REVERSE DIAL INDICATING ALIGNMENT|CROSS DIAL POSITION|FORMULA METHOD VS GRAPHICAL METHOD

TOPICS EXPLAINED:
REVERSE DIAL INDICATING ALIGNMENT FORMULA AND GRAPHICAL METHOD COMPLETE PROCEDURE AND DEMONSTRATION WITH EXAMPLE READINGS.
PRE-ALIGNMENT PROCEDURES
BAR SAG
SOFT FOOT
CROSS DIAL POSITION FORMULA METHOD
VERTICAL MISALIGNMENT
HORIZONTAL MISALIGNMENT
CROSS DIAL POSITION GRAPHICAL METHOD
VERTICAL MISALIGNMENT
HORIZONTAL MISALIGNMENT
PARALLEL MISALIGNMENT
ANGULAR MISALIGNMENT
ALIGNMENT CALCULATION
ALIGNMENT GRAPH.
SUBSCRIBE FOR MORE ROTATING AND STATIC EQUIPMENT VIDEOS.
/ @rasetech
RIM AND FACE ALIGNMENT FORMULA METHOD | ENGLISH
• RIM AND FACE ALIGNMENT...
HOW TO FIX SOFT FOOT ON SHAFT ALIGNMENT | ENGLISH
• HOW TO FIX SOFT FOOT O...
HOW TO FIX SHAFT ALIGNMENT SOFT FOOT
• HOW TO FIX SHAFT ALIGN...
BAR SAG | ALIGNMENT
• BAR SAG | ROD SAG | S...
RIM AND FACE ALIGNMENT FORMULA METHOD
• RIM AND FACE ALIGNMENT...
RIM AND DOUBLE FACE DIAL ALIGNMENT FORMULA METHOD
• RIM AND DOUBLE FACE DI...
BELT DRIVE PULLEY ALIGNMENT STRAIGHT EDGE METHOD
• BELT DRIVE PULLEY ALIG...
RIM AND FACE DIAL ALIGNMENT TOOLKIT FOR METAFLEX COUPLING
• RIM AND FACE DIAL ALIG...
CENTRIFUGAL COMPRSSOR DRY GAS SEAL SUPPLY SYSTEM
• CENTRIFUGAL COMPRESSOR...
RECIPROCATING COMPRESSOR PISTON OVERHAULING PROCEDURE
• RECIPROCATING COMPRESS...
CENTRIFUGAL MULTISTAGE PUMP ROTOR IMPELLER ARRANGEMENT
• CENTRIFUGAL MULTISTAGE...
HEATLESS DESICCANT AIR DRYER AND OPERATING TIME SEQUENCES
• HEATLESS DESICCANT AIR...
STUFFING BOX SQUARENESS|BORE CONCENTRICITY|SHAFT RUN OUT
• STUFFING BOX SQUARENES...
HOW TO SELECT SPANNER SIZE FOR BOLTS AND NUTS | INCHES TO MM | MM TO INCHES
• HOW TO SELECT SPANNER ...
DUPLEX BEARING ARRANGEMENT IN SINGLE ROW ANGULAR CONTACT BALL BEARING
• DUPLEX BEARING ARRANGE...
#reversedialindicatingalignmentmethod #rotatingandstaticequipments #graphicalandformulamethod

[@johnbosco9577]

Excellent explanation

[@gktilesceramics6613]

அருமையான விளக்கம் நண்பா...நன்றி

[@rajkumar-ck6mh]

Thanks for this knowledge

[@rasetech]

thank you sir...

[@asadraza1755]

Excellent sir

[@rasetech]

Thank u sir

[@rubenchok9692]

very good ... thanks from bolivia

[@rasetech]

Thank you bro

[@pulikarunakar7127]

Thank bro nice video

[@rasetech]

Welcome bro...

