Rust vs Muriatic Acid ***DISASTER*** Do not do this

Rust removal with Muriatic Acid is effective and effortless. Avoid the mistake I did, avoid the disaster! I used muratic acid from Ro-Tyme. Commercial Grade 20º Baume (31.45%).

[@dianeluke1746]

I really like how you edited your video to keep everything in, including your original happy ending, before showing us the disaster. Lots of people would have taken out their “mistake” and just made this a “how to” video. Instead you keep it real. 👍

[@circusitch]

Diane, you are 100% right.

[@gilesjackson9996]

Anyone reading this , dry immediately after washing the parts clean of acid, then dry again with a hair dryer or blow lamp to eliminate ALL water from crevices, buff with clean rag and IMMEDIATLEY oil or paint otherwise as others have said parts will flash rust in minutes

[@delatroy]

Any advice on how to do this on larger items like a farm barn walls and roof?

[@michaelpaciello7669]

@@delatroy don’t do that with muriatic acid at all. It’s highly corrosive, gives off dangerous fumes and can’t be healthy for whatever you plan to keep in that barn.

[@rocki_bb]

@@michaelpaciello7669 while the appropriate safety precautions need to be taken while using anything corrosive, the fumes do not linger in the way you're assuming. The barn would not become contaminated because muriatic acid was used, but it's not best option for that type of job imo. Using a pressure washer to remove the rust, replacing any rusty screws, treating the entire surface with a rust inhibiting primer, then painting would be better for a barn.

[@charlesfriend9557]

@@delatroy DON"T!

[@janettebuba126]

@@delatroy We used to paint large metal structures like water towers and bridges. Most paint was sandblasted and sometimes chemicaly stripped. \Never I mean never strip more surface area than you can prime seal the same day. Microscopic surface rust sets in almost immediatel it may not even be visible. The next day do another section and prime what you stripped. Once all areas are primed you can sand clean and topcoat. If you don't do this you will have rust immediately starting under the new paint job.

[@slprcel]

Be sure to neutralize the acid, with Sodium bicarbonate (baking soda) or Amonia. Then, immediately coat the bare metal surface with a protective barrier like oil, or primer if you plan to paint it.

[@roger55es]

If you want to electro plate it with nickle how would this be done ? Thanks

[@ch47av8r]

Very useful information regarding the impact on metal items from just the fumes from rags containing Muratic acid. I also learned this the hard way after placing a tightly sealed one gallon jug of muratic acid in a metal cabinet only to open it a week later to find a rusty interior of the cabinet and rust on the power tools stored inside.

[@Mdgreenlee]

Like Carl gangl said, you need to OIL everything to keep it from rusting. that's why manufacturers will often have everything covered in oil when you get it. My lathe requires oil regularly to protect against rust

[@jomamabee2481]

It is called flash rust. After acid prep, steel must be painted immediately, like within 15-30 minutes, or oiled.

[@mauri4763]

Thanks for the good video. A few comments. Acid + base = salt + water. The natural antidote to (muriatic acid) hydrochloric acid is sodium hydroxide (lye). Muriatic acid + lye = table salt + water. Water does not neutralize, only dilutes. Hydrogen chloride vapors irritate the respiratory system and corrode everything nearby in seconds! In industry, the process is: after degreasing, rust removal with hydrochloric acid and then immediately rinse thoroughly. If the intention is to elektroplate, there is no need to neutralize, because the elektroplating continues in the acid. But if the intention is to paint, you must immediately neutralize with alkali (NaOH) and then rinse with plenty of water and dry with hot air. Inorganic acids produce interesting results. If you neutralize acetic acid with calcium carbonate (washing soda), you get calcium acetate Ca(C2H3O2)2. When heated, it decomposes into acetone and calcium carbonate.

[@spudth]

Here's a little story. I once was etching a concrete floor with acid at work. I left the unsealed acid container in my work truck. It fell over and leaked a small amount on tge floor. My work truck was closed and locked for several days while I was on vacation. When I returned there was literally a cloud in my truck when I opened the door. The acid caused slight corrosion on all the bare metal inside the cab of this truck. As for this guy. Wash the part in baking soda before drying. Dispose of the acid laden rags. Hermetically seal any containers having acid. If you have bare metal it's a good idea to coat it so it does not rust if a period of time passes before it will be painted or have other metal conditioning.

