5 Things To Know Before Buying A Mazda RX8

[@SaigaiStreet]

Seeing a Rotors Magazine video in the sub feed can turn bad days good. Love the videos man!

[@ntgam1ng252]

From a real rx8 owner here is what you should actually know about the rx8 if you're going to own one since this guy doesn't know what he's talking about. 1. Do not use the factory rated 5w-20 oil, its too thin and leads to excess wear on the engine. 10w-20 or even 10w-30 is better in the warm weather. 2. Let the engine warm completely up before driving in the winter and in the summer keep the rpms below 4k until its warmed up, revving while cold kills rotary and really all aluminum block engines 3. Never run low grade fuel unless you want to kill your performance 4. Check your oil often as they burn oil naturally, white foam in your oil is normal don't freak out 5. Once a day rev the engine to 10k rpms, this clears excess carbon out of the motor 6. Rx8s are track cars not drag strip cars, race on a circuit or autocross. 7. Do not start the car and turn it off unless its fully warmed up, if you do you're risking flooding the engine. 8. If you have to turn the car off early you need to rev the engine to 3500rpm and turn the key to off before the rpms drop to 0 this helps clear fuel and oil out. 5 year rx8 owner, these are the most important rules to follow, everything else is the same as any other car

[@Slyfer]

asmithdev I just like the look, is it okay if I get regular? I don't plan to speed it or anything

[@Slyfer]

asmithdev also what is rpm? I'm just getting into cars, idk much

[@breeston]

rotations per minute or revolutions per minute

[@dk7541]

asmithdev I did the same thing and my 8 never failed me. this is the best advice you can have. do these steps and your 8 will run forever

[@KyleHaleInTheCut]

Slyfer Lmao what

[@petelewis4164]

thanks for the video. I'm a long time owner of an RX8 (11 yrs) and there are three main rules for a healthy Rx8 that I have followed. 1. Pre mix your fuel with a good 2 stroke oil. 2. coil packs. either change the mazda coils every 30,000 miles or fit the good aftermarket Ls2 coils. 3. Cooling. keep your engine cool. I've fitted an upgraded radiator and a 76 degree centigrade thermostat. As an extra tips make sure both your cooling fans work as they are prone to failure. hope this helps and happy Rx8 motoring.☺

[@THEMISOGYNISER]

Pete Lewis wait its like those old bikes? you need to mix oil and petrol? fucking useless

[@DanielFreakinAwesome2]

Old bikes? You mean two-stroke dirtbikes right? The ones that they use in motocross? Boy, you sound fucking useless.

[@brando555555]

Right? 2 stroke engines are the shit. They're easy to build, tune and modify, and they make more power than an equivalent displacement 4 stroke.

[@andrijajokanovic8396]

mate 2 stroke is great and there is nothing wrong with adding oil in fuel its not at all hard to do

[@roji556]

+Daniel Kane Two Strokes aren't used in Motocross anymore and Two Stroke bikes aren't made anymore. All dirt bikes are 4 stroke now.

[@TheSnowLeopard]

Step 1: Become friends with/marry a mechanic Step 2: Purchase RX8

[@jamesmuffins3330]

Our family has like 3 mechanics in it and 2 more that work on their own cars. Not exactly a problem for me!

[@invertedv12powerhouse77]

lol i decided to become a mechanic. Only temporarily but the knowledge I gained is incredible.

[@justarandomdude9346]

No bro you got it wrong... Step 1: Marry a mechanic Step 2: Marry a gas station owner Step 3: Buy an rx8 Step 4: Be overprotective Step 5: Have tons of fun and beat the shit out of it, it helps with the reliability (no joke)

[@wesd8816]

Finally someone who knows what they're talking about. Anyone who owns or wants to own an Rx-8 should watch this video.

[@tim83h]

Frequent oil changes and redlining are key! My Series 1 has over 170,000kms original engine and still going strong.

[@fiee_journal]

Hi mate can u tell me how u maintenance mazda rx8 series 1 ?

[@psilence0]

What's a series 1 and series 2 rx8?