[@morabveill8075]

Thank you my brother

[@rasetech]

Morab Veill welcome bro

[@mukeshkumar-ni6wx]

sir in which (rim and face or reavers) we get accurate alinment with accuracy

[@shahidmehmood6981]

Thank you very much for your support 🙏

[@ashokmurali5080]

Supper sir

[@rasetech]

thank you sir

[@Apriest99]

Sir in your rim and face alignment video you have explained that in vertical alignment if front foot or rear foot value is +ve then we need to remove the shim and in horizontal alignment if the value is -ve then the motor has to be shifted from left to right but here in this video both is opposite why?? Rupert Rodrigues sir pls comment on this🙏

[@rasetech]

Dear Sir, Please dont compare rim and face and reverse. lot of differences will be there. for rim and face there is theoretical formula and for reverse dial alignment there is theoretical formal. please dont Confuse and collapse. Thanks for your comment.

[@gabrielprisly6883]

Bro Please provide procedure and tolerance for hot and cold allignment

[@venugopalnair3743]

👍

[@THE_MC707]

Hey brother thanks for sharing this video, but I'm confused, what is the difference between *coupling* *distance* and *D1* ?

[@rasetech]

D1 means distance between the 2 dial indicators(stationary machine dial and movable machine dial) plunger center. DBSE means Distance between shaft ends.

[@rodriguesrupert]

Rupert Rodrigues 1 second ago Watch these videos maybe they will help 1) kzbin.info/www/bejne/mmizpGCtqrGdnaM (TES Engg school method no-1), 2) kzbin.info/www/bejne/fWjNdaiNnrV1eKs (TES Engg school method no-2), 3) kzbin.info/www/bejne/l2KToGeOlryljtk (TES Engg school method no 1) ,4) kzbin.info/www/bejne/jJDQf4Obfr2ei8k (TES Engg school method no 2). The first two videos are rim-face methods and the other two are the reverse (cross dial) method.

[@prabhuvelprabhu6747]

Sir sm machine side rottaite pannamudiyatha mudiyathu , ithuku oru vedios podunga sir . Cupling gap ten mm sir. Vedios podunga sir

[@rasetech]

Ok sir thank you ❤

[@mukeshkumar-ni6wx]

Dear sir,according to your all alinment video we find that olny in single face dile (rim$face) alinment formula method when calculation came (--) than add shim,and when calculation came(+) than remove shim But after in your all alinment video that is * double face dile (rim$ face) alinment * and both revers dile alinment When calculation came in (+) than add shim,when calculation came in (--) than remove shim. according to you ,am i understand ........

[@rasetech]

mukesh kumar ok thank you thanks for your comment.

[@rodriguesrupert]

watch these videos maybe they will help 1) kzbin.info/www/bejne/mmizpGCtqrGdnaM (TES Engg school method no-1), 2) kzbin.info/www/bejne/fWjNdaiNnrV1eKs (TES Engg school method no-2), 3) kzbin.info/www/bejne/l2KToGeOlryljtk (TES Engg school method no 1) ,4) kzbin.info/www/bejne/jJDQf4Obfr2ei8k (TES Engg school method no 2). The first two videos are rim-face methods and the other two are the reverse (cross dial) method.

[@donignasis8355]

Sir, we are no using coupling distance 190 mm

[@mishrasanjaykumar6144]

Please sir make a vidioe on reaverse alighnment method formula from 0 leval to 100 leval in hindi

[@manibigdurai1850]

My friend for Horizontal alignment correction as per shown your dial value , need to move motor left to right

[@rasetech]

thanks for you comment.

[@rodriguesrupert]

You have to be standing facing the stationary machine from the motor side as he has shown. If the points in the graph are above the centerline then we have to move from R to L, if below the centerline the L to R.

[@donignasis8355]

You standing wrong side, go to opposite

[@premkumarpearlcity]

Sir kindly formula use panama dial indicator parthu epdi shim correction pandrathunu oru practical video post panunga (reverse dial indicator)

[@rasetech]

Ok sure...

