Tap to unmute

Replace BAD bearings in a DW 5000 double kick pedal - step by step how-to

  Рет қаралды 7,711

Meshem Jackson School of Drums

Meshem Jackson School of Drums

Күн бұрын

Пікірлер: 30
@jross3680
@jross3680 Жыл бұрын
Dude, thank you so much for doing this. You are the man. I just rebuilt my DW5000 double pedal from 1999 following your video. It came out perfect. The bearings were all gummed up and seized, now, it is smooth like the first day I bought it.
@MJSchoolOfDrums
@MJSchoolOfDrums Жыл бұрын
Sweet dude! Glad I could help 🙌
@petethedrummmer
@petethedrummmer Ай бұрын
Thanks so much for this! I didn’t see the retaining ring. Those pliers are nice to have when you need them.
@Jason-wc3fh
@Jason-wc3fh Жыл бұрын
So I have a good background in mechanics. I would like to add that using a hammer to get the bearings out is perfectly fine for when you have no intention of reusing them. The impact shocks of hammering can cause microdents in the bearings themselves that will cause friction. Yes, the use of rubber/cloth helps minimize that tremendously. What I would suggest that any DIYer can do to install new bearings without needing to hammer them back in is to purchase a proper sized threaded bolt that will fit directly through the bearing opening and is long enough with enough threads to extend the entire length of the opening into the pedal plus extra. You cannot go too long. Buy a couple nuts and several sized washers of different outside diameters that fit through the bolt. What you can do with this is make a bearing press. It works extremely well and is actually quite fun watching the bearing slowly thread right into place while you're rotating the bolt. You can even use this as a bearing puller. The best way to make it easy on the bearing is pressing it in by the outside race. Many people will even have a socket set of the right size that will work. The socket has a hole on the end where a bolt can slide through and be used to press it in.
@MJSchoolOfDrums
@MJSchoolOfDrums Жыл бұрын
Thank you for the insight! I just grabbed what I had to work with. But you make a valid point and a great suggestion. Thanks again!
@TheSkidaddle
@TheSkidaddle Жыл бұрын
Thanks for your video. I was stuck in the disassembly of my pedal until I watched it. Finally I was able to take up the slop in the far right bearing that was causing a rattle/buzz. Now I can move onto the same problem with my DW 5000 Single Chain/wire base Bass Drum Pedal.😏
@MJSchoolOfDrums
@MJSchoolOfDrums Жыл бұрын
Glad it helped! 👊
@B.Cote39
@B.Cote39 9 ай бұрын
thx so much man!! so few resources available !!!
@MJSchoolOfDrums
@MJSchoolOfDrums 9 ай бұрын
Glad I could help!
@joecoleman288
@joecoleman288 10 күн бұрын
I have an older 5000 and it has a single chain drive. Any way to convert it to double chain like the one on the video?
@MJSchoolOfDrums
@MJSchoolOfDrums 10 күн бұрын
I remember years ago they offered a conversion kit. I don’t know if they still do. That would be cool.
@MarrowPercussion
@MarrowPercussion Жыл бұрын
Very informative video thank you. Be nice if DW made a direct-drive conversion kit for the 5000 series.
@MJSchoolOfDrums
@MJSchoolOfDrums Жыл бұрын
Right?
@robaay6881
@robaay6881 9 ай бұрын
I work on airplanes. But I’m pretty sure I’ll not get the reassembly right. Maybe I’ll just buy a fresh pedal. Yeah I know. I suck. But that’s what a couple days of overtime are for right? Pu$$$$y or drum pedals. Well done. I have a headache now. Thanks. 😊
@MJSchoolOfDrums
@MJSchoolOfDrums 9 ай бұрын
Yeah this was not easy for me 😆 it’s so important to mark every part as you go or film the process so that you have reference when you forget what you did. 😂
@fontenotjp52