[@sheebify]

@@psilence0 Pretty much the first Gen was from 2003-2008 and the 2nd from 2009-2012 You'll easily spot the difference when looking at the grills

[@bluspectre2042]

@@psilence0 The noticeable differences are the changes in the tail-light design, front bumper and grill, oil pressure increase and a third oil injector. Finally, they unified the engine and trans options from the S1 having literally every mix-n-match option you could think of into only 2 options: 6-speed auto mated to a 6-port RE and a reinforced 6-speed manual mated to a 6-port RE. Simple. Made choosing the right car with the right engine so much easier because there were literally only 2 options.

[@arborinfelix]

I have mine almost for over 2 years now. At the time I bought it I was very uninformed about Rotary engines. So I concentrated my energy to get to know the sellers. I wanted to see how they treat their other cars or if they had the money to take care of the RX8. In the end I bought mine from a man his the late 40 who had two brand new BMW's (530 and a 5 series station wagon). His reason for selling the RX8 was his sons coming 18th birthday. He wanted to get rid of the car before his son was able to drive a too powerful car for a new driver. So I got my very clean all stock 2006 6 speed manual at 70000 km for almost 9000€. Now I have almost 95000 km and I never had a problem.

[@cbremer83]

Great vid! Been very happy with my 09 S2 for the last five years. Aside from squeezing wider 245 Nitto tires on the stock rims, it's untouched. Got it with 24K on it. Has 64K on it now. Despite some people's objections, been running royal purple in it. Zero issues. Burn clean and when I pull the plugs they look perfect. Slight brown ash, like normal. It is due from new coils again. But it still runs strong. That being said, I have been thinking about getting ready for a rebuild before issues crop up. Maybe next winter. I will be at around 70K by then. It's not my daily driver, so the downtime is not a big deal. I having it ported while the engine is out. I know it won't add much, but I figure it's not a huge expense for the gains. At least it's not a lot in the overall cost of a rebuild.

[@jackdillane1482]

I own an RX8 S2 and there's so much nonsense in the community. I really appreciated this video and I look forward to seeing more!

[@azuki_the_r3]

Thanks for making this video and stating that the negative reputation of the RX8 is undeserved. I have a Series II, and had a Series I as well, and both served me very well! Granted, I did do my research, and wanted to genuinely know more about rotaries. I love and adore my RX8, and is going try and use my car to break the cycle and perception of its negative reputation.

[@LT-jc4qb]

Hows the breaking of the negative the perception going? It has a negative reputation because of the amount of maintenance and inherent flaws the motor has. So unless you can go to a non-car enthusiast and explain why an RX-8 is better than a traditional car with the same performance stats and convince that person to pick it over the traditional car...your attempt is moot.

[@JDMcam702]

#4 Was a good point. I would highly suggest anybody wanting to buy in rx8 to buy series 2 rx8.

[@UzY3L]

He's right. I've been reading about the RX8 on the forums since October last year. Everyone is right and everyone is wrong. But what I did get from this : replace the coils, keep an eye on the temp, use 10W40 mineral oil, don't rev it when cold. That's the basics but it goes a long way in engine life

[@rotart12arx3]

So what you are saying, it is fragile engine that can't survive unless it is treated much differently from a normal engine that will go 200k with normal care.

[@threadworm437]

@@rotart12arx3 it's a completely different kind of engine, it's obviously not gonna have the same types of needs. Plenty of pros and cons compared to piston engines

[@rotart12arx3]

@@threadworm437 I know it is, I have owned 2 RX-3 and 1 RX-4 and 2 RX-8. My 2004 was not so good and my 2010 has been great. They just won't last as long as a good piston engine even with perfect care.

[@fnsonicrick]

I have owned a series 2 since I bought it Brand new in 2010. Best car I have owned all my friends cars have broken or been lost some way since then. I've spent a lot on maintenence but zero on repair. going on 85000 miles now. and it surprises me on how fast it is.

[@151LT]

I'm looking at buying a 2004 with 137,000 miles, and this video addressed like 70% of what I was asking about.

[@doktorbimmer]

*You would have to be very gullible and naive to buy any RX with 137,000 miles!*

[@Numbah893]

I've thought about getting an RX8 because I never owned a rotary and I've thought about getting one. I've done bits of research here and there for these cars. Premixing is more ideal to keep maintaining your motor better from what I understand. For power wise you can make power but you can't. Honestly I don't look to shoot for crazy power with it. I would want to at least bridgeport the motor and put your normal bolt ons the car. Hearing these motors brap at idle really grabbed my attention. I look to take apart a Renesis that needs a rebuild because I can get an understanding how it all works, how it's taken apart and what goes into rebuilding one. I'm in Florida just 2 hours north of Miami and it would be nice to meet other rotary enthusiast I could learn from.

