How to replace the loadwheels on a manual pallet jack - step-by-step from flipping the jack over, then removal of the wheels to the installation of the new wheels. Find your parts at genericparts.co...
Пікірлер: 67
@adamw4338Ай бұрын
I bought replacement wheels and fixed the jacks at work thanks to this video. No more pulling entire pallets of water with wheels that are falling off and don't roll
@genericpartsАй бұрын
We like hearing that 🙂
@J37152 жыл бұрын
Thanks we still have these crown pallet jacks and they needed wheel replacements. This video helped us out. Thanks a bunch
@chrismusselwhite68294 жыл бұрын
Thank you! Was wondering how the axle was held in place, "pins". Genius!
@No1zHerO6 жыл бұрын
Would pallet jacks last longer if maintenanced every 6 months? I work at a grocery store and jacks to last long ! They are hard to pull or take long going up and down ..? What do you suggest??
@genericparts6 жыл бұрын
A 6-month schedule sounds too rigid. It depends on your wear, roller material, floor, etc. Make sure you have the correct wheels for your application, and keep an eye on the wear. Here is a useful sheet with tips and instructions genericparts.com/assets/GPS_measure-wheels.pdf
@No1zHerO6 жыл бұрын
Thank you so much !!!! I hope to fix all our jacks !!!
@n310ea5 ай бұрын
When you buy new load wheels, do they come with new roll pins and everything as a kit?
@genericparts5 ай бұрын
You can buy the - load wheels only, or the - load wheel kit that comes with all the pins and washer and such, or the - complete wheel kit which comes with load AND steer wheels and all the hardwarre needed (like pins, washers, axles and such)
@xturtlexohx2 жыл бұрын
My work has a few broken pellet jack wheels. I told the management I'll fix it, but they want to pay a professional..... I feel like I'm a professional now after watching this
@genericparts2 жыл бұрын
We make it easy! Please call if you have questions, or need parts. 1-800-331-0839
@jeepsrule684 жыл бұрын
Good video. Told me all I needed to know to replace wheels. Thanks!
@genericparts4 жыл бұрын
Thanks! Keep us in mind when ordering replacement wheels.
@racerchaser272 жыл бұрын
My pallet jack doesnt seem to have pins holding the axle. Do they just beat out with a hammer?
@genericparts2 жыл бұрын
Hi there! Please email directly to CSinfo@genericparts.com so we can answer better, and get more detail.
@deanw70445 жыл бұрын
I have all 4 roll pins our but the axles wont come out. It is a PTH50. is there a different axle on these?
@genericparts5 жыл бұрын
Hi Dean! Axles are likely frozen inside the wheel due to corrosion. See video how to remove rusty axles. kzbin.info/www/bejne/a37XYZttndlpipo The wheel will need to be cut out.
@sebastiandiego59056 ай бұрын
Is this the same process to replace the load wheels for a Crown WP 3000 EPJ?
@genericparts6 ай бұрын
The process is similar, with electric jacks you can not turn them over so the unit must be jacked up and blocked.
@dianarendon28226 ай бұрын
The same, but just different
@sebastiandiego59056 ай бұрын
@@genericparts any chance you guys can make a video? This one was amazing!
@MrsTiffany19827 жыл бұрын
I am looking to replace the load wheels on the pallet jack we have at work. How do I know what size wheels to purchase if I don't have a make or model on my pallet jack?
@genericparts7 жыл бұрын
Just take a picture of the hydraulic unit (side view) and text it to us at 503.523.8990. We'll help you identify your jack, and you go from there.
@shaycameron48796 жыл бұрын
Do you have any recommendations for removing embedded nails from wheels that are in otherwise good shape? Our warehouse has several jacks that I've been working on and I've had some success with a mallet and a small prybar, but it's not easy
@genericparts6 жыл бұрын
Hi Shay! Nails in the wheels are tricky. There is no good way to remove them. If you do, the area where the nail was will start to chip. Might be better off to leave the nails in and plan on replacing the wheel soon. To insure long wheel life, warehouse floors need to be clean. On a side note, our 70D wheels are harder than regular jack wheels and less prone to pick up nails. But again, regular sweeping, if possible, is best maintenance practice in this case.