[@bfgoalie99]

yeah and leave the shed door open! those acid vapors will rust everything in sight to bits given time.

[@chefstilwell8730]

never try to neutralize and acid with water!!! always use a base such as baking soda, and pouring warm water into acid is a terrible idea

[@ProCleanPW]

All the instructions I’ve read for oxalic acid say to mix it with warm water. What am I missing?

[@williamevans6522]

Using muriatic- not oxalic. Always pour acid into water- never the other way around.

[@ProCleanPW]

@@williamevans6522 so is it just oxalic that requires warm water? Muriatic, hydrochloride, they don’t need warm water?

[@williamevans6522]

@@ProCleanPW In general, chemical reactions speed up with increasing temperature.

[@gilbertcox5075]

I didn't see safety glasses I am interested in buying your =

[@lulop022882]

Great video on the using the m. Acid. Electrolysis still produces hydrogen gas which is very very flammable. What I liked about the m. Acid, the process was really quick. I can’t see myself waiting hours on the electrolysis or the vinegar to work. I’ll spend the extra time on safely using the m.acid 👍🏻

[@eugenegreenin1903]

Informative video on how to do it and what to watch out for. Thanks for the knowledge. Keep making videos.

[@r2db]

You mentioned breathing the fumes and the need to use a mask. What you need is an acid gas rated respirator, or preferably such a respirator and adequate ventilation. Also, removing rust by this method might be problematic for the spring as it can make the steel more brittle. The rest of the parts are thick enough that hydrogen embrittlement of the surface is unlikely to be a serious issue. It is nice to see proper buttress threads on the screw, which is a detail often missed for parts today. It is a stronger thread profile in one direction, so it is used in that case in the direction that the screw is tightened.

[@josephlieberman3027]

i used acid to clean some old machinist calipers and dividers, the results were the spring steel piece where the legs squeeze on a pinion the spring just fell into two pieces.

[@SuperSisterPrincess]

HI. When you wash your part, did you use a water pressure washer to cleaned deep any acid ? Also, before painting, I highly recommend to paint with zinc (spray can or using a gun LPLV) to repel any humidity and protect against rust.

[@nickmccarty6249]

Flash rust is a thing, but note how the part that wasn't in the acid didn't rust? Yeah, water alone won't neutralize the acid, use a baking soda water mix, then rinse with plain water after. I made that mistake before, it's a learning process. Love how you had the success and failure together. So many fake people would have edited out the mistake, respect.

[@Quinteros777]

Yeah, I learnt the hard way too. Thanks for watching.

[@mickestahl6178]

Acid cleaned steel will flash rust very quick so the second you have neutralize it you need to spry the parts with some oil type WD40, or if you are supposed to paint it just do a quick base cote with primer.

[@rikityrik]

Is it necessary to rub baking soda water on parts to neutralize or can you just immediately dry and spray with primer. I’m getting contradicting info. Thanks.

[@beenheredoneit.4381]

You need to neutralize it before you do anything else.

[@rikityrik]

@@beenheredoneit.4381 thanks! Can that be done by way of a spray bottle with baking soda/ water mixture? Or does the part need submerged/ soaked in baking soda water?

[@DoctorMangler]

Hey thank you for the video, I hope you keep making them!

[@analyst8258]

Can we use muriatic acid to remove rust from galvanised metal roof sheets?

[@josephlieberman3027]

im not a chemist, yet it was explained to me that with acid less or diluted can work very well, full strength acid the molecules are like having to many cooks in one kitchen they impede each others activity, the acid reacts with the metal along with water, now if you want shake a little table salt into it also it can help

[@KevinNguyen-zn4vv]

You can buy a gallon for around 12 bucks at home depot with a ~30% concentration. No need to dilute and it's safer to handle. $1.25 ammonia at dollar tree to neutralize it and lots of cheap scrubbers and containers.