[@Bloodfire936]

Awsome video and totally agree with everything especially #5. I looked at a lot of these cars before settling on my R3 and you wouldn't believe how many owners had no clue what they owned. Some didn't even know there was a rotary engine in it. Channels like this and sites like rx8club have a sea of information that can help an owner/buyer immensely. Loving the channel and looking forward to more content.

[@jestomacco1594]

Thank you for the helpful info. I always wanted a rotary and I just got a rx8 for free yesterday so this vid really helps on the negative perspectives that people talk about thanks 👍🏼.

[@WesSites]

Same thing has happened in the Subaru community. People like to trash EJ-257s for being unreliable. It isn't that the engine is bad, it's that it has it's quirks and you can't just beat the hell out of it before it warms up properly. The problem with most used performance cars is that they weren't treated well, that's coming from someone who has owned several used performance cars and had issues with some of them. NA cars tend to be less of an issue, but turbo cars are a mixed bag. People beat on them and don't let the turbo cool before shutting the car off. The oil pump doesn't circulate oil when the engine isn't running and therefore oil is trapped in the hot turbo and is turned into sludge because it's taken far beyond it's operating temperature and then you have a poor lubricant and boom, there goes your engine after a few thousand miles.

[@skylergabriele6445]

WesSites wrong. The ej257 and most turbo engines have coolant flowing through the turbo after its shut off, you do not need to let it cool down unless you full throttled into your garage and immediately shut it off.

[@WesSites]

Skyler Gabriele hey dumb ass, no they don't. The oil pump shuts off when the engine shuts off, it runs off the serpentine belt. It doesn't have an electric power source that keeps it running. I own an STI, I'm well aware of what it does and does not do. The only thing that cools the Turbo is oil, antifreeze would vaporize if you ran it through the Turbo. You obviously have zero knowledge about automobiles.

[@invertedv12powerhouse77]

@@skylergabriele6445 no turbo is cooled by prestone as far as im concerned. And heck its not cooled, more like its lubricated

[@invertedv12powerhouse77]

Well, heres another thing. The ej257 is an aluminium block with thin cylinder walls and basically no support at the top of the block, so the cylinder walls move around in high boosts and can cause headgasket issues, and the cylinder walls can also crack alot easier. Theres also the fact that it uses cast pistons, that are somewhat large, and weak rods. The ej207 tends to be more reliable, because the walls are so fucking thick that they barely move. Also the fact that some came with forged pistons

[@LT-jc4qb]

@@skylergabriele6445 dumbest attempt to look smart and knowledgeable. Lol. Check your blinker fluid and make sure it's topped off too while you're at it.

[@terencewu3743]

Good review , was worrying about buying rx8 but now confident to buy it

[@javierdelrisco1060]

i have an rx8 150k miles. always premix. i drive it like crazy. 20 miles everyday. and only flooded once. because of my fault. and got back to normal. in minutes. best car ever. and the only engine that has last for so long with my way of driving. i used 5 sets of rear tires in 8 months only. so that tells a lot about me. i had to put oil every 4 days. Still turns on in less than 2 seconds when cold or hot. to be honest. its not the fastest car. but. its the only cat that you can take to the track. with 150k miles. and drive it hard all day... trust me guys. i drive almost everyday. at over 6k rpms for more than 20 miles. engine is as happy as it can get.

[@Daniel-xy6ds]

javier del risco . . . . .

[@615mace]

I actually do have a question.. what do you mix with? Like what are the percentages I should be looking for

[@doktorbimmer]

*Never premix... this is nothing but a stupid urban myth that does nothing but damage your engine. don't be stupid.*

[@nasosgreece45]

I know a guy who bought an RX-8 series 1 and when he needed an engine rebuilt in around 130.000 miles he swapped the most with the 13B rotary engine from an RX-7 and he never had any problems again!! Plus he has twin turbos now!!!

[@doktorbimmer]

*Can't fix stupid...*

[@bertito43]

Had an 04 RX-8 and put 120,000 miles on it before I sold it. Had zero problems with it at all. I removed the cat converter. Always used premix, changed coils every 30k and used water wetter instead of coolant.