@fontenotjp52 2 жыл бұрын
What size bushing is that at the 11:24 mark? I think that’s the piece I’m missing to put mine back together
@MJSchoolOfDrums
@MJSchoolOfDrums 2 жыл бұрын
I'm pretty sure that's the 3/4 inch bushing
@jorgeivanestradaalapizco4686
@jorgeivanestradaalapizco4686 Жыл бұрын
Did you buy the bearings from DW or are they generic? Are they requested in any specific way?
@theyorkshiredrummer
@theyorkshiredrummer Жыл бұрын
Great video! I’ve noticed there’s 2 different size bearings in the main pedal, 7/8” for the outer two, and 3/4” on the inside. Did you replace all bearings? And if so where did you find them, are they DW replacements?
@MJSchoolOfDrums
@MJSchoolOfDrums Жыл бұрын
Thanks! I didn’t replace them all but I ordered from drum factory direct.
@THEOLYMPIAGUY360
@THEOLYMPIAGUY360 4 ай бұрын
FYI, The “Little Pin” Is called a Retaining Ring. Ring Pilar’s is what there removed with if you have them.
@MJSchoolOfDrums
@MJSchoolOfDrums 4 ай бұрын
Good to know thanks!
@0varz
@0varz 2 жыл бұрын
Thanks for the tear down video! Did you actually replace any bearings? What size are they? They look like skate board bearings. If you didn't replace them what did you do to clean them up?
@MJSchoolOfDrums
@MJSchoolOfDrums 2 жыл бұрын
You’re welcome. Yes I replaced one of the bearings for the primary pedal. I think they are the same size as skateboard bearings but I ordered mine from a drum shop. I used the lubricant to clean the other bearings. Seemed to do the trick.
@petethedrummmer
@petethedrummmer Ай бұрын
The older and possibly current lower line pedals are basically the design from Hoshino TAMA using a skateboard bearing, 608. These are cheap and available, with high end options… The outer beatings for the ‘Delta’ series and current 5000 are BMW R6Z. These of these go for $30 each us in 2024. There are cheaper alternatives and there are faster pedal systems out there, so to me economy bearings are fine.
@MJSchoolOfDrums
@MJSchoolOfDrums Ай бұрын
Thanks for sharing this info. Good to know.
@jorgeivanestradaalapizco4686
@jorgeivanestradaalapizco4686 Жыл бұрын
Did you buy the bearings from DW or are they generic? Are they requested in any specific way?
@MJSchoolOfDrums
@MJSchoolOfDrums Жыл бұрын
I got them from Drum Factory Direct. DW 7/8" Precision Bearing, DWSP213 www.drumfactorydirect.com/
@22Wook
@22Wook 2 жыл бұрын
That “pin” is a circlip. Circlip pliers are pretty cheap and will reduce the chances of breaking the clip or it flying off never to be seen again.
@MJSchoolOfDrums
@MJSchoolOfDrums 2 жыл бұрын
😂 thank you! I figured there is a proper tool for it. I’m lucky it didn’t fly off somewhere.
Which DW Kick Drum Pedal is Right for You?
11:12
Sweetwater
Рет қаралды 161 М.
SKATEBOARD Bearings in a KICK PEDAL?
10:35
Marcus Graham
Рет қаралды 15 М.
Quilt Challenge, No Skills, Just Luck#Funnyfamily #Partygames #Funny
00:32
Family Games Media
Рет қаралды 55 МЛН
It’s all not real
00:15
V.A. show / Магика
Рет қаралды 20 МЛН
Top 3 Double Bass Drumming Mistakes (And How To Fix Them)
11:24
Cameron Fleury
Рет қаралды 10 М.
Speed Star Bearing Install - SS-5000
5:28
Tony Wycoff
Рет қаралды 34 М.
Bass Drum Speed Secrets With El Estepario (Part I)
6:36
Drumeo
Рет қаралды 868 М.
Triple Your Foot Speed On The Drums - Russ Miller
18:38
Drumeo
Рет қаралды 273 М.
How to GREASE, Un-Seize and Clean SEALED Bearings
9:44
sixtyfiveford
Рет қаралды 292 М.
5 steps to perfect kick pedal SPRING TENSION
21:26
Stephen Clark
Рет қаралды 129 М.
Turbo vs Accelerator
6:21
Beu Smith
Рет қаралды 25 М.
Adjust your bass drum pedal for MORE SPEED
21:25
Stephen Clark
Рет қаралды 245 М.
DW 5000 Kick Pedal - Legend Status Unlocked!
12:31
Funky Transmutations
Рет қаралды 10 М.