Replacing a graphic on the Budget Roller Banner stand

Рет қаралды 170,769

6 жыл бұрын

How to replace a graphic on the budget roller banner stand.
Stand and replacement graphics available at www.printdesigns.com

Пікірлер: 37

@chukanwosu7478 9 ай бұрын

This is simply explained and well understood. Thank you. This is of great assistance.

@achotshering4614 Жыл бұрын

That was simple and great information I needed!! Thank you! 👍

@tkbradford1247 2 жыл бұрын

Thank you. This was perfect information. I am above average handy, so I shouldn’t have any problems with this. I just wasn’t sure how it would attach on the bottom, and your video explained it in great detail.

@PrintdesignsLTD 2 жыл бұрын

No problem, i'm glad the video was useful. You will need to use a strong double sided tape to attach the print. After sticking the print to the stand you can over-tape the join between the graphic and the stand with parcel tape. This will make the join more secure!

@danielwalker4625 4 жыл бұрын

I like this edit!!

@anantasakrattanasopa1979 4 ай бұрын

Great job!! Thank you very much.

@marcosfurukawa1104 Ай бұрын

!1. Excelente vídeo! Muito bem explicado e informativo.

@jeromeclausdritchz3595 3 жыл бұрын

THANK YOU

@IanRuben 3 жыл бұрын

what happens if the pin was pulled out prematurely and all the spring got inside of the bottom part is there a way to repair this issue? thank you

@MarkThompsonUK 3 жыл бұрын

If you pulled the pin prior to attaching the print (with the top rail in place) then the spring inside will lose tension. It can be fixed but it is fiddly. Attach the print with the top rail on, then remove the screws that hold the end plate on the stand. Do this on the side of the banner that has the flat part of the spindle protruding from it, not the other side that has a round spindle protruding from it. With the screws undone, turn the end plate round and round whilst keeping the flat part of the spindle in the slot on the side of the banner casing. This is tricky! After about 20-25 turns the print should be wound inside. Now put the screws back in.

@MS-uz4ix Жыл бұрын

Accidentally pulled the pin and the spring on the roller unwound. Any tips on rewinding the roller to get back to the original tension?

@PrintdesignsLTD Жыл бұрын

Whoops! sorry to hear about this. The banner can be fixed but it's a fiddly process. The first thing you need to do it remove the screws from the end plate of the stand that has the flat spindle protruding from it. With the screws removed you can rotate the end plate of the stand clockwise while it is held flush to the casing of the stand. The flat head of the spindle should be still poking through the slot when you rotate the end plate. Be careful here because as you rotate the end plate with the spindle poking through the slot, the tension on the spring increases inside the stand. It is easy to accidentally pull the end plate away whereby the spindle will pop out of the slot and 'lose' all of the tension. Also be very careful that the end plate does not fly out of your hands whilst turning it or you could hurt yourself! We wear gloves and safety goggles when doing this. You need to give this end plate about 20-25 turns after which the print should be wound back into the stand. Once the print is wound in, put the screws back onto the end plate to secure it. Again, be careful that you don't pull the end plate away from the stand and allow the spindle to pop out of it's slot while doing this or you will need to start over! I hope this helps and good luck.

@MS-uz4ix Жыл бұрын

Thank you!

@justrightinvites5619 10 ай бұрын

thank you

@mattjarrels4594 Жыл бұрын

Thanks for the info! This helped me out at work

@PrintdesignsLTD Жыл бұрын

No worries Matt, glad the video was useful! Best wishes www.pintdesigns.com

@Ayzprella 7 ай бұрын

thank you for your video

@PrintdesignsLTD 7 ай бұрын

No worries, I'm glad it was useful to you. All the best www.printdesigns.com

@deydagaraycoa5499 Жыл бұрын

do you know what can I use if the locking pin is missing?

@PrintdesignsLTD Жыл бұрын

You could use a small nail, a matchstick or cocktail stick or a small allen/hex key

@tedfrazier9586 8 ай бұрын

Thank you

@PrintdesignsLTD 8 ай бұрын

No worries at all. Glad the video was useful. Best wishes www.printdesigns.com

@timtuff1011 3 жыл бұрын

I have a banner like this that was installed backwards - the print side faces the pole. Can I unscrew the side panels and reverse the roll entirely? Or do I need to return to the banner company?

@PrintdesignsLTD 3 жыл бұрын

Hi Tim, the print would need to be removed and refitted in this case. You should contact the company who you ordered it from and ask them to collect the banner and replace it!

@kerryoreilly9308 2 жыл бұрын

Thank you. This fix worked!

@MichelL-lv4fp Жыл бұрын

What kind of tape should I use?

@PrintdesignsLTD Жыл бұрын

Hi, you should use a good quality permanent adhesive tape. We use 50mm tesa 4965. It works well for us based on the printing materials we apply to roller banner stands at www.printdesigns.com but you should test adhesion to the particular print material you are using to make sure it holds OK!

@abdelkebirtaghia3690 3 ай бұрын

شكرا جزيلا

@dps253 2 жыл бұрын

Where do I get the pin?

@ajlavilla Жыл бұрын

I think it comes with the stand

@PrintdesignsLTD Жыл бұрын

When we send out replacement graphics for roller banner stands, we normally supply a locking pin. It's worth noting that if you don't have a specific locking pin, you can use something similar instead. A small nail or hex key should do the job!