[@bertito43]

I also used 20w50 oil and I drove it like I stole it.

[@Rose_Butterfly98]

my friend loves the rx8, she was so sad when it got discontinued. One of my neighbors has a white one, I absolutely love the sound

[@clockwrk7684]

Honestly thank you. I was looking into an rx8 and this really helped me push towards it

[@gamingmadesimple5510]

nice vid.. I have 09 r3 that I daily. I don't premixed and have all original coils, starter, sparks, and wires with zero issues so far... I am on straight pipes but I know that is not possible in many states due to emission regulations but my state doesn't have any emission testing... I meticulously keep up on my maintenance and care for it constantly.. they are great cars very reliable if you care for it properly and great fun to play in... and as you said it's not a power house engine... for dailies I would say a street port and tune with other mods like exhaust and new coils with plugs is about as far as you need to go... just that alone can give you a solid 40whp boost if your tune is good and that makes a lot of difference in how it feels

[@boostusa4688]

I live in Orlando Florida and the thing ppl are doing here is buying cheap or not running rx8 and doing a 13b swap and boost because it's more practical than a rx7 and they are good looking cars. I think you should have mentioned that it's great for doing a swap

[@kamilwilliams83]

I'm supposed to be getting a series 1 RX8 and I was scared cause of what the public said about the engine, but being scared will help me keep that engine great so I'm getting the car I can't wait to pick it up.

[@fiee_journal]

Hi mate, can u tell me how maintenance ur mazda rx8 series 1?

[@kamilwilliams83]

@@fiee_journal Well for starters before buying one you should definitely have a compression test done to check the life of the engine, then try to upgrade your starter, ignition coils and upgrade your radiator as well for better coolant to flow to your engine. Or for definite answers to your question just subscribe to Japanda and he will give you a better understanding.

[@fiee_journal]

@@kamilwilliams83 thanks mate

[@trashpanda112]

Loving the vid! I'm glad someone knows more about rx8's love my r3 second gen. will not swap it, puts a smile on my face every time!

[@CenturionGhost]

What should I look for when buying an RX8!?!? I'm looking at buying one right now, looking forward to that video!!

[@Homemedrunkimtake]

Always ask about fuel economy, if they say anything less than horrible then don't buy it. They most likely ran it wrong and the engine doesn't have much life left to it. Let's be honest, worrying about Gas mileage on the 8 is like re-arranging the deck chairs on the Titanic.

[@BoRuT83]

Thanks for the video 👍I do own two 09 R3's and one 06 Rx8 like I say if you know what you're doing they keep on going p.s: I bought all of them used and they still have original engines

[@joshuafinley644]

I totally agree with point number 4: find a 2nd gen RX-8 because they have far less problems than the 1st gen models. I'm planning on getting an RX-8 R3 someday, which is a 2nd gen car, and I think it would be a blast to own one and have an RX-7 or a REPU on the side

[@ArmandoVictorForno]

I've been looking for some RX-8 deals lately, since the RX-7s barely saw the Italian market. Sadly, most of the times the owners will just skip the engine conditions in the vehicle description. As soon as they start blabbing on how good the sound system is or how comfy the seats are, you know they're trying not to say the engine is f*cked big time😂

[@cedricklee4111]

great info... I am planning on buying an RX-8 and this helped a lot for me. Thank you

[@beaches2mountains230]

ANYTHING BOOSTED WITH INCREASED CYLINDER PRESSURE (OR WHATEVER YOU'D CALL THE EQUIVALENT IN A ROTARY) WILL ALWAYS DECREASE RELIABILITY OR LONG TERM DURABILITY..

[@offthegriducantcontrolme831]

I OWN a 2009 and yes you have alot of great info for new owners and everyone else too.

[@StefanMailey]

Well holy shitt. Someone that actually knows facts. Great video, man. Cheers

[@tribeofjudah1]

thinking of getting a rx8 next year. great video and will take my time with this one.

[@stevewall6811]

tribeofjudah1 I wouldn't waste your money honestly. no offense to rx8s

[@nazarrakhmanov9357]

Wish I had seen this before buying mine... bought first one I went to go see. Found out low compression. Had to replace engine

[@StevDoesBigJumps]

Thing to know before buying any wankel-rotary, fuel economy = hello darkness my old friend.

[@rucarnuts13]

I've noticed you guys don't seem to cover SA and FB RX7's all that much, if at all. What is your opinion on those?