[@rvscootin3457]

Out Gassing of the acid will settle on EVERYTHING!!! Glad it worked out in the end.

[@WilliamVG]

Muriatic acid is very potent stuff, water alone is not enough to netralize the acid. You'll need a mixure of baking soda and water afterwards but even then there's a chance the metal will flash rust and continue go brown afterwards.

[@adrianrouse5148]

Agree baking powder and dry and oil or paint as fast as possible.

[@kellyjones841]

​@@adrianrouse5148yes I agree. From my experience, do not use indoors, lathe bed, drill press, some tools will turn brown and start to rust. I have done body parts by putting a mechanic cloth on panel, then pour or brush acid on. When cloth turns brown, remove. Repeat as necessary. Neutralize with baking soda, dry and paint immediately

[@lewisbrodnax7898]

What about hot blueing? If you heat t metal to@ 650-700% then drop(gently!) Into linseed oil it will be black oxide coated

[@picklesnoutpenobscott3165]

Good advice to me, do not leave it in the garage to work, use it in warmer weather. I was aware of the neutalization required of all acids, even vinegar. Just to be safe I will store the container out of doors. I will use my respirator for sure as well. Cherish your most important tool, your well working body!

[@twizz420]

"the best way to neutralize it is with water" ABSOLUTELY WRONG IN EVERY WAY

[@angelicamichelle1646]

So after I use water but I see it try to get crudd again

[@kevinbirchall2758]

Neutralize an acid with a basic material (common material: baking soda, for example)

[@astaghfirullahalzimastaghf3648]

Lolapathy It's so funny

[@jwillk9438]

@@kevinbirchall2758 water and baking soda then?

[@kevinbirchall2758]

@@jwillk9438 Sodium bicarbonate alone would do, adding water may be easier to mix in best

[@liquiddreamification]

It may be a bit redundant, but I think I would pull the parts out. Neutralize them in baking soda and water. Before I did any kind of brushing at all, when dealing with acid. You can always throw them back in if they are not done.

[@10mmfan]

Neutralize with baking soda solution, let dry but quickly oil, paint or spray a coat of clear on it. They will stay shiny! Been there done that. Always wear a 3M respirator with filters. Been there done that.

[@delatroy]

Thanks. I want to remove rust on an old farm shed. I want to use the acid but I’m worried that it will seep into the soil and make it toxic. How can I be safe or is there another way?

[@josealejandromartinezlopez3924]

Do you ads baking soda to a bucket of water?

[@penibeni1085]

@@josealejandromartinezlopez3924 You add the baking soda to the container the acid is in. If its a small container, pour it in a bigger one with alot of water. Baking soda & acid causes kind of a volcano of fizz & fumes. Best to do it outside.

[@penibeni1085]

Best to do everything outside. Those fumes are going to rust everything in your shed.

[@4jimcollins]

@@josealejandromartinezlopez3924 Have a separate bucket ready with a solution of baking soda and water to neutralize the acid on the part you are cleaning.

[@sharpeyedwatcher9724]

I can tell you what went wrong! You should have coated the newly derusted parts with a light oil like WD40 to avoid the flash rusting that happened overnight. It would have still ocurred even without the remnants of rubbish left in the rubbish bag.

[@TheChrisey]

That depends a lot on the humidity. The main thing that happened here is that he did not actually neutralize the acid. Cleaning it in water is not going to remove the acid. Then, if the humidity is fairly high, it needs coating, oil or phosphoric acid or a primer. If it's not that humid (like winter/spring conditions) then it's not going to flashrust. Ofc it's also important to completely dry the parts, a towel or cloth is usually not enough so it should be dried with hot air or a torch.

[@johngalt97]

@@TheChrisey I've used a product called PHIX: Spray, brush, or soak to 1) totally dissolve the rust, 2) etch and zinc plate the cleaned metal surface, and 3) phosphate coat the zinc, leaving the surface totally prepped and ready to paint, oil, or polish. It seems to avoid the flash rust.