[@mohamedsaleem2646]

Dharma prabu.... neenga ingayum vanthuttingala... 😁😁

[@kondayyanaiduaaa]

Hello sir this kondyya naidu yallapu sir I tried to change the sm and mm readings as .+35 and ._35 same formula I was used but not matching the Graff readings

[@rasetech]

Please check the calculations and measurements again.

[@kondayyanaiduaaa]

I check but not match the calculation and Graff

[@kondayyanaiduaaa]

Can you send your WhatsApp no

[@kondayyanaiduaaa]

I am wating for your valuable solution

[@rasetech]

@@kondayyanaiduaaa dear sir plesse check with different sm and mm instead of same value. I think it should not be same.

[@rodriguesrupert]

According to your figure shown SM dial is above so the dial will go inward so it will show a positive sag reading and the MM dial is below so it will go outward so it will so show a negative sag reading. Your readings in the calculation show the opposite which confuses everyone. I referred to dial movement videos just to be sure. See the video at 24:00.

[@rasetech]

Thanks for your comment❤

[@mukeshkumar-ni6wx]

Dear sir, in rim and face alinment we eaisly know that when we use ffv or bfv farmula according to dile gage plunger presser on FACE,but in revers alinment how we know when we use ffv or bfv farmula,

[@rasetech]

I cant understand your question. Kindly repeat again.

[@premkumarpearlcity]

Same doubt for me also Rim nd face method la dial parthu angular misalignment crct panirlam but reverse la formula graph use panama dial indicator parthu epdi correction pandrathu?

[@rasetech]

@@premkumarpearlcity ok understand.

[@rasetech]

@@premkumarpearlcity i will post a video for this question. Kindly stay tuned.

[@premkumarpearlcity]

Waiting for your video bro Kindly post as soon as possible May i know your contact number?

[@minhaayaan3794]

Please rply bro reverse allingnment clock ways and anti clock ways how

[@rasetech]

Minha Ayaan you can do both clock and anticlock wise sir

[@minhaayaan3794]

@@rasetech please up loading master level aligning

[@rasetech]

@@minhaayaan3794 ok bro

[@minhaayaan3794]

@@rasetech thanks annai

[@srntechnicianskill3743]

Sir please speak Hindi

[@shaikhbaji9957]

you did before one video that one only u explained graphical method right but, that video regarding u had not make half the total indicator reading, y u was explained different .

[@rasetech]

Thanks for your comment. Kindly verify the two methods. Actually both are same.

[@SenthilKumar-eg4if]

Do you have a graphic sheet app for alignment?

[@rasetech]

I dont have bro

[@jameelahmad4778]

Sir very important but Hindi dawnlode

[@premkumarpearlcity]

Moreover in graphical method sm + and - ok but mm - and + nu thana varanum since it's a reverse dial method

[@rasetech]

Dear prem see this video also for your clarification.

[@rasetech]

kzbin.info/www/bejne/pHSwkIycZbpmp6M&app=desktop

[@premkumarpearlcity]

Can i have your contact number sir for more clarification?

[@rasetech]

@@premkumarpearlcity send your mobile number by mail

[@premkumarpearlcity]

@@rasetech what's your mail id bro

[@MCSagadevan]

Sir how do you arrive bar sag value there is no clarity kindly deliver

[@rasetech]

see this video for bar sag. kzbin.info/www/bejne/eJvEfIp_j72JjbM

[@rodriguesrupert]

watch these videos 1. kzbin.info/www/bejne/d5-xl6WNbKqkec0 Controlling Backlash 2. kzbin.info/www/bejne/bqKqY3aNrtSql7M Correcting for Rod Sag

[@karthickpandi.r5675]

hi sir last video if answer is plus shim is remove .answer is - add shim but now u saying answer plus add shim

[@rasetech]

That is rim and face and this is reverse dial sir. Dont collapse and compare those procedures.

[@mukeshkumar-ni6wx]

sir face to face alinment method video banao please

[@rasetech]

I will try sir.