[@fredrenault9012]

there's barely anyone covering the fb, and if they do, it's for 3 videos at most (there are some exceptions, obviously)....and well, the fc should be covered soon as Kenny own one....

[@rucarnuts13]

So I've noticed. My first impressions of them (from online forums and discussions with other RX enthusiasts) is that the SA/FB generation is regarded as a bit of a black sheep in the RX lineage.

[@cbremer83]

It's a shame too. I rather have an SA or FB over the FC. they have a special kind of coolness the FC lacks. At least for me. But, anything rotary is cool for me in the end. Just some are cooler than others. lol Really want an RX3.

[@rucarnuts13]

Agreed. The SA's and FB's seem to ooze a coolness that (IMO) an FC and FD just don't have. They also seem quite a lot rarer than the later FC's and FD's. In fact, I've only ever seen 4 SA's and or FB's - two of which were irreparably damaged and rotting away in junkyards. But anything with a rotary engine just oozes cool. If I had the money and opportunity to buy one, my dream car would be a first-year RX4 Wagon. I'd make it a wicked canyon carver. Maybe one day, I will...

[@cbremer83]

FD is pretty common where I am. Well, by rotary standards. S1 RX8 is more common with FC a little behind the FD. I have only seen a fee FBs floating around. Just as rare are the S2 RX8. Besides my own, only ever seen three others in the area.

[@jorgea279]

what about swapping a series 2 motor into a series 1 chasis?

[@Growthandgainventures]

I've been contemplating getting an rx8 and u have just made my decision so much easier.. Such a great video man

[@crxsleeper18]

ive ran into ppl that owned one and didnt know what a rotary was.. despite all the hate i cant wait to own one

[@kailowe9346]

I live in Canada, Alberta and i'm thinking of buying an 04 R-X8, what are the biggest things I need to do and watch for if I actually end up buying this car. As a note the car i'm thinking of buying has low kms, no rust, no fixes, no accidents, all factory, some dents, and no major problems.

[@patrickalbrecht3333]

Thx 4 the video i am goin to check one of this cars today and maybe i will buy it so i am realy happy to found a video like this

[@sledge6693]

I LOVED my RX8. However, the problems are MASSIVE & the costs just wear you down... Oil, Fuel, Servicing, Insurance, other issues (E..g. Clutch, Brakes, etc). Then there's the engine dilemma, which is essentially like buying another car. Mine only lasted 2 years. It was my baby & I took care of it, but the reliability issues are very real.

[@chiefzaydoe1466]

Jeez man.

[@RickSuaz]

I'm picking up an rx8 this Monday. I'm going to be cruising with this. I'm not into racing not even speeding But I've always loved its look. So I know my engine will last me.

[@rotart12arx3]

Better get a compression check.

[@thomashuckaby8867]

Very informative video explained by an obviously well informed presenter w/o any objectionable language..Thank you!

[@santosgtz7011]

i was a little iffy abt getting my brother one today to practice. hope it goes well it looks dope

[@Kill3r360]

2:20 ye but the rx7 you talking about is the fd which cost 30k cad minimum where the rx8 even tho over priced is between 8K to most being around 10k cad

[@blakesiladji]

this vid completely explained the rep of reliability issues of the rx8 now im looking at them in a completely different light! thank you for that as i saw them as a boil on the ass of rotories in general good job mate very informative

[@doktorbimmer]

*Today marks the 6th anniversary of the end of RX production, on Thursday June 21, 2012 at **4:30**pm the very last RX car ever to be produced rolled off the assembly.*

[@sandervanderkammen9230]

9 years now

[@jolmeaki]

A friend's nephew just sold his RX8 for $1000. 2004 with. 130k on it. His mother made him sell it and it needed a clutch. Wish I knew but I'm in NY and he's in VA.

[@chrismedia234]

I have 2009 rx8 used to be my pops he gave to me since he bought another one but 2005 so ive been informing him how to give maintance to the engine. Hes a rotary guy but the rx8 engine needs more maintance. Going back to the 09 right now it has 136k miles and going so i cant complain. I know is not necessary but i premix sometimes just to make sure the engine las longer.