[@melfrank8379]

This guy took too many risks moving containers and using it inside also strings to pull out the parts. What went wrong is after you rinse make a solution of water and baking soda and neutralize the acid on the parts by dipping them, have a second bucket of baking soda and water to do a final dip. Then when you have the parts clean and dry use a oil base enamel paint, or clean the parts with acetone or lacquer and prime them immediately for painting. Then you are good to stop the rust from returning. Most important be careful, this stuff is dangerous to breathe, wear the appropriate mask and eve protection with gloves.

[@rolldogg01]

This is the best advice on this process!!!!!

[@johnr4898]

Freshly cleaned metal will rust start rusting immediately in the air as well (the acid vapors also) you need to paint or oil the parts to keep the air away.

[@anandkr6035]

The problem is not disposing the left item. The problem is when those things after it gets treated with muriatic acid come in contact with air , oxygen it corrodes.

[@johnhall8455]

Sodium Bicarbonate (baking soda) will neutralise the acid as already mentioned, but what I did notice was that the black plastic bag was covered in water droplets..With the cold temperatures do you have a problem with condensation?…Uninsulated sheds and garages suffer really badly in winter, especially the ones with metal roofs, to the point where they are dripping with water..Temperature plays a massive part when doing this kind of work..

[@jaymorris3468]

Best way to learn, but infuriating, but thank you for posting and warning us. 👍

[@MeowThingy]

You put enough of that powder to bring down the PH in an entire 15,000 gallon pool into a 5 gallon bucket.

[@Mr._Lister_The_Sister_Phister]

Hey man, it's all good. I know you feel like you wasted some time, and its never fun to have to deal with unexpected problems, but it wasn't wasted. It was probably the best spent time in the whole ordeal. Afterall, for the majority of the video, youre doing exactly what you intend to do, nothing more nothing less. However the part where you're de-rusting it for the second time and feeling that disappointment...just think of that little bit of disappointment/inconvenience as the small price to pay for the confidence of knowing that you'll never make that same mistake again.

[@Quinteros777]

Thanks for watching and thanks for the encouraging words!

[@beezwelliver4806]

muriatic acid leaves an oxide layer behind and will keep eating metal use baking soda water. i use muriatic to copper plate and sometime with electrolysis (use graphite for anode)

[@figbat6363]

Put some in a spray bottle,spray it on the rust.scrub it with a soft bristle brush.than rinse off throughly

[@facereader99]

i used pure acid. The parts were clean in 20 minutes. I washed them with water, and dried them with a clean cloth. I saw the beginning of rust, very faint rust. I laid an open carton, and immediately painted all. A week later I looked. Wherever paint had not reached, was rusted again. So, back to the acid soon, wash with water, and hang objects on metal wire to see all nooks and crannies, then paint again. Oh, the smell of acid or by product of acid eating the rust - I got a brief but really nasty hit. Seems to burn through my nose tissue. Will never forget it. Nobody will.

[@notme9184]

To neutralize use baking soda.

[@skynetkage3377]

You should put some oil after you clean those steel so that moisture cant affect the steel.

[@jackyeferreira5039]

I need to remove heavy rust from steel base columns . So if I understand. 1. MIX 1 cup acid + 1 cup water with baking soda. 2. Spray 3. Rinse with water 4. Dry really good and 5. W40 or primer. I am right? Thanks

[@dijohnson7]

As soon as I saw them after they had got the rust back I thought he didn't neutralise them, should have used some baking soda!

[@chrissybabe8568]

Or hydrochloric acid if you want the more accurate chemical name. Muriatic acid is an old fashioned term meaning "pertaining to brine or salt" (Wikipedia) which really has little to do with its modern production. A term used more for historic reasons than anything else. Sometimes also called Spirits of salts. If you walk into a hardware shop here to buy Muriatic Acid they will look at you blankly. I suspect that Muriatic Acid usage in the US is a bit like Imperial v metric. Sometimes the US has a bit of difficulty keeping up with the times.

[@Patrick.Sanchez]

Is this an unofficial Breaking Bad - Season 6 trailer?

[@martehoudesheldt5885]

when you acid bath the metal it strips it bare. in that it will rust instantly! take it out of the acid and neutralize in baking soda, dry and either paint or coat in oil to keep it from rusting again rapidly.

