Thanks! Ordered mine, in route to me now. I went with the 507K mount because you can keep your front sight as a backup because the 507K has a rear iron sight built into it’s design.
@qb73847 ай бұрын
Would love to see that.
@Livie1033 жыл бұрын
Just received this site mount and I think it's great. Looks better in my opinion, I can pick up the dot quicker because I believe it presents better being lower to the bore. It was a little harder to get the old site off than I expected. Just had to get after it a little harder than I'm comfortable with but as soon as it moved it came right out. I saw somewhere, I think maybe in the post below saying to drive the old site out from left to right which is what I did. I went to our local ace hardware and get set screws to fill the holes left on top from removing the rail. Had a clerk trying to help me find the right size . Couldn't find the right size until I mentioned it was for a gun and he went to a screw section for guns and picked a prefect fit right out. Hope that helps someone else.
@JMJ3rd9 ай бұрын
Thanks for the tip of going to the hardware store for the filler screws. I will be there tomorrow to do the same!
@RenedeDon4 жыл бұрын
Super clean look and I love how the fitment is custom as opposed to a big plate that accommodates several models. I plan on ordering for my new Mark IV. Well done sir!
@JMJ3rd9 ай бұрын
I received mine today, and I have it installed already! I chose the RMR mount. I love the look of it, this way, instead of with the picatinny on top. The hardest part was removing the dovetail of the original rear sight. Sometimes, it does take a giant hammer! Thank you for this mod! I will boresight it here at home and take it to the range tomorrow.
@mikebaker32537 ай бұрын
Just got this today. Awesome piece of manufacturing. Makes the Vortex Venom have a great finished look. THANK YOU !!!!!
@karlp38404 жыл бұрын
Been using this for a year. Love this mod.
@mytquin76053 жыл бұрын
this mount is excellent. i like having the red dot as low as possible on my guns. your work is great sir !!
@denizenlocale34415 жыл бұрын
Just ordered one for my IV Lite. Wasn't liking the picatinny mount and necessary riser for the red dot. This is a very cool solution!
@danielbell78554 жыл бұрын
Just ordered one! Got the m4 2245 lite and venom. Cant wait for it to arrive! Good work man.
@aleistercrowley51674 жыл бұрын
Where from???
@feelingfeni47984 жыл бұрын
I just got the mount for the venom and it looks SOOO GOOOD.. : ) Thanks! Yea its sterdy and sleak and a strong mount as well.
@jomps11124 жыл бұрын
I got it it’s perfect fit and finish with vortex venom.
@izs19913 ай бұрын
Many years ago I bought this setup from you. I never could get it to stay tight. The first few times it came loose I snugged it back down and put a small amount of loctite. Eventually the tiny screws stripped and you were gracious enough to send some but I got frustrated and shelved it. Might be time to bring it back out and try again. I hate tiny Allen screws though. I did like how the low pro mount made the height over bore non-existent.
@ainaaipa8494 жыл бұрын
Great job! Nicely done 🤙🏾 Can’t find your link - just got me a Mark IV Lite -got a Vortex Venom on the way... I would like to purchase your set up to mount on my Mark IV
@mrkurleygunna5 жыл бұрын
Hmmmmm now you got me wanting to do this to mines smh. You a genius!
@Farrow_Tech5 жыл бұрын
Thanks!
@mytquin76053 жыл бұрын
excellent product. i will be ordering one as soon as i can get a ruger 22/45 lite.
@gremlin33624 жыл бұрын
Will be getting this as soon as the wife approves my requests... lol
@JoeHeine10 ай бұрын
Well done. I have a mark II and want a red dot to practice with.
@edbratt49554 жыл бұрын
had to sand on the dovetail insert to get it to slide in without a hammer. Holes were off center so if you installed backward the upper receiver would not go back on because the plastic mount very slightly covered part of the hole in the lower half of the mark 4. Finally got it together. Think I may order this www.kkdepot.com/Product.asp?Key=1528
@ConTheDon1872 жыл бұрын
looks a helluva lot nicer being machined
@landonlehman5497 Жыл бұрын
I got this mount and installed a holosun 407c on my 22/45 mkiv. I had to max the "up" elevation adjustment all the way to the top to hit on target. It did zero, but it wouldn't go any higher.
@LupusMechanicus5 жыл бұрын
Super clean, nice look there guy.
@Farrow_Tech5 жыл бұрын
Thanks bro
@Farrow_Tech5 жыл бұрын
Thanks bro
@chrissewell16085 жыл бұрын
Great job! Looks sweet, and I like the way it conforms to the slide. Can you make one, for any another pistol?
@Farrow_Tech5 жыл бұрын
Yes, this concept works well with most anything that has a dovetail.
@E.Chang.5 жыл бұрын
Awesome solution! If I want to remove my factory rear sight, can I just punch it out? Or do I have to disassemble the rear sight, and then punch the base out?
@dyoel1824 жыл бұрын
If it's an adjustable sight, you'll take the visible top screw out and then it will tap out left to right.
@nation8455 жыл бұрын
Love this, looks great. Will the screw holes that held the rail on remain empty or can you flush the screws back in without the rail? I assume they would be too long?
@Farrow_Tech5 жыл бұрын
You'll need some set screws, the original ones will be too long.
