Am a carpenter myself at Qatar NFE project,I work on this locks mostly... I will be very grateful working with you Daddy
@carliiiartist2 жыл бұрын
Two pliers and thats it! Man you just saved my life!
@nigelmanley1206 Жыл бұрын
A pair of side cutters or lineman pliers work faster in my opinion.
@ellieyu85192 жыл бұрын
The product is similar to our F8000 series, your explaination is very good!
@soloban813 ай бұрын
Thanks man! I was able to fix a loose rim cylinder and save a locksmith call out.
@dab14632 жыл бұрын
Very very good video. You are a professional I would trust.
@padamchand9107 Жыл бұрын
You are so good person so good 👍#udayadewvlog
@johnwuethrich4196 Жыл бұрын
ive got a series 99 panic/crush with a 7500 mortise casset and 996 trim. Does the cylinder just rotate out of the trim after the set screws are losened? It seemed the cylinder was holding the trim on. I dont think I actually have a hole/screw where you did to remove the cylinder.
@drewinstallshardware Жыл бұрын
If everything is lined up correctly on a mortise panic then yes once you loosen the cylinder set screw in the cassette then the cylinder should just spin out.
@RaulRodriguez-fj4mo2 жыл бұрын
Very very good video. can you tell me what model panic device , the model out side handle it is thanks
@62Cristoforo2 жыл бұрын
Well explained and demonstrated. I’m surprised hardly anyone uses hand held screw drivers anymore. I must be getting old 🙄
@padamchand9107 Жыл бұрын
Nice 👍#udayadewvlog
@juanmorse50 Жыл бұрын
Very nice. Thanks for the tutorial.
@padamchand9107 Жыл бұрын
Thanks 🙏 God bless 🙏so good 👍#udayadewvlog
@dankorot74002 жыл бұрын
Awesome video! Keep up the good work
@edwinknabenshue31717 ай бұрын
What if my door has a vertical locking rod and I need to replace the tumbler?
@jesserowe753 жыл бұрын
I have a question about the little metal piece on the back end of the crash bar under the plate on right side when u turn the key it moves the mechanism to allow the door to open it keeps going limp everytime i tighten it down u know an easy fix? Or what do i do in this case?? Please help if u can!! Thank.you
@miaaunderwood2 жыл бұрын
Yuyyu y yuyyyyuyu I u y u u
@62Cristoforo2 жыл бұрын
You’ll need to order a replacement dogging kit. They’re made of plastic or nylon, and tend to wear down over time. A common problem.
@franciscosantos36098 ай бұрын
Wow thanx really straightforward video Thanx
@drewinstallshardware Жыл бұрын
Great video. Thank u!
@peterbraithwaite61984 жыл бұрын
Thanks great video
@Uneke11 ай бұрын
Why not have used a bypass driver? Or broken the pin and unscrewed the cylinder? Drilling is my last resort after I’ve failed picking, bypassing and sheering the pin on the side
@WiliamBennettwildarbennett3 жыл бұрын
Ok have a Q? Is that not a KNOX BOX on the Latch Side of the door. Where's the FD key to that box. Then you have a service key to that door. Because that's a FD CONNECTION & Fire Sprinkler System. Now that you've changed that lock the FD can't get access to the sprinkler system.
@drewinstallshardware Жыл бұрын
Great question. Seems important.
@thangammanikandan70253 жыл бұрын
Thanks good and useful
@dacoldest38963 жыл бұрын
and that job you can charge like 400 dollars lol
@SuperUncleRyan2 жыл бұрын
Attention new guys...be careful using drills or drivers with door hardware. It is very easy to strip or cross thread these screws. I have been doing commercial door hardware for years and I still always use just a screwdriver on most screws especially those in the trim.
@padamchand9107 Жыл бұрын
so good 👍#udayadewvlog
@drewinstallshardware Жыл бұрын
Great advice 😊
@MrVafran124 жыл бұрын
Wooo
@patrykdrozd26375 ай бұрын
Took this guy seriously until I saw the ryobi
@patrykdrozd26375 ай бұрын
Jk thanks for the video
@jonbottoms89885 ай бұрын
I will never understand the use of a panic bar inside a riser room. Ridiculous