[@andypdq]

Anyone who knows at least a bit of chemistry would know, remove items from the HCl, wash with water, neutralise in an alkaline solution of sodium bicarbonate, rinse again, then oil or paint.

[@mr.cryptobull1520]

After removing rust, I rinse with water, then a baking water solution, If I'm going to paint it? I rinse with HOLDTIGHT solution ( stops flash rusting for about a day). If I'm not going to paint, I final rinse with WD-40, I also ruined some metal in my shop just from the fumes the first time I used it, USE ONLY OUTSIDE!

[@eugeniujosanu279]

I found out if you wash/soak it in the gasoline right after taking out from the muriatic acid. all the left over acid from the rusted product will end up at the bottom of the bucket since it s heaviest comparing to petrol (gasoling) . Take it out , gasoline will evaporate and you ll end up with clean product ..paint over or buff it .

[@williamemerson1799]

A couple more options are electrolysis and/or warm vinegar with salt added. Keep an eye on small parts when using the vinegar method. I ruined a small auger bit by leaving it in the solution too long. Chlorine will cause you the same problems when left open around tools and such. 👍🍻

[@domecrack]

There's also evaporust, that stuff works really well

[@williamemerson1799]

@@domecrack Yeah, there's a guy that has a YT channel that seems to use that stuff exclusively when restoring tools. 👍🍻

[@domecrack]

@@williamemerson1799 I use it myself all the time. Stuff is phenomenal.

[@williamemerson1799]

@@domecrack Good to know.. Haven't tried it yet.........mostly cause I'm a cheap slug.🥴

[@dream0darkness013]

This deserves more likes truth be told

[@pourtierbeatz7804]

What if i dipped head cam cap bolts dipped them in acid then wiped with a cloth and drenched in oil and installed ?

[@Gutslinger]

Next time, I'd just do one piece with each test. That way you don't have to waste a lot of labor if it doesn't work out.

[@Dennis-uc2gm]

I had a neighbor with a gallon of muratic acid that had a pin hole leak onto a wood bench and didn't know it. It ate a hole in the bench and the fumes caused any fine steel that was nearby to rust in a matter of a couple weeks. Almost a disaster. It's thought me to even bag the jug with some heavy plastic if I store it. I pretty much use the Evaporust now, fairly safe even though it takes a little more time. 👍

[@Quinteros777]

Where I bought from, they had it wrapped in a thick thick THICK plastic bag. This chemical must be kept out side! Away from any kids! I don’t use this product anymore. It’s a great product but too dangerous.

[@Dennis-uc2gm]

@@Quinteros777 Yeah, I keep mine at the end of the garage by the door in a thick plastic bag also. ANY leak can be a disaster. If the stuff wasn't handy to have once and while I would just buy and discard. The good thing is no kids around anymore and ifthat were the case I'd just not keep it around at all. Seeing first hand what just the fumes can do convinced me the stuff is dangerous like a lot of acids.

[@JohnLeaf]

thanks my friend you helped me a lot

[@Quinteros777]

Welcome Bud! Thanks for watching.

[@justinperry2392]

What if the metal is soaked in diesel? Will it flash?

[@damo690]

You need to neutralize the acid with bread soda and water. Wash your parts in bread soda and water, wash your bucket in water and bread soda

[@saleemkader2126]

I dont know if after polishing them dry then wipe them with an oily rag. or spray wd40

[@hobbyautobodyfun9315]

Baking soda it actually if you have Heart burn also works too .

[@circusitch]

Sodium bicarbonate (baking soda) or ammonia can neutralize the acid. Water only dilutes it.

[@jamesramos1200]

Vent thatshed man. I realized how dangerous this is. I need high vent outside the shed so that it does play on nextdoor neighbors kids.

[@aaahtex902]

**HARDLY A DISASTER = I'M GONNA TRY IT!!!**

[@MrOner07]

you deserve more subs for telling the truth... i dont know what happened but im guessing its the water that you rinsed the parts with...