[@doktorbimmer]

*Bullshit! pre-mixing is not only dumb! but does nothing to improve reliability.... just damages the engine even more!*

[@jonnyboyjs22]

i drive hondas but love this channel so far , subscribed :)

[@Dr_Disconnect]

great video bud. I've been bouncing between a rx8 2nd gen, hyundai genesis coupe, bmw 128i-135i and a bmw 2002. But some how i keep coming back to a rx8.

[@thatotakubear1150]

Great video, especially as I am looking to buy one soon, but I do have one complaint/suggestion. Modifications like a CAI or catback exhaust are more than just power adders, they also improve throttle response and make the car more fun to drive.

[@michaelward5719]

Great video, I'm a prior Aircraft Mechanic and I love anything that turns. I had an 85 RX-7 and since then I've been in love with these cars. I've hesitated more than once on buying an RX-8 due to the rep. I will reconsider, maybe an R3. Would you recommend, or not applying a small amount of boost or total stock? Thanks, Mike

[@carbonseals]

A good write up on the Rx8 mate. Unlike many others I’ve had a couple of rotaries and even more engines, and there is so much misinformation out there it actually makes me angry…younger idiots who think they know it all…I was playing with rotors when they were in kindergarten! Always read the stuff from Mazda, get some info from racing teams and talk to the rotary specialists, some are specialists and some not so much. Look online , read the books and you should be able to sort the hay from the chaff. 👍

[@rambow70]

Do people often put the series two motor in a FC/FD rx7 because of these improvements along with the aluminum cast or do they opt for the iron cast to be able to make more power? I always wondered how similar 13b's are.

[@KennyatHumble]

It's typically the other way around, FD swap is the 'power' swap. The Renesis isn't liked too much outside the RX8 community.

[@davespooney8472]

Very informative video, thank you! Don't know what the pricing like in the US, but here in the UK, with that reputation, higher car tax and low MPG, you can get a 55k mile minter for a little over £1k, or $1250... you literally cannot give them away. I mean with a fresh engine they should be £4K+ all day long. Such a damn shame, they are disappearing FAST

[@vladimirmilev191]

Great video it helped a lot! I bought a mazda RX8 and i wanted to ask what is the reasonable power we can achieve and how do we do it?

[@MJTAUTOMOTIVE]

Hi Rotors, Best video yet good info and I like the way you talked about people with no knowledge on the engine. Keep it up Guys Cheers Mark.

[@HastelloyC276]

How is the insuance? How is the insurance compared to other cars?

[@unknownuser2357]

Thinking about this for my first car...Im really fixed on a paddle shifter or automanual

[@ContradictoryCom]

i have a 1st gen 2004 rx8 and its caused me alot of pain and suffering first thing to go was my clutch( my fault learned stick on this car) and then after fixing i believe i blew the engine. just lost power on freeway. wish i had more information to fix it...

[@Homemedrunkimtake]

Well do some research. These cars are really unique in terms of maintenance and driving. They're great cars. I have one right now. On my second engine right now. 1st lasted me 190000km including track days.

[@ContradictoryCom]

Homemedrunkimtake did you replace or repair your engine?

[@Homemedrunkimtake]

"Rebuilt" by Mazda itself. They're apex seals are quite "Problematic". Other than that tho I'm quite happy honestly. I always put High Octane fuel and premix with Idemitsu before every fill up. Clutch is a Bully stage 3 "Steel and Kevlar" complimented with an ACT Prolyte flywheel (11.5Lbs). BHR upgraded ignition system and Racing Beat Cold air intake and Cat Back. Built it myself from ground up. Dyno'd in Montreal @ EK Performance and doing 247HP at the Flywheel. You really need to understand and treat the car the way it should be and you'll be happier than the next schmuck with a GT86 pushing 200HP.

[@Homemedrunkimtake]

And it's Always better to "Rebuild" than to buy used.. Reason is because you don't know what that engine has been through. It could be at 50 000KM and still die of mistreatment. Rebuilding gives you the opportunity to see in what shape your engine is in.... And I'll be honest, most compression loss are due to seals and stuff. The rotors and housings actually last long! Look up the 787B Mazda. It raced in the LeMans 24H race and once it won, (Which is actually the only Japanese car in history to have won), the engine was in such great shape after the brutal 24H that they could've used it for another 24H!

[@levelvtl]

Very interesting video!! Keep them coming!

[@davelowe1647]

In the next one can you address the hot and cold starting issue please. Also how to rectify it?

