъв начин. :)

[@raymondlemieux740]

Thanks for explicit video Made assembly easy

[@portioliluca]

grazie per il tuo video , ho salvato la mia gaggia !!!

[@ganso55555]

FANTÁSTICO! Justo lo que necesitaba. Gracias!

[@radoslavjordanov6872]

Много ми беше полезен, благодаря !

[@videolaulau2012]

Merci beaucoup, j'ai pu réparer ma cafetière qui n'avait pas servie depuis longtemps

[@daichd2322]

Thank you very much, you just saved my day

[@GauGuyGau]

Great video! Oddly enough I had the same problem as the top comment... I put back the spring several times, would line up the indents and click everything into place but the plastic with the valve would pop out. On my last try, instead of lining up the plastic valve to all the holes in the stainless steel piece, I shifted it to the left, (so not all lined up with the holes/indents) so only 2 holes are lined up and so far so good, works as good as new. go figure.

[@ernestozuffada5069]

Grazieeee 🤗

[@HVM4244]

Thanks brother, very cool. Now I can enjoy some espresso.

[@lucesainte-marie9017]

Hi Miro. Without even realizing it, I used your video to replace used portafilter with the kit I received today - Searched KZbin and your vid was the best. Me not noticing who had made the video. Everything went well. Now it is two hours later. Went shopping etc. etc., came back on Internet and got to visit Sophia, typed your name haphazardly and here you are. I am happy that you showed me 'personally' how to do the repair job. It was nice being in contact with you. Our first coffee will be for your and yhour family ! Cheers from Eastern Canada :-)

[@jme9811]

You are the best, many thanks

[@user-me5ow5zg8z]

Σ ευχαριστώ πολύ αδερφέ!!! Μ έσωσες...

[@nitakuma]

Thank you for posting this! I have amazing espresso again!

[@miguelrrc]

exactly what i needed, thanks

[@patricksurmont8047]

Thank you. Very use-full and well done video8

[@josephlinville]

Almost the best video ever.

[@vipehp6223]

Very helpful thanks!!

[@mic2fra311]

Thank you very much. I was going crazy.😆

[@chinoixchinoix]

Thank you❤

[@katalinbalazs2214]

Thank you so much, it was/is a very big help!!

[@ADVnoke]

Great... Thank so much 😉👍

[@maxm06]

you save my pormia je.. je... !!! Thank you

[@kowalja6]

Thank you!!! You saved my day :)

[@PsPsPsNs32]

Thanks! this video helped me a lot

[@jangorczyca5830]

Thanks a lot, helpful movie.

[@antoniocacho5884]

Gracias, excelente.

[@johnnyjimj]

Just to make sure I got this right - the rubber valve plate ring is placed with the taller side towards the basket, or towards the holder (because the video is a bit blurry, I couldn't make it out clearly)? Placing it teh wrong way would position the valve plate differently and change the valve opening pressure...

[@cristianbelteu1659]

thick side up, toward basket

[@giusipirrone8414]

Grazie mie stato utile o risparmiato 25 euro 😁

[@antoniocuomo52]

Hi, great 100% explanatory video, I wanted to ask you where to find the spare parts for the arm of the gaggia style (exactly the same as the one shown in the video. I subscribed to your channel and liked it.

[@alexandrey10]

thank you~!

[@eppalomino]

excelente . gracias

[@LM-mq2pj]

Can I make this into a non pressurized portafilter my just reinserting the small wire around the top and leaving everything else out?

[@peas4snaks]

Any ideas on why coffee would be pouring out of the 3 holes where the screws are? I can imagine it could be that the valve gets stuck. But otherwise?

[@BobbieGWhiz]

What’s the purpose of the handle that is spring loaded and wiggles back-and-forth several degrees? Before replacing my original portafilter(Estro Vapore-predecessor to Starbucks Barista) that handle didn’t spring back. You kept the handle to the right until the pressure built up and the motor tone changed pitch. Then you move the handle to the left to allow the espresso to flow out. I don’t understand the purpose of the spring loaded handle in this current portafilter. As it’s designed it always springs back to the left. I tried holding it to the right, but that did not prevent espresso from flowing out.Thanks.

