Excellent video. I own an 307 and you video help me a lot to remove oil pan. Thank you.
@isitfixedyet8916 жыл бұрын
Hi Carlos, Thanks a lot for your feedback! I appreciate it a lot. Cheers
@davem9204 Жыл бұрын
Thanks for the guide here. I'm in the middle of the same job on a Citroen C4 which has the same engine. Like yours, the sump plug in the Citroen was crossed threaded by someone, so just replacing the sump.
@richardwallinger16833 жыл бұрын
Hi great video . hopefully the 1.4 HDI is the same .there is a small oil leak which hopefully is only the sump pan seal. I reseal cat flanges using wood burning stove high temperature 1400 C sealant . I have just replaced the front suspension lower control arm bushes and also the rear axle beam pivot bushes in situ .I copied the screw jack tool a guy made on You Tube .
@presidentticode63402 жыл бұрын
Hello, I have a Peugeot 307 like this one. The first and second oxygen sensors always fail. I had to change them and then they broke again. Do you know what is the reason?
@debelguzi6 жыл бұрын
Thank you very much, I needed that my oil Pan leaked. Like the usually excellent video,this is the second time that your video helps me thank you again.
@isitfixedyet8916 жыл бұрын
Hi Sasa, I really appreciate your feedback. It is good to know that this work is needed :) Cheers
@grzegorzkolbrecki83444 жыл бұрын
Be happy to have alternate oil pan. Or maybe that's diference betwen ph1 and ph2 models. I have 2002 model and struggle with the one, with rubber seal, this one is much closer to right drive axle bearing support so it was very hard to maneuver betwen this support and oil pump to take oilpan out and impossible to manover it back without damaging seal by guideing pins/bolts. Oil pan not comes out stright down and back up but with the strange angles. So what left in this case? Removing this support was nesessery, to do that i had to remove driveaxle too. So much work for stupid oil pan seal :/ Now I have to detach central bearing from that support, it's unscrewed but it stuck, i'm afraid that without using force it would not come out. And i've not planned to replace that bearing. Stupid project...
I havent a 307 BUT thanks a lot Sir......................love ya style
@ryadhkebaili19006 жыл бұрын
Thank you for this userfull video
@isitfixedyet8916 жыл бұрын
You are very welcome Ryadh :)
@GTA-wy2gp4 жыл бұрын
Hello! Do your videos have russian or Ukrainian languages? Thank you, good videos!
@johnson36herbalife2 жыл бұрын
which size is alan key from flywheel side,last one taken out?
@2giggz5 жыл бұрын
Thanks my dear, i feel i can do anything with my 307 style
@jared46708 ай бұрын
Anyone know the part number for the protective beam @ 7:32? Previous owners removed it and didn't put it back. I would like to get another one.
@chrupek84826 жыл бұрын
Great job:)
@isitfixedyet8916 жыл бұрын
Thanks! :)
@عليسليم-ل1ع2 жыл бұрын
Hi my friend 👋 I hope you can help me 🌹 my car peugeot 307 2006 I have a problem in the power steering. * The power steerin Sometimes does not working, But when I turn off The engine and start the engine again the power steering starts works normally, sometimes Two or three days pass without any problem The power steering . 💁🏻♂️ And sometimes power steering stops working more then 5 times a day 🤷🏻♂️ I already replaced the power steering in a new one, put it still the same problem 🤦🏻♂️ * I think the problem is overhead . I believe that the the power steering temperature goes higher and power steering stops itself 🤔 what do you think? *P.S : wen I cool down the power steering in water hose hes starts works normally 😐 *P.S 2 : wen The Power steering works the steering wheel is very very easy to Spin and light and fast. Thank you for reading my problem and excuse me for explaining a lot 🌹
@asifhussain40715 жыл бұрын
Hi there I have a problem with my car the oil is leaking from top of the exhaust can you help me?
@MrJolly-lb9je Жыл бұрын
When sealing aluminium to aluminum - use sealant . When sealing aluminium to steel/cast iron - use gasket (preferably gasket only , dry fit , without added sealant) .
@niquedegraaff6 ай бұрын
there are no gaskets for this part of the vehicle. You have no choice but to use fluid silicone sealant.
@jatinderkumar15925 жыл бұрын
hello sir i have peugeot 307 hdi 2.0 90 hp have problem all dashboard signs are off and the car not starting but taking self
@blackfrog61535 жыл бұрын
спасибо!
@isitfixedyet8915 жыл бұрын
Пожалуйста! :)
@tobiaszkomorski59805 жыл бұрын
Okay. I unscrewed all the screws. that's exactly what I have for these 22 pieces. oil pan I do not want to disassemble. can you help me somehow? mass any way for such a problem?
@annamanna22954 жыл бұрын
Somebody used sealing glue instead of silicone? Hit the pan around with a rubber hammer.
@tobiaszkomorski59804 жыл бұрын
@@annamanna2295 yea i tried as strong i could. It hasnt worked. Samebody have used a silikone glue or something. But thanks for help. 😉
@rafaelcaliforniaquiroz78735 жыл бұрын
Thanks brother.
@sergpinto15 жыл бұрын
Good job :)
@mahmoudshahin92956 жыл бұрын
I have a Peugeot 307 diesel 2.0 some times and I drive on a road and go over another car do not respond and then suddenly speed up. And when I stand on the traffic light when I want to drive it also does not respond then suddenly a good acceleration
@isitfixedyet8916 жыл бұрын
Hi Mahmoud, Have you tried to read errors through PP2000? Cheers
@mahmoudshahin92956 жыл бұрын
Yes No Error
@mahmoudshahin92956 жыл бұрын
Please help
@mahmoudshahin92956 жыл бұрын
؟
@axnn14 жыл бұрын
Mahmoud Shahin Get your OBD checked by a TRUSTED shop or mechanic only. They will read data about your car where you can find and resolve the issue. Be cautious as many shops say you need to fix things which don’t need fixing.