[@whosCatch22]

So would I be okay to throw a turbo on an an exuadt and whatever else and have fun drifting?

[@masjuggalo]

from experience it's plan a motor swap 13b/20b/lsx...

[@abexlvii6269]

What do the think about the 40th anniversary? Is it reliable as the second gen?

[@BRZ_RN]

this channel is cool, i hope the fa20 community has something like this.

[@rillestworks7192]

I'm gonna take your word you look very passionate about your rotarys

[@lamma109]

thank you I've been thinking of getting an rx8

[@cbremer83]

five year S2 owner. Love it.

[@lamma109]

Update: Got a low mileage 07, and man is it a blast

[@yeahbuddy1322]

how are you finding it now? does it burn a hole in your pocket on fuel?

[@Molzhon93]

Yeah Buddy I'm wondering as well, might be buying one Thursday.

[@Reefer-Rampage69]

Damn, I miss my RX7 so much. I want another rotary 😭

[@angelward8367]

thank you for the video I'm looking to buy a rx8 soon and have alto of questions. I'm not entirely sure what too look for.

[@Tablas888]

Is the next video already released? about what to check before buying an rx-8?!?!

[@luisk6007]

What modifications will make an RX8 last longer? Stuff like aluminum radiators, maybe LS coils etc.?

[@luisk6007]

oh, is this a car with a case of $12,000 ENGINE REBUILD SOOOOOOOOOOON?! jk There's a lot of rotary specialists here in Puerto Rico, but I see that all they do is make A FUCK TON of power.

[@rucarnuts13]

Luisk - Points for the RCR reference. As far as reliability mods go, just do the usual. Use the proper oil, premix, maintain it well, an aluminum radiator could help and then drive them in the manner they like to be driven. Also, if you're talking about a Series 1 car; then upgrading the oil metering pump will help.

[@ntgam1ng252]

3:00 the rx8 was rated 255 and later revised to 238hp from the factory, any modification that removes restriction on the intake or exhaust or drive train losses will result in far more than 250hp so that statement is inaccurate, breaking 240hp is possible with pretty much any mod

[@askmewhatyouneedtoknow5342]

My 2007 ‘Mazda rx8 Shit stars when it’s cold but after running on 40 mph it feels like it’s getting slower it’s not running how supposed to and ones sometimes when I stop it started tumbling and After I turn it off when I run It for like 30 minutes and it doesn’t wanna turn on sometimes The Kranks it is still cranky but sometimes the battery dies

[@adityaakula9434]

I could not find a decent 09-12 rx8 in houston and had to go for an 09 autoi .. I love the car to bits but it leaves me wishing for a little bit more power (probably closer to the manual version)... I am a strong believer that light handling car should not have more than 280 hp max ..but I am stuck at 212 and cant find a way to make that extra 40-50 hp .

[@SpirosAliprantis]

Are there any engine codes from the NA Rx-8 to the NB Rx-8? Because I am planning to buy an Rx-8 which works and it is very cheap and swap the engine right away. Any better plans to that?

[@MrFusion101]

only struggle to make 200hp+ from a 4 port, my special edition is 6 port and 238 from factory

[@justincooper5189]

2 questions at the moment: first one: does mazda make a good non rotary engine that can be swapped into an rx8? and number 2: are the rx8's still produced? i heard something about them being discontinued, but i don't know if they were a reliable person to believe.

[@justinschermetzler5293]

Yes, the RX8 has been discontinued. I believe the last ones sold in the U.S. were 2011 models and I think there were a limited number of 2012 Spirit R models made overseas for their grand finale.

[@justinschermetzler5293]

As far as engine swaps go, you can put just about any engine in any car with enough money and creativity. Most people who do it just put a Chevy LS crate engine in there. In my opinion though, anything other than a rotary in these cars ruins what the car was built for. Just about any piston engine you put in there will destroy the near perfect 50/50 weight ratio and raise the center of gravity, both of which would have a big negative impact on this cars handling. If you're looking for more reliability or pure straight line power, an RX8 is not the platform to start with.

[@justincooper5189]

i normally like to keep a car with the same company engine, such as mazda having a mazda engine, mainly because of finding parts. i figure if mazda makes a non rotary engine, it can fit in an rx7 or rx8, and it shouldn't affect the weight too much because mazda would figure on something like that happening.