@valus15853 жыл бұрын
Would some similarly sized screwdriver work instead of the pin punch?
@genericparts3 жыл бұрын
No a screw driver will not work. The proper size pin punch is necessary to remove the spring pin as they are a very tight fit. Most common size needed for manual pallet jacks is 3/16” punch
@S0ulinth3machin310 ай бұрын
you'll mess up the screwdriver
@WHU4485 жыл бұрын
Thank you for such excellent video! (👍🏽👏🏽)
@genericparts5 жыл бұрын
Glad it was useful!
@striderhine Жыл бұрын
what size Pin Puncher is that?
@genericparts Жыл бұрын
It's a 3/16"" inch pinpunch
@hernang75096 жыл бұрын
do u guys knoe whats size for the pin punch to removed tires how many inches ?
@genericparts6 жыл бұрын
A pin punch 3/16 of an inch (or 5mm) will work to take out the roll pin.
@noneovyerbusiness49096 жыл бұрын
Are the load wheels on a later PTH model the same as on a PTH50?
@genericparts6 жыл бұрын
No, they are not. The PTH50 wheels are slightly smaller. Check on our website to make sure you order the correct wheels www.genericparts.com/store/app/Search_Results_PS_ALL.cfm?partSearchSubmit=1&formName2=%23GetFileFromPath%28GetTemplatePath%28%29%29%23&formQuery2=%23CGI.QUERY_STRING%23&partNumber=82283&Submit=Search
@miguelayala10356 жыл бұрын
Okay cool but how do you take off the front ones ...
@genericparts6 жыл бұрын
Hi Miguel, sorry for the delayed reply, i was out of town. Do you mean how to replace the steer wheels? We have a video on those as well: kzbin.info/www/bejne/n5eTfYiehpiGn6c Let me know if you have any more questions.
@bobcat84393 жыл бұрын
Good job
@danwhigham8294 жыл бұрын
The Uline H-1043 does not use a 3/16 pin punch- too big
@genericparts4 жыл бұрын
3/16” Punch is the most widely used. You are correct for model H-1043 please use a 1/8” or 4mm pin punch
@MarioKyriacou1 Жыл бұрын
Thanks!!!
@genericparts Жыл бұрын
You're welcome. Let us know if you need parts
@S0ulinth3machin310 ай бұрын
thank you
@4kgamingerikchannel6615 жыл бұрын
If I work at a grocery store and the manager of the store has the money to fix the pallet jacks but instead pockets the money as bonus for him, where can I call to complain?
@genericparts5 жыл бұрын
sorry, this goes beyond technical questions. Try the store owner?
@genericparts5 жыл бұрын
That's tricky, not really the kind of service we do. Maybe let whoever is the boss - corporate office? - know what's going on. If necessary anonymously.
@chromeforme4 жыл бұрын
File an Informal complaint with OSHA. Try to give as many details as possible. ( pallet number, location, etc ) Do this online. Informal complaint will result in a letter to the owner. A formal complaint will result in a visit.
@luiginoberkel75553 жыл бұрын
Second step should have been; Try to locate your locking pins...
@genericparts3 жыл бұрын
Yes, that helps. You can always check on the line drawing of your jack. You can find it on our website www.genericparts.com/store/Catalog_PDFlist.cfm
@pavel18097 жыл бұрын
very easy awesome
@genericparts7 жыл бұрын
Thanks! Glad to help. Check out our great offer on replacement load wheel kits on our website.
@bobcat84393 жыл бұрын
Can't see
@genericparts3 жыл бұрын
It shouldn't be too complicated, the video will get you going. If you have any further questions, or to order parts, you are welcome to call our customer service at 800-366-5939
@gcorpus55584 ай бұрын
👍🏼👍🏼👍🏼👍🏼👍🏼😊
@irisnoack4 ай бұрын
Thanks😄
@hernang75096 жыл бұрын
Thank u so much.........
@oatmealman47432 жыл бұрын
The axels on this pallet jack do NOT come out that easy...fml
@johnathanbullington97032 жыл бұрын
Yea not that easy on one that gets used 🤣🤷♂️
@genericparts2 жыл бұрын
Yes, depending on the application of the jack, it can be tricky. Let us know if you run into major problems. Our kits come with the hardware for free - in case pins get lost or axles dinked.