I know a much easier way . to change the bulb look under the wheel well towards the front of the car . theres a philips head screw that holds a little plate remove the screw and plate and you can change them in minutes .
@freestyleflowful10 жыл бұрын
cool thanks
@AmoriOvO10 жыл бұрын
You should make a video
@bobb12717 жыл бұрын
Low beam you can go that route,can reach the high beam from there.
@Handd4u3 жыл бұрын
Even going through that wheel well access hole is challenging. You need 2 hands to seat the bulb and then snap it in. Challenging!
@LethargicSquirrel8 жыл бұрын
Thanks for this. As a tall man, I have large hands. Going through the "port" in the wheel well for the passenger-side lamp is a royal pain with large hands. Took me 45 - 60 minutes to replace that one bulb the one time I did it (now I just pay Walmart the $7 to do it). Next time that light goes out (or I get an LED bulb or kit), I'll give this a shot so I don't have to sit at Walmart waiting around. Thanks!
@malittle2508 жыл бұрын
If you go under the tire, there is place labeled "bulb access" and when you remove that you have access to your blub. :)
@Handd4u3 жыл бұрын
That is true. You can get 1 hand in that hole. That makes things very challenging.
@chrisfoley19947 жыл бұрын
Is there anyway you could make a video of how to take apart the actual head lamp to replace?
@PierceMedia9 жыл бұрын
Thank you for the video.
@teddymccall110 жыл бұрын
I'm not a big dude and my hands couldn't fit in there.
@jeffreyalford35487 жыл бұрын
You didn't show anything. You vaguely described how you would do it if you were to do it.
@bobb12717 жыл бұрын
There ISN'T ANY WAY! you got your pork chop hand behind that coolant tank and through those lines. The hose is too short to lift the tank to get your hand in there. I moved the windshield wiper fluid and barely made that to change the high beam! Low beam you can go thru the access panel behind wheel well
@staciivey16163 жыл бұрын
This was one of the best FYI videos I have seen. No small talk just straight to the info that was needed. Now if you could please do another one for the other side. Thanks.
@bigshoww61810 жыл бұрын
You do no the weather guards by by the tire have a access panel to get to the headlight rite? Instead of doing this way, the much harder way
@sashanovozhilov7 жыл бұрын
Thanks for the info! Really helped me to get to that bulb, and eventually it got replaced :)
@jamesmichon1425 Жыл бұрын
Why didn't you use the access panel in the wheel well for the low beam light replacement? It's a single phillips head screw and you have straight on access.
@ronwynn66107 жыл бұрын
Moved the coolant reservoir and now it won't go back in. Any suggestions
@warren80710 жыл бұрын
How did you get your hand in there for the regular bulb after I bolting the tank..? Isn't as easy as it sounds and looks...
@freestyleflowful10 жыл бұрын
for the regular bulb its ok but for the high beam it can be a pain if u got a big hand it took me about 10 minutes.let me know if i can help some how thanks..
@xlr8nvw10 жыл бұрын
Should have read the comments below... After watching the video, I tried to displace the coolant bottle as the video suggests... NO GOOD. After removing the two nuts as suggested in the video, it became clear that the hoses connected to the reservoir would not let it move much... waste of time. I then tried to squeeze my fingers past the rigid brake lines in the fender well... Impossible! I was dumbfounded. I couldn't believe that Ford would do this! It occurred to me that If I could remove the plastic insert inside the fender well, I could probably get at the bulb from below. When shining my droplight into the fender well, I found the panel with the words BULB ACCESS. It has one phillips head screw holding it in place... remove it, and you can reach inside and do what needs to be done... Be warned though... the wires that go to the bulb are very short. I was not able to comfortably pull the socket back through the access hole to pull the old bulb and install the new one. I had to "blindly" put both hands through the hole into the fender and do it by "feel." All is good now... two headlights again! Good luck with yours!
@HarjotJGrewal9 жыл бұрын
There is an access port in the wheel well. You take the tire off and do it through that.
@Handd4u3 жыл бұрын
Don't have to take the tire off. Turn wheel maximum left. Use shorty screwdriver to unscrew access cover in wheel well.
@repairdrive8 жыл бұрын
You da man. Thanks!
@drivers19595 жыл бұрын
waste of time
@mrok89889 жыл бұрын
big help thanks for putting the video down I got a 2006 Ford Fusion have been helping my daughter with and this was very helpful I also done the harmonic balancer water pump and timing you were very helpful today I'm putting her in some fancy high beams appreciate it keep them coming
@artupham43988 жыл бұрын
Thanks! I have an '08 MKZ - this saved me a lot of time replacing the passenger side low beam bulb. The procedure in the manual is way more complicated (put the car on a lift; remove an inner fender panel; and so on). I moved the coolant reservoir and squeezed my hand in to get the bulb - it worked!
@3finger1010 жыл бұрын
Thanks bud, big help...........
@freestyleflowful10 жыл бұрын
of cource thank u for watching
@gainingground68447 жыл бұрын
Good video. It helped me today jus comin back to say thanks.
@mjrton10 жыл бұрын
Thanks you for putting this together
@freestyleflowful10 жыл бұрын
thank u for waching
@robertjohnkline10 жыл бұрын
Thanks for the video - helped immensely for access point to the low beam!
@freestyleflowful10 жыл бұрын
cool great im glad it help
@freestyleflowful10 жыл бұрын
thank yall for wachting and thank u for the comments it helps
@rrohloff9 жыл бұрын
Don't know if someone said this, but there's actually a panel underneath the wheel well. Just remove that, one screw
@nato83659 жыл бұрын
Ryan R yes there is which makes t is video worthless
@freestyleflowful9 жыл бұрын
thank u for letting me know
@denibelarasaldana97609 жыл бұрын
Is a hole by the tired that let u change the light I shouldn't watch this video just make my life harder