[@nirmalsurendranmenon7049]

What are the tolerance for TIR

[@rasetech]

Its is depends speed and size and Manufacturer recommendations. but overall thumb rule is 0.05 mm TIR.

[@rohitpaswan277]

Sir please es method ko hindi me samjhayen

[@nirmalsurendranmenon7049]

How did you get bar sag values?

[@rasetech]

kzbin.info/www/bejne/eJvEfIp_j72JjbM

[@nirmalsurendranmenon7049]

@@rasetech I saw the video. So why the sag value is the reading taken from 6 to 12 and not 12 to 6 ?

[@mahakalkediwane9623]

Sir hindi or english please so we can also undrstand

[@bijaykumarmohanta3522]

Plz make it in hindi

[@sarojkumarroutray2895]

Shaft runout reading so

[@kalai656]

Vanakam anna Moththam ethana method irukku shaft allignment la 1.laser allignment 2.rim and face method 3.reversed direction method 4.radial and angular allignment (ithuvum rim and faceum sameaaa)

[@rasetech]

Radial,angular and rim and face ellam onnu thanga bro

[@kalai656]

@@rasetech Vera ethum methods irukaaa

[@kalai656]

@@rasetech and can i align rim and faceethid without formula?..

[@rasetech]

@@kalai656 rim and double axial alignment irukunga

[@rasetech]

@@kalai656 yes, pratically you can by experience.

[@ramueppili5223]

Sir Please expain dialgauze allignment practically

[@rasetech]

Dear Sir, Practically I cant able to make videos because Mobile and camera is strictly prohibited inside of plant.

[@shahidmehmood6981]

Sir can I get RIM & FACE graph alignment horizontal and vertical

[@rasetech]

Sure I will try to make it for you... but it will take sometimes. Thanks for you comment...

[@SUNILKUMAR-lr3ru]

Sir G please Hindi longage me video banaeye please sir

[@rasetech]

Noted with thanks❤

[@rasetech]

Dear Friends, Recently I have uploaded the English version of this video on our channel. Kindly please check it out. Many thanks for your support. kzbin.info/www/bejne/rZ-mYqCNobdme5o

[@satishsh309]

Bro can you explain in inches pls

[@rasetech]

There is no major difference between mm and inches. Only the units bro

[@rodriguesrupert]

Rupert Rodrigues 1 second ago watch these videos maybe they will help 1) kzbin.info/www/bejne/mmizpGCtqrGdnaM (TES Engg school method no-1), 2) kzbin.info/www/bejne/fWjNdaiNnrV1eKs (TES Engg school method no-2), 3) kzbin.info/www/bejne/l2KToGeOlryljtk (TES Engg school method no 1) ,4) kzbin.info/www/bejne/jJDQf4Obfr2ei8k (TES Engg school method no 2). The first two videos are rim-face methods and the other two are the reverse (cross dial) method.

[@rasetech]

@@rodriguesrupert thanks for your comment...

[@rasetech]

Dear Friends, Recently I have uploaded the Hindi version of this video on our channel. Kindly please check it out. Many thanks for your support. kzbin.info/www/bejne/fJzdZGx6ismmm7c

[@ramkumar2584]

Please hindi me boliye ga sir

[@naeemrajput00]

Sir please conversation hindi

[@vinitsingh116]

I need Hindi language videos

[@rasetech]

Received with thanks

[@liyakattiliyawala]

Please explain in English or hindi

[@rasetech]

Ok sir

[@rajkumarchauhan8612]

Make in hindi sir

[@rasetech]

Received with thanks

[@jameelahmad4778]

Sir conversation in hindi

[@erikbeybutov5230]

I watched a little and tried to understand but didnot understand anything what you are telling there🤨

[@kalai656]

Bro ?...

[@rasetech]

Hi bro unga whatsapp number kudunga. I will explain.

[@josephregner7697]

Used international language you post utube

[@mdasifiqbalkhan7796]

Its better to explain in English

[@SANTOSHKUMAR-vf7uz]

Please speak Hindi