Restoration - Circular saw shaft

I found this circular saw shaft a few years ago in the junkyard and I knew that one day I would need it. Finally came the day when the shaft looks nice and is restored.
The most important thing was replacing the bearings because they were very worn and noisy. The rest is cleaning and painting :)

[@williamoverton7265]

Very nice work. 😍

[@malcolmporter4771]

Made in Poland with a Route 66 sign on the wall. Awesome bro.

[@georgemckenzie6552]

Good job

[@modarghabra6804]

you clearly done alot things other than fhe videos in your channel. great job watched them all

[@-Deena.]

Just found your channel and subscribed. Really enjoying your uploads. Thank you! 🧡

[@sencormagyarorszag-fanclub4871]

That blue is so cool!

[@10Mbowman]

metallic blue i think

[@КошмарКошмар-й2б]

Hi bro 👋👋👋 very good restoration circular saw shaft 👍👍👍💣👌🏽

[@seansysig]

Nice resurrection. I want one.

[@rodlewis4047]

I’m surprised that you didn’t smooth out the welds!

[@andrzej3511]

The welds are hideous indeed. Maybe it wasn't worth introducing some new thermal stresses? Or maybe some housing will be used eventually? We will see in the episode about the table saw.

[@WorkshopFromScratch]

very good restoration :)

[@RickSA08]

Great restoration!! The saw came out really well! Could you possibly tell me what the bearing part numbers are? 👍

[@anthonywall5227]

Thank you

[@lordginger636]

So I came from made in Poland's channel and now I'm wondering if you are the guy in the vids that always helps him lift heavy stuff off the table and other stuff.

[@rataj72]

Ta tarcza to tylko testowo czy docelowa? sam niedawno nabyłem podobny wałek, będzie do tokarki do drewna ;)

[@victoryfirst2878]

The pulley that you put on the shaft has a good bit of run-out.Probably due to a jamming in the history of this shaft housing life. That makes the shaft vibrate and make noise when in use. Just saying Bring me back to life - Restorations.

[@JankoWalski-uo2br]

Dlaczego nie poprawiłeś tych paskudnych spoin po spawaniu ? Pozostał mi taki mały niesmak całości .

[@markomilosevic3376]

Doesn't this nut on axle supposed to be left thread so it doesn't get lose during cutting??

[@waynep343]

i bet that at sometime in the past. somebody greased it without wiping the end off the grease gun or the grease fitting and filled the housing with dirt in the grease.. contaminating the bearings. depending on how tight the bearings fit in the housing.. you pressed them in wrong. you should have filed or stoned the marks on the shaft down.. that can effect bearing life... when you pressed the bearing on the shaft.. you should have used a collar that pushed only on the inner race.. then when you pressed the single bearing on the shaft in.. you should have used a press tool that only pressed on the outer race.. then when you turned it over.. you have an issue.. you must push the entire side of the bearing into the housing and onto the shaft.. but both of those have to be supported at the same time. you could have used a collar on the already pressed in bearing that covered both the inside race and outside race.. while pressing the last bearing in using a similar tool that pressed on the inner and outer race at the same time.. this complex procedure would have gotten the bearings installed without destroying the smooth balls and ground races with excessive side loading while you pressed them in.. even putting the double groove pulley on should have had the assembly standing on the shaft while tapping the pulley on. i realize this is just a video.. but doing it right really improves the bearing life.. hopefully there was some kind of dust seal in the outer gland nuts..

[@michaelslivensky8741]

Please post a link to your video showing how you did it. Thanks.

[@ionstorm66]

Those marks are more than likely from the last repair. Very common hack to get bearings to fit on worn out shafts after a bearing spun on it. A few peens will allow the bearing to fit.

[@crlist1453]

do you know where I can find a new bearing shaft assembly like this?

[@kubajeziorski3637]

Panowie Czy oś wałka ma 25mm? bo na 25,4 chyba nie występuje... Pozdrawiam Kuba

[@tectalabyss]

Great job ! I liked and Shared. All my best.

[@stanislawmotyka3623]

Jak bym chciał u ciebie zamówić taka maszynę do cięcia to czy byś był zainteresowany i za ile.

[@maksonhildete]

You should have removed the bearing dust from the inside to make contact with the grease!

[@wildrooster1215]

made in poland bring me here

[@jeremyarnold1979]

Looks like a Jack shaft off of a murrays go kart, lol

[@aleksnec8994]

Why did you put seeld bearings? Have are you going to grees them?You schud open inner side !

[@aleksnec8994]

Every thing else is perfekt like alweys!

[@peterjames4435]

I agree they should have been open both sides . Now they can’t be greased and worse still the outer bushes will be starved of lubrication, if not remedied it would have lasted longer left untouched. That’s my opinion. Otherwise it looks good

[@01keram]

Jakiej średnicy jest ten wałek?

[@blakkkatt9]

What did the shaft come off of...would like to fine one...

[@markuspihlajaniemi3711]

What is blade diameter and model?

[@anthonynyman167]

Nice work! Soo.... Is there a video coming with the saw in use?

[@anthonynyman167]

@Simon Sinowetz Thanks! Just watched it over breakfast. That's a lot of fabrication. I was expecting some kind of sawmill for wood.

[@balakumaran599]

Bearing size details pls

[@bigmacintoshishe]

На корпусе же есть отверстие под маслёнку, зачем ставить закрытые подшипники в таком случае?

[@stell33.stell33]

Смазка злотых кучку стоит.

[@_aux7816]

portrait

[@HarryHov]

Parts washer next???

[@bigmacintoshishe]

обожаю Hammerite.

[@thabaldwookiee1692]

Please tell me what kind of paint that is

[@aviohebshalom3392]

It's called hammer tone paint. The best brand is called hammerite. And it comes in a bunch of colors.

[@thabaldwookiee1692]

@@aviohebshalom3392 Thanks man as always great work

[@aviohebshalom3392]

@@thabaldwookiee1692 I'm not the guy who made the video, I'm just helping to answer your question. Since he didn't reply to you, I figured that I would.

[@thabaldwookiee1692]

@@aviohebshalom3392 🤣🤣😂😂 Well thanks anyway

[@aviohebshalom3392]

@@thabaldwookiee1692 No problemo just doing my part.😜😜😜😖😖😖

[@amyasseektruth8246]

Made in Poland

[@joegilly1523]

Nope ,had a table saw bearing go bad when I was ripping oak . It shot the wood back into me and broke my pelvic bone . The bevel plate then shot over my head and hit a wall 20’ behind me. Got laid off my first day back to work,3 months later. Come to find out two more guys got hurt before that A hole replaced that 5 hp table saw. I still hate table saws .💀💀💀💀💀

[@bringmebacktolife-restorat5698]

Actually, it will be used for chop saw so it should be relative safe :)

[@joseelias9475]

V

[@joseelias9475]

V