RS5 b8 Removed and Install new gearbox DL501 0B5

[@RMcarphotography]

Great work into the extra added information and elsa pictures. usefull.

[@RmProjects]

Thanks 👊

[@boba_driver]

Golly! That sounds better than my setup and I thought mine sounded perfect.

[@camhyde9701]

Good news pleased to see its fixed

[@JJP.GT3]

Extraordinario brother..👌🚗💨💨

[@stefanoprinci5664]

Very well put together guide. Can you remember what size socket size is required for the bell housing bolts (ie. the 12 point bolts attaching the body of the transmission to the engine block shown at 4:47 ), are they 18mm? Thanks

[@johnbrunjes3414]

Where did you find the VAG guide?? Need to drop my 3.0t engine for timing and would LOVE that guide

[@bbocjcp]

That top heat shield bolt on the left hand side is an absolute bastad to remove and re-fit. I ended up leaving it off when I replaced the drive axles on my A6

[@2shots1kill]

What was wrong with your old gearbox? How long did it take you to replace it?

[@boba_driver]

Are you on a stock tune? Where did you find the replacement gearbox?

[@nejipsila7897]

Hello, can you tell me where you found your gearbox?

[@Sam-vk3tz]

Hey RM, I will be shortly getting the gearbox on my RS5 overhauled along with fitting a JHM Lightweight Flywheel - Question I have some catless headers that need to be fitted are the OE manifold accessible with the engine in situ but gearbox removed?

[@carmotion101]

👀 I'm the first to watch 💪🏾

[@RmProjects]

❤️🙏

[@eega100]

What exhaust have you got?

[@lucaskaufmann6453]

How many kilometers did your old gearbox had? Is there a difference in the gearbox from the pre to the facelift modell?

[@RmProjects]

my old gearbox has 86000 km on the clock & yes the megatronics would have an adjustment and the external ATF filter has also been adjusted! the 2010-2011 filter housing has come loose due to vibrations while driving

[@hivepixels]

It wasn't clear for me what was wrong with your gearbox. What fault codes did you have?

[@TheManmoths]

Good to see that fixed it! What was the cost for the exchange?

[@RmProjects]

I'm glad she's okay too😅 The cost list Gearbox 1200 euros + 2 months warranty MTF oil 100 euros ATF oil 60 euros Gasket ATF 15 euros 2xfilter ATF 35 euros Orings set 12 euros Copper rings set 10 euros I spent about 35 hours on it But that's for my own

[@weewouclaps]

Look like a 10k job

[@z06dave]

I'm having an absolute nightmare with mine. I think the mechatronics unit is failing as it randomly gives me gearbox fault error message and goes into limp. Audi won't touch it because It has a map (by mrc) by the previous owner. I have no idea what to do

Good to see that the issue is fixed. Have you conisdered to open the original gearbox and find the root cause?

[@RmProjects]

no i haven't done that yet! but I still think the Diffrential made the sound! but I will still disassemble the gearbox because I find it interesting what the causes were

[@commenkid1]

Do you need to do adaptions to new gearbox or is it simply a plug and play?

[@moonwave86]

​@@commenkid1 since the TCM is driving a different clutch pack, adaptation is required

[@MICHAELRAMCHARANHOLDING]

Kan ik de computer vervangen zonder de bak eraf te halen of is het aan te raden om die er wel af te halen in verband met inlichting of iets anders?

[@RmProjects]

@m.s.ramcharan5441 Jaa je kan mechatronica eruit halen zonder dat je bak eraf moet, je moet wel op letten dat je recht naar beneden gaat anders kunnen schakel vorken verdraaien waardoor je de mechatronica er niet uitkrijgt. En voorzichtig als je de mechatronica laat zakken deze zal een beetje vast geplakt zitten, ander kan je boven de mechatronica plastic kanalen beschadigen! Je kan niet zomaar een ander mechatronica/computer installeren, je zou hem opnieuw moeten (in leren)

[@MICHAELRAMCHARANHOLDING]

Top!! Ik moet de positie sensor vervangen. Neem aan dat die wel gewoon vervangen kan worden zonder inleren. Heb je nog tips of dingen waar ik rekening mee kan houden. Of die ik gelijk meekan nemen en vervangen.

[@RmProjects]

@m.s.ramcharan5441 Voor de positie sensor moet ik je helaas teleurstellen 😞 daar moet je hele bak er voor onderuit, omdat die midden in de bak zelf zit en niet bij de mechatronica! (Je bak moet gedeeld worden om erbij te kunnen)

[@lauradevonport6176]

Hi. Did the gear box need coding/learning with vcds or was is simple plug and play?

[@masonvaldez6987]

jump scare at 5:50