Qual a kilometragem?

erg behulpzame video! welke merk heb je gebruikt en waar kan je die halen?

The noise of working better than those useless music

hoi Richard, Welke pakking heb er ervoor gebruikt is dat van papier groet

The silver piece removed in the beginnings with heat; is that an OEM part of aftermarket wheel spacer?

great video. how did you get the bearing shell out of the cover? is it easier to remove? Thank you

Bedankt voor deze video. Was de speling na het monteren van de lagers dan weg als je de homokineet vast pakte? Mijn a6 c7 avant 8 traps automaat heeft hier ook speling op. Maar als ik het goed zie zit deze enkel in de spline en steunt deze niet in het lager. Dus zal er altijd speling in zitten? Alvast bedankt!

Tipp: Schau das du eine gute Verbindung zu einem VW Autohaus bekommst. Meistens kannst du bei den Teilepreisen etwas handeln und bekommst so 50-100€ Rabatt.

Danke für die Erfahrungswerte. Ich glaube ich hab mal das Video geshen wo du den Bremsenservice mit den Nachbau Bremsbelägen gemacht hast. Ich hab mich schon gewundert dass das geht.

In the front SGL Ceramic brakes and in rear SHW steel ?

Always those HPFP's and the Hydros Failed on so many RS6 C6, 2.0 TFSi's and TSi's it's crazy.

Witam. Jakie jest nr oryginału tej pokrywy aluminiowej?

I have the same one.

I have dl382 - and this boxes from audi are such a piece of shit.

That top heat shield bolt on the left hand side is an absolute bastad to remove and re-fit. I ended up leaving it off when I replaced the drive axles on my A6

The stamped Pagid Logo on those pads makes me happy 😊

They look like standard brakepads 😅

What was wrong with your old gearbox? How long did it take you to replace it?

Top ta vidéo ! J’ai le même problème sur mon A5 mais avec du jeu latéral sur l’arbre à bride 0B4409344A. Est ce que le segment arrêtoir bloque bien l’arbre à bride après remontage ou il y a un jeu d’origine ? Sur ma voiture j’ai l’impression que le segment arrêtoir ne fait plus son travail et l’arbre à bride est libre ayant pour conséquence qu’il tape dans le différentiel me causant un bruit de claquement en roulant.

NE YAĞI KULLANDINIZ

you doing a good job better then dealer and very clean at the engine area

Attempted this today when I did my spark plugs, unfortunately the two torx bolts that hold that metal plate that civers the sensor are seized on, not quite evident in your video but how did you remove those? And did you need to remove all 3 or just the one by dips tick tube and near the strut?

Nice to see X-Pipe in front, recently bought RS4 b8.5, and saw all other video's with X-Pipe at the rear that did not make sense, based on research

very good video .thank you to let me see it

Hi! Great job, what kind of oil did you use after the repair!?

Oh wow! That’s some serious power and symphony

This podcast is extremely helpful to Audi RS5 owners worldwide brother, thanks so much and keep the content coming..

really good video and precise, but you forgot to show how you mount the bearing race in the gearbox in the back 💗👍 Can you fix it and show us how you did it ? Please

Done the same mistake . Thanks for the part number !

Hello, can you tell me where you found your gearbox?

What symptoms did you have before putting the support on? Any vibration or noise?

Clearly this isn’t a diy lol 😂 Good vid 👍🏽

every how many KM is an oil change recommended? The on-board system indicates in 28'000km or 350 days. That's far too long, isn't it?

Hoi Heb jij enige ervaring met gearbox malfunction / position sensor fault?

Nach dem Reparatur war alles ok?

Good day, I Have a few questions for you.

Genau gleiche Problem ist bei meinem Audi.

hello why did you not change the 2 pumps?

Pouvez vous me dire sur quel site commander les pièces

Deleting the system did not throw the error light? Eny coding required? I would appreaciate your answer, planning to do the same on my rs5

Great video! Have you used fuel injector cleaner in the fuel tank? If so, did you notice a difference and can you recommend one?

Well done, what a great job and the video. I got question if you can answer me please. I think I got same problem on my A6 C7 2.0 tdi. But seems your sides are identical while mine one is same like yours on right side and different on left. Thanks!

Nice job

Can i get the full details for this exhaust please?

Did you have to remove the rubber piece in there before installing the upgrade?

Saludos a cuanto se calibra n las válvulas de admisión y escape de este motor

Extraordinario brother..👌🚗💨💨

Great video.Where can i get the washer that you use,before you put the bearing OB4409218C ?What part number is?Thanks

What pad setup are you using in your RS5?

Nice prof work