[@sonicdewd]

Three things: 1) Neutralize the acid on the iron by putting them in a baking soda or drain unclogger + water solution for a few minutes, or scrub them down with oven cleaner (fume type). Then soap wash. This will prevent rust flash, and also the rust won't develop under any paint you might use. (Water alone does not neutralize anything.) 2)) Don't acid-bath springs!!! This will cause a change in the metallurgy and also cause stress concentrations. Just buff them off. 3) Those plastics like what the bucket is made of don't get affected by Muriatic acid. However, some plastics disintegrate in short order. Best to keep this in mind.

[@Quinteros777]

Thanks for the tips. I will be more careful next time knowing this. Unfortunately I had to learn the hard way. Thanks for watching!

[@Hydrogenblonde]

After you clean parts in acid, immediately rinse in hot water, then wash in hot water and detergent and scrub vigorously. Rinse again in hot water and dry in a oven. Get the parts good and hot to evaporate any water and it will also evaporate any traces of acid that may have soaked into the castings. After cooling paint immediately or oil parts that require lubrication. The acid is both your friend and your enemy. It can make impossible cleaning easy but you have to work very fast to eliminate it or the parts will rust worse than ever.

[@Quinteros777]

Agreed, a friend and an enemy!

[@nomar5158]

flash rust,just dip it again and seal immediately after wash and dry!!!and yup the fumes will rust all in the area...

[@ESLinsider]

So can anybody share the disaster? or where it is in this video.

[@ST-IV_858]

U need to oil the metal after wiring. Because it is raw steel which will need to be washed in baking soda after acid

[@rossokeefe9268]

Where did you buy the muriatic acid...would it be the same as stuff used in pools?

[@Quinteros777]

Bought acid at Canadian Tire. I googled places to buy. Read comments below, I think I replied to a comment with acid percentage I used. Not sure if pool stuff is strong enough.

[@grassroots9304]

Those fumes are insidious. 1 gal jug, 41%, lid on tight: inside 48' x 60' shop w 20' walls (large interior volume) all my stuff was rusting. Lid was not fully sealing despite being tight. Put it outdoors and solved the problem.

[@charango_it]

What is the concentration of hydrochloric acid in your muriatic acid?

[@Quinteros777]

31.45%

[@glupilazni1399]

The easiest way to neutralize any acid is to drip it into baking soda solution.

[@mbahismu4156]

You better to use phosphoric acid. It won't clean rust as muriatic acid did, but it turns rust and bare steel surface to black coating that prevents further rust. Similar to the way aluminum "rust" protects layer under it. You don't event have to neutralize exces acid. Just let it dry.

[@romankuprava1346]

Soak parts in soapy water , then polish, then oil or paint it asap.

[@Ernest_More]

It’s flash rusting. Could you simply oil the parts after?

[@freeaudiobooks7469]

I think so

[@CountChokcula]

Yes, oil is highly recommended, or electroplating, or galvanizing, or if it's mild steel you can apply a black oxide coating

[@douglasthompson2740]

It is best to neutralize with baking soda in the water. Plain water would have to be changed a few times with long soaks. This would most likely reflash your rust. Baking soda neutralizes the acid in all the nooks and crannies very quickly so a ten minute soak in warm water with soda will be very effective. Then one rinse in pure water and quickly drying the items seems to work the best. After wire wheeling wipe them off and coat with an oil. I like to heat them to three or four hundred degrees and then quench in oil.

[@rudysmachado5747]

Good advice. What’s the strategy of heating to such high temps at end… is it to dry it?!

[@douglasthompson2740]

@@rudysmachado5747 dry it as well as allow the metal to draw the oil into the steel while forming a strong coating

[@douglasthompson2740]

PS: you do not want any moisture under any type of coating for the most part.

[@douglasthompson2740]

PPS: Also gets rid of the moisture quickly and thoroughly. Longer it sits on or in the metal the more oxidizing occurs. Lots of O2 in water able to combine with the metal for rust, much more than air.

[@Snail2G]

The rust didn't come from the acid whatsoever. This happens when you get metal down to a bare surface and leave it exposed to moisture. It's the same reason your brake discs will get a coat of orange surface rust overnight if it's raining. Bare metal parts need to be covered in either paint or oil almost immediately after cleaning.