@ejharbord59668 ай бұрын
just got your plate and will try it and give my opinion. I am optimistic
@Wingman77tws4 жыл бұрын
well... thats what I need! ordered.
@bestleesinna77024 ай бұрын
Yeah...but if you're shooting suppressed and you see increased debris from blowback...will that not just sling it all over your RDS? Wouldn't it be better to position the RDS directly above the ejection port, so neither part of the lens is exposed to the blowback?
@julianw10892 жыл бұрын
Hello, can you provide a torque setting for the screws? I handtightened the screws but they came loose on the range so I am not sure how much torque to apply.
@free.range.engraving52455 жыл бұрын
Love that upper how do I find one for my mark2
@ronnydewailly70453 жыл бұрын
I need one of these for the delta point pro.👍
@thomasosborne73553 жыл бұрын
Does blow back from ejection get on the glass?
@TheNuclearBolton3 жыл бұрын
Any discounted pricing? 😂 The Ruger Mark IV lite is my dream gun and I’m going to be rigging it with everything under the sun.
@Serjanttt4 жыл бұрын
Good mount recommend
@mytquin76053 жыл бұрын
ordered one today !!!
@landonlehman5497 Жыл бұрын
Guy in a garage... you just cost me $350! Lol. I saw your mount and decided to buy it and a holosun 407c-gr-x2
@landsail3 жыл бұрын
Will any of your Mark II mounting plates work on any of the Crimson Trace Red Dots, especially the CTS-1550 model?
@jeremiahcaron83223 жыл бұрын
Wish you made them for a s&w 648.
@drachwitz5 жыл бұрын
Looks very clean. How about Vortex red dot fitments?
@Farrow_Tech5 жыл бұрын
Vortex and Fast Fire should be compatible.
@garybolick20973 жыл бұрын
I am beginner on this type of project, but will this system work on a Ruger Mark 2 Bull Barrell and what do I need exactly from the base plate to the red dot. (Not looking to spend a lot of money if possible) Is there a particular type of red dot that only works with what type of base plate. I guess I remove the iron rear sight and then dove tail? So what replaces the existing dove tail piece? I am afraid to take mine apart if this will not work on my gun. Help me please.
@mitchpeil17753 жыл бұрын
That mount is awesome. Will it fit my MK IV target??
@Farrow_Tech3 жыл бұрын
It will
@DismalTide5 жыл бұрын
Nice hob!
@ConTheDon1872 жыл бұрын
best way to get the old sight out? Mine is extremely tight
@denizenlocale34414 жыл бұрын
Here is how it turned out. Sooo much better than the last sight/mount photos.google.com/photo/AF1QipOjIpzQCwoMunGaSM5aHGzBV-spn2s3FcZIRVv5
@rdrun516604 жыл бұрын
Do you have a good torque value for the screws with your sight and a vortex venom? They constantly backed out and I finally got to 15 ft lbs and stripped it out. I just ordered another. I really like your sight mount, but the small aluminum spacers also came out of the base plate. I might go to a machine shop and make the wedge plate out of stainless steel.
@Farrow_Tech4 жыл бұрын
Bill, please email me with your order numbers, this should not be happening. I’ll refund your second order. Flood@farrow.tech
@rdrun516604 жыл бұрын
Guy in a garage it is ok, I think I probably pushed it too hard to get it solid. I just mounted the second one with a Holosun and it feels much more stable. No need for a refund.
@montanaplease Жыл бұрын
Suppose to go inch pound not foot pounds😂
@thrivivaladventures4569 Жыл бұрын
Will it work on TacSol Lite uppers?
@MrZola12343 ай бұрын
So, with the RMR mount, I can put a holosun 507comp on a mark 3????
@Farrow_Tech3 ай бұрын
Yes
@vicentehall6449 Жыл бұрын
Whats the inch pound torque spec for the base screws?
@larrycastro2303 Жыл бұрын
What size screws are you using?
@jessdyba5 жыл бұрын
Looks great. Are you selling these? I have Ruger Mark iv hunter and want to mount holosun 507c (Trijicon RMR footprint)
@Farrow_Tech5 жыл бұрын
Yes, Farrow.tech
@jefffogle9154 жыл бұрын
I have older mark 2 with bull barrel. And poly lower.. Wife has trouble with sights.. Would this also fit mine? Any info would be great
@Farrow_Tech4 жыл бұрын
Yes, this should fit.
@gregorymcclure6130 Жыл бұрын
How do I get this from you.
@Daddy537512 жыл бұрын
Don’t offer one for the Mark I. What’s the difference between the two?
@Farrow_Tech2 жыл бұрын
This will fit mk1-4
@Serjanttt4 жыл бұрын
it will work for holosun writhe?
@Farrow_Tech4 жыл бұрын
Yeah
@7892954 жыл бұрын
Is your mount any lower than the Burris mount? Just as durable?
@Farrow_Tech4 жыл бұрын
Yes this is very low, 0.050” between the receiver and the optic. We haven’t had any break.
@AnontheGOAT4 жыл бұрын
Is this the thinnest mount on the market?
@Farrow_Tech4 жыл бұрын
Yes I believe so.
@kyriakosmoforis59984 жыл бұрын
I want this mount for my Ruger how can I get one
@Farrow_Tech4 жыл бұрын
farrow.tech
@earnestsmith96963 жыл бұрын
You have the fitment for the RMR. Can I order the same for the SRO? Is it a different fitment?