[@gucci4871]

Good video, informative,and quick clear to the points.👍

[@sharpemang]

I want an RX8 because I have a tendency to redline a piston car on a regular basis and I like my cars shooting flames.

[@Deathcore615]

Is a Rotary engine easy to build? Easier than a Honda B or K? I kind of want to replace my project integra with a project FC Rx7

[@Halsafe]

They are easy, but stick to K series

[@propokerking]

thanks dude, this video was very helpful A++++++++ keep them coming

[@Duk3Nuk3m85]

I've been thinking about one thing. Can i use a RX8 as daily driver even in the winter months? Here in Scandinavia, we can have up to -25c some times.

[@bortiz5260]

What year of the rx8 is the best to buy ????

[@SYLVANIAG]

So I have been curious about this for a while now but, if you buy a series 2 RX-8 (2009-2011), Do you still have to / should you still premix?

[@doktorbimmer]

*Only uneducated imbeciles pre-mix... this is the biggest false urban myth*

[@karlwitty4129]

With the series 2 09+ do people still premix along side the normal oil would that be wise or is it purely overkill. Cheers

[@theangrycamel1045]

i'm a student i have a part time job, I've heard that it is an expensive car to run and i would like to know your opinion on how much i should spend on the car. Also if it is worth buying as i will not being doing very long drives ( At most 5 Miles a day). I would really love to get one but i;m a bit worried about purchasing it.

[@iTzDarking77]

Hi, I'm thinking about buying a RX-8 as my first car, and I would like to know what should I look for when buying one, things like if the compression is right, the apex seals are good to go... And how often should you premix, and if it's expensive for a 18 years old guy studying to maintain and take a good care of the car. And without a large income lol

[@Bokie469]

Alvin King Normally you're supposed to pre mix, every time you go to the gas station. I use idemitsu pre mix. And it say's that you're supposed to use like around 1/4 oz per gallon of gas. Something along those line. The actual measurement is on the back. I'd recommend you buy it in bulk. I pay around like $120 for a box of like 30 or so Quarts of Pre mix.

[@Bokie469]

Alvin King I use Idemitsu oil too, and I run with 20w50 grade oil. Since Idemitsu is the only Synthetic oil I'd recommend. All the other companies minerals will be horrible for your Housing walls etc. 13B Renesis uses around 4.5 quarts of oil just FYI. Hope all that helps, I do all this and my RX8 currently has almost 140k miles on it. Original Engine and all 🙌

[@johndoumenis7956]

I have a question can you take the oil injector system from a gen 2 and put it on a gen 1 ? If anyone know something please help me

[@dot_boi]

Would you recommend an rx-7 or rx-8 for a daily driver? If I bought an RX-7 I could pick one up for around 1.5k to 2k USD and most of them around here have ~100k miles. I have the tools and equipment to pull and rebuild trannies and motors and pretty much do anything to the car so It would be much more affordable. Or I should save a bit more for something like an 04 rx-8 which go anywhere from 3k to 8k around here depending on the miles. What do you think, an older rx-7 or a newer rx-8?

[@KennyatHumble]

Amadax 09+ Rx8.

[@joelindooo]

What about getting a paddle shifter Mazda RX-8 Grand Touring? Can that be fun?

[@mortistio]

im looking into buying an overheated RX8. so obviously ima be doing some work on it but my question is, is it worth it to buy this one and rebuild it or better to buy one with minimal to no problems?

[@billytheaspiringgsxowner2475]

I really want to daily a rx8, I think I am going to start saving up for it after I get a car, but there are some mods I want to do if I ever get the chance, exhaust, supercharger, intake, ignition, radiator, cutoff oil to housings and premix the fuel, somewhat grippy tires coilovers and wheels, how reliable would it be making around 300 to 350hp

[@jamesmuffins3330]

If you're planing to do that, might as well get an RX-7. They perform much better and is a better RX platform for Perf parts

[@reggieflores5263]

hey i swap my cbr250rr mc22 to my friends RX8 it has 14K on the meter the car is running OK i think power is OK the only problem is it takes 5 to 8 sec. to start..! some time more. is that normal..? do i need to change something? its my 1st time on rotary

[@doktorbimmer]

*Your engine is FUCKED! sell that POS for scrap and consider it a lesson learned.*

[@HardBed816]

Are you from Kansas City MO