[@nwatson622]

Once you crack the seal the fumes still are able to escape an flash rust your work

[@chrismoltisanti2763]

I don't think it was the acid fumes. I think it was just moisture in the air flash rusting the freshly etched metal. You got fresh acid etched bare steel. Any bit moisture is gonna make it rust right away.

[@diycarhome9151]

Used Muriatic Acid for 25 years. Safety first. Use full strength or 50/50 water based. If soaking at full strength it has to monitored. Will eat the part. I usually will brush acid on non precision car parts. If the part had ground or machine surfaces use sparingly. Or use cleaning vinegar. Some parts I full on full strength. Trailer axle, trailer springs, lawn mower deck, snowblower housing, car rims. Parts of machine finish to use a lighter acid to clean. Crankshaft on lawnmower or snowblower.can put electrical tape on ground finishes and do the counterweights with Muriatic. Always be careful. Bottom line.

[@hunniebe6]

Soak the parts in baking soda solution, rinse, dry and coat with oil or paint.

[@hankhessig6586]

thank you so much for sharing your lessons learned

[@bjodaddyo]

Know I know the meaning of "Rust Never Sleeps."

[@neeliekirsch9072]

My friend ~ IMPORTANT! Water alone does NOT neutralize muriatic acid! You must add a fair amount of BAKING SODA to the water. Also, distilled water is preferable.

[@Aquahoma]

wipe it dry really good and spray wd 40 on it rub it in

[@RD-kz4wr]

Lol, dude wrapped a bucket with a heat mat. LMFAO

[@djrowe2]

Liked your good video presentation but you failed to oil your parts afterwards. Just plain old wd40 spray will protect or if in a pinch motor oil rubbed on.

[@djrowe2]

Plus forgot to mention 5 gallon bucket of water and 5 cups baking soda is neutralizing agent post acid dip.

[@robertfontaine3650]

Flash rust. didn't get all the acid off the part.

[@corail53]

Dilute the acid and have a means of neutralizing it afterwards.

[@k.tiwariartbadlapurtiwari9731]

Is that work for use to etching steel??

[@Quinteros777]

Yes but I would go with electro etching, less corrosive less toxic.

[@Good-Enuff-Garage]

yup that's muriatic acid for you, and that's why I only use Phosphoric acid, I painted a hood of my truck after stripping it with Muriatic acid, neutralized it with baking soda after and still it rusted in less then a year after being primered and painted, trust me it wasn't that you left those other items in the shed, Muriatic acid does not prevent rust, that's why hot rodders use it to build up fake rust patina, it will actually rust things

[@darylmorse]

Water DOES NOT neutralize acid. Only a base neutralizes acid,. You should have taken your parts from the acid, rinsed them in water and then put them into a base to completely neutralize the acid. You could skip the step of rinsing with water and go straight from acid to base. After that, you must protect the metal to prevent it from rusting.

[@edwardschmitt5710]

very helpful.

[@henrysmith8012]

I have been using it to derust parts for years or clean fuel tanks. It's no big deal.

[@waynepeterson8211]

What percentage is the muriatic acid? I bought some today (paint dept,) and it is 31% muriatic acid. Is the acid you're using 100% muriatic?

[@Quinteros777]

Hey Wayne. Muriatic I used was 31.45%. Stay safe!

[@waynepeterson8211]

@@Quinteros777 Thank you for the response. After I use the lantern, I'll let it cool. Then fill it with white gas to retard the rusting?

[@voidisyinyangvoidisyinyang885]

you flash rusted it from rinsing it in water

[@lovelyjanemendoza627]

you ddnt rinse with baking soda

[@grassroot011]

Coat all surfaces with oil as soon as water dried off the items.

[@mattrobinson5219]

I’ve been experimenting with stronger and stronger vinegar to get rid of rust off old tools. I think I’ve pushed it too far and the last batch I left in 20% strength industrial cleaning vinegar for a few weeks and now all the hardened steel is eaten away like a honeycomb effect. Does anyone know if they are ruined or is it salvageable with heavy grinding?

[@Quinteros777]

Hey Matt I would not grind the tools. This would further weaken the tools by removing material. Neutralize well with baking soda and