[@alexandruoprescu6808]

Great video and very helpful.where can i buy the reparation kit from, please?

[@reyestembleque3256]

Ola , por favor el alambre que va donde se echa el café , como va , ? Gracias saludos

[@Merabashnik]

Thanks a lot!!!

[@galushin73]

Thank you

[@sanabraxas87]

Thanks A lot! quick question. Im missing one of the three screws on the bottom. Is it going to affect the functionality? thanks!

[@agusgebhard]

Hi! Thank you for your video. Could yo tell me de type and size of the very fine wire shown in the firts picture, not the one with the loop. Thank you! I’ve lost it!

[@antoniocuomo52]

Hi sorry, but I forgot to tell you that I live in Italy, you know where to find arm spares in Italy. Hello and Thanks again

[@iceoue]

First you need to install the mechanism with the valve in the body, and then insert the plate. This is much easier to do and there is no risk of breaking the mechanism.

[@sauliuspaulauskas7798]

super video

[@marybacchini8035]

Great video,I need the little spring, first one you installed. Where can I get one . Thanks

[@miroslavstoicev8821]

You can find whole here: www.ebay.com/itm/Saeco-Parts-Full-Repair-Kit-for-Pressurized-Portafilter-/400775821203?rd=1 or in my eBay store: stores.ebay.com/miro1976

[@tgeorges]

I got just the large plastic pin support and small cam spring - that's all I needed - from Phillips directly. If you need parts for the Poemia, this is a great source: www.buyphilipsparts.com/model/SAEHD8325|47/_/_/Saeco/HD8325|47/Saeco_Poemia_Manual_Espresso_Machine_Class

[@skilledhiko329]

Thanks Moro. The video is very instructive. But still I have a question this portafilter is affecting the espresso quality or not? Because when I open it it gives no crema at all, for second trial of open the portafilter and reassemble it it’s stucked.

[@wolterl9899]

if the coffe stuck take a look at the spring

[@danm3188]

hey. My portafilter handle broke. It still works, I just have to grab the filter part directly to screw it in or remove it. No easy task when it pipping hot. Anyone know if there's a way to get JUST the plastic exterior+ handle for a Saeco Via Venezia portafilter?? Didn't really want to spend $60 on a whole new one when all I need is the plastic frame. ie. in this video at 3:00, the part on the table framed between his wrists.

[@lowweeyien1014]

Anyway to reverse if I accidentally used Cafiza and caused the metal part became oxidized.

[@remyschmidt8540]

das good bro

[@RENEDU2]

02:35.. the mistery solved!! ...blagodaram

[@maxsimon9616]

What is the name of just the white plastic piece?

[@antonio613]

what symptoms would require repairing Saeco Pressurized Portafilter?

[@David-bo2cb]

at 3:00 to 3:15 the video is deceptive as regards the amount of force that needs to be applied to seat the white plastic device into the holder. see kzbin.info/www/bejne/g3TJkK2Fer2Chrs at ~7:00 for a more useful guide how to get it to seat.

[@vicente157]

MUY BIEN HASTA QUE EL MINUTO 4,37 SE METE LA PATA .... PUES NO SE VE SI ES UN A PESTAÑAM, O DONDE Y COMO, DE AHI HASTA QUE CIERRA... SE CARGA PARA MI LA ENSEÑANZA.

[@Fernando-bt6lg]

Donde puedo comprar la válvula blanca del portafiltros

[@cristianbelteu1659]

coffeesection on Amazon.com has some kits

[@luize3202]

3:11 why does it go on so easily mine doesn't at all

[@michelebattista8212]

Buongiorno,io non riesco a inserire la valvola nera nella ghiera bianca, qualcuno può aiutarmi? Grazie

[@didierfortez8399]

OU TROUVER CE KIT MERCI

[@steelgtr]

Where to buy parts??

[@cristianbelteu1659]

coffeesection on Amazon.com has some kits

[@n3ssaya972]

Just take it out, pressurized portafilters are SHIT.

[@vebruno]

Excellent video, good explanation. but unfortunately here in Argentina you can't get the parts🥲🥲