RICOH AFicio MP2001 MP2501 Replacement Drum Claeaning Blade Charge roller developer

RICOH Aficio MP2001 MP2001L MP2001SP MP2501L MP2501SP how to replace drum developer blade and cleaning roller replacing replacement
🔥🔥 KZbin SUPPORT: / @mrricoh
😁😆 PATREON: / copyexpertmoviestudio
🔥💥 PATRONITE: www.patronite....
📽Camera: CANON EOS250D
🎬 Plan lighting: Sachtler Reporter 200D
🎤 Microphone: Trust GXT 252 + Emita Plus Steraming
💻 Movie editing program: WonderShare Filmora
Copier parts www.copy-expert...
Facebook: / copy-expert-1134316788...
Used copier parts www.copy-expert...

[@dahmanus2002]

in the minute 4:26 i advise you to align the development gear holes to the up position, you should be able to note them, and this is the purpus of manufacturing them with the small hole in only one side,believe me try it.

[@MrRicoh]

Thank you, you're right

[@MrRicoh]

Insert a small flat screwdriver between the plastic housing and the screw and at the same time remove the screw with a Phillips screwdriver.

[@FrogSchoolDotEu]

On a 2501 newly refurbished PCU is printing lines and the drum cleaning blade is not cleaning the drum, what can be the cause of that ? Before use I did a TD initialize and a developer mixing.

[@MrRicoh]

What did he lubricate the Drum Cleaning Blade with?

[@engelsdr]

Gracias

[@MrRicoh]

Greetings from Poland in Europe.

[@stephensharma3259]

I bough ricoh developer drum unit complete. but had to refill the developer powder inside. Printing test page shows many uneven and mixed marks. And the original drum developer unit has jst thin lines but evenly distributed printing on other places. Why is this new one worse than the one that came with machine?

[@MrRicoh]

the MP2001 2501 models are very sensitive to dirt. perform complete printer maintenance and the problem will be solved immediately

[@Umadevionlineservice]

in the minute 6:19 that screw is jamed how to change the cleaning blade sir

[@MrRicoh]

Pry the screw with a small flat-head screwdriver and remove it at the same time. it has to work out

[@radhakrishnastationery1296]

i have ricoh mp2001l machine, when i print a copy , my top side of the paper is very light , or sometime not clear, and other bottom part is ok...vcan u tell me what is the exact probvlem sir ?

[@MrRicoh]

This is a very simple fault. My guess is that the copier has not been maintained for a long time. So open the front door and unscrew the gray cover and remove it. There is a small laser glass in the middle - remove it and clean it. The problem will pass. But if the problem continues, it is possible that the machine has already made 60,000 copies and you need to replace OPC DRUM, BLADE, DEVELOPER and CHARGE ROLLER.

[@radhakrishnastationery1296]

@@MrRicoh THANK U SIR , LET ME CHECK TODAY , machine has run 43000 copies sir, i have doubt is it scanner or lazer problem?...

[@radhakrishnastationery1296]

sir we cleaned as u told , the problem has been solved , but new problem started ariving , a thick line is arriving at the top. can u figure out what is the problem ?

[@radhakrishnastationery1296]

sir its a white line, images is diapperaing in the particular line ..its a horizontal line

[@MrRicoh]

If you left the DRUM UNIT in the sun for the repair, it could be exposed to light. I would replace the OPC drum and Cleaning Blade.

[@sohailfarooq1232]

I have changed drum and roller now it copiies blank pages ricoh 3053

[@MrRicoh]

You installed the Charge Roller wrong, probably bent the wrong way plates next to the charge roller. Check it out and correct it. KZbin SUPPORT: kzbin.info/door/OHtXTtGHj33pUm8Gf2FH3Ajoin PATREON: www.patreon.com/CopyExpertMovieStudio PATRONITE: www.patronite.pl/1796

[@vidhyadarshans5300]

my ricoh mp 2001l print quality is become too light. just like very low resolution printing. what is the solution ?

[@MrRicoh]

Hello, Please, write to me what the counter of the copier is.

[@vidhyadarshans5300]

@@MrRicoh 200000 i was changed drum blade and devloper at 130000

[@MrRicoh]

It means that everything is fine. The developer has a capacity of 60,000 copies so it's time to replace it again. Remember DRUM, BLADE CHARGE ROLLER DEVELOPER, always replace every 60,000 copies. However, every 120,000 copies, replace FUSER ROLLER, PRESS ROLLER

[@rorycayson9222]

I realize it's kinda off topic but do anybody know a good site to watch newly released series online ?

[@xanderkashton1305]

@Rory Cayson I would suggest Flixzone. You can find it by googling =)

[@sohailfarooq1232]

May i ask a question

[@MrRicoh]

Yes please. KZbin SUPPORT: kzbin.info/door/OHtXTtGHj33pUm8Gf2FH3Ajoin PATREON: www.patreon.com/CopyExpertMovieStudio PATRONITE: www.patronite.pl/1796

[@sohailfarooq1232]

@@MrRicoh my nachine ricoh 3053 ask for add toner, i have changed gears drum,developer and blade as well. When i start machine at a sudden it gives beep and says toner depleted, then it says add toner. When i remove toner assmbly and starts machine it gives add toner, it means error is from the unit other than toner assembly.

[@erwinopis1538]

Sir what is the name of the developer

[@MrRicoh]

Developer Ricoh (D1589640) MP2001/MP2501 60K Don't forget to subscribe to my channel.

[@nehalmodelingstudio]

591 err ka solutions

[@MrRicoh]

Description: Rear exhaust fan motor error The CPU detects an exhaust fan lock signal for more than 5 seconds. Causes: - Loose connection of the exhaust fan motor - Too much load on the motor drive