RSSI, SNR, Link Quality and Failsafe explained

[@charlesmarseille123]

video quality in this specific video is awesome Pawel. You should consider using this setup more often :)

[@DontEverGrowUp]

"Because shit happens." That pretty much sums it up. :-)

[@flywithtb5005]

Correct me if Im wrong: RSSI: past reading of how strong something detectable (the signal) was Misleading if: the signal of surrounding transmitters overlay the original signal and make it impossible to decode (e.g. WLAN in Urban area) SNR: strongness of the signal compared to the strongness of other transmitters or strongness of interference (like a tree in the way?) Misleading if: one noise source has more impact on the transmission of packages than another bcs of frequency or something (else) with same dezibels of noise LQ (Crossfire): number of in the past received and decoded packages Misleading bcs: it doesnt know how many packages have been transmitted.

[@MrGazhay]

I wondered why analogue rssi in osd and rssi on my transmitter never matched. Thanks for the explanation! 👍

[@vojtechvejsicky1819]

what?

[@NoAgendaFPV]

Great explanation of a often confused subject!

[@FPVUniversity]

thanks mate

[@MUNKYFPV]

Interesting, thanks. Something I reckon has saved me a few times is I set the drop when no pulses failsafe delay in betaflight to at least 1 second, I think default is 0.1 second. I reckon this might have saved me a few times where I got a loss of control and the quad just continued on at whatever position the sticks were in because the fc wasn’t getting any input from me but then all of a sudden I got control back and managed to recover. I do this for freestyle because my feeling is the quad isn’t going to fly off too far in one second but it’s a lifetime when you feel that loss of control 😂

[@axelbrendel4091]

Thank you. You have, as usual, been very helpful. Keep up the great work. Cheers from Aus.

[@kennantvorskov5334]

Very good explanation for normal humans. As an airplane eng. I know exactly how difficult it is to explain. You closing worth's are LAW.... SHIT HAPPENS. Love it keep up the good work

[@lxsswxrds249]

Дуже чекаю на наступні відео по мілелрс,дуже багато функцій котрі через інструкції у пдф форматі не так легко розуміються як через Ващі відео, дякую

[@divingfalconfpv4602]

on my drone xm receiver the LQ was working accurately. Slowly went down while yes jumping around a lil.. My other drone R-XSR stays at 9 like the whole way then it all of a sudden drop to 4 then back to 9 then back to 6 then 9.. but seems to stay at 9 then numbers drop when it is close to getting RXLoss

[@RosscoStixFpV]

Hi I have a question, I just set up express lrs and tuned on LQ and rssi dBm the LQ flashes at 0 , and rssi dBm doesn't move from -130 how do I get these displaying the correct values? Tia

[@paulg5437]

I often get a loss of RSSI when the transmitter is too close to the receiver (~1 meter). Is this due to saturation of Signal, SNR or quality. I ask, as when it happens I'm usually trying to adjust something on the plane so I can't get too far away (unless I learn to operate the controls with my feet ;-)

[@GBoniFPV]

Great videos; I learn something today.

[@terminsane]

"i'm Paweł Spychalski and i'm going to engineer something today"

[@gabrielnunes159]

I have an ELRS Lite (2.4GHz) Wich has ceramic antenna and a jumper T-Lite with 100mw power and 50Hz frequency. I am reaching maximum 100 METERS before I lost signal. I am using in an open field with some trees, not more than 2 imas obstacles sometimes. Is something wrong? I tried a lot of things, saw a lot of videos about range but I can't get any better! Is this the real maximum for my config? Please help! I saw the conector, the wires, everything is fine! Thanks in advance!!

[@kkam7044]

Thanks, very informative, well explained

[@RobertCostarelli]

Are you able to get a link quality read out in the OSD on a R9 system or XM+ or it that only for crossfire? thanks!

[@nikotttin]

Good point! Last Sunday my quad dropped although the received signal strength was in the 60ies... I had the low signal link blinking on and off but never thought of it, since using an xm+!!

[@scissorzz]

I have a Tango 2 In my fatshark goggles I get LQ 0:0 flashing. Why? Checked the immortal T by changing it and still have the same issue.

[@TheFasteeve]

hello I have r9 mm ota and r9mlp ... while I was flying the radio it tells me no telemetry .... from that moment I no longer have telemetry on the radio ... how is it possible?

[@olivierf.4931]

Ok but if my RSSI is at 20 , can I be certain that I will be out of range in a very short distance in the same direction?

[@madladdan]

My lq drops from 2:99 to 1:100 after 200m in an open field with micro tx v2 on 250mw. Why does it drop so soon?

[@swimbeyonder]

Do you know why my drone always say rssi low and each time i fly i have to bind it again?

[@FPVUniversity]

Probably something is damaged, it should not behave like that. Happy flying!

[@kdeclinetostatendeclinetos6707]

Hi, I have older Futaba T8J radio with cheap Corona transmitter. I think I have found why failsafe is not working in my setup. It will go for all older receivers/radios. I can send You screen shoots so You can describe it in one of your video. How can I contact You?

[@VincentFischer]

Can't wait for the first receivers utilizing quantum entanglement. Then we couldn't only fly to the moon, we could fly through the universe with even better latency than CRSF :)

[@Hal-hq8fx]

Amazing idea

[@quaneu9216]

i think i broke my mobula 6😭 after a hard clash and clean up i plug in new battery，and heard small spark sound but everything looks fine voltage is ok video signal good osd display normally radio signal also great 8x signal but once i fly over a wall it just fail safe and say rxloss it just drop from sky with 4x signal of radio signal usually i can safely fly over there its just less than 5 meter away and if i fly around me very near, no wall, less than 5 meter everything work fine Is it something related Rx threshold to failsafe after several time of investigation, it almost fail safe every time it reach radio signal below 60 and just drop from sky (on the flight mode there it show 100 f5 101) not sure what it means have no idea what to do 🙏

[@BBFPV]

Where is LQ in inav?

[@h2o-fpv623]

Thank u for this good video.

[@dougmckay2387]

Thank you!

[@dylandickey3179]

I would very much like the ability to add LQ to the OSD in the next release of INAV. Looks like it was worked on here: github.com/atomiclama/inav/releases/tag/ls2 and github.com/iNavFlight/inav/pull/5098 so I'm hoping that it will make it in.

[@piotrkozlowski187]

Czemu nie nagrywasz w języku polskim?

[@rayang9929]

i know this video is a few years old, but my man, if your gonna talk about these subjects, atleast have betaflight open and explain how it relates to real settings you would adjist..

[@maelradec6766]

,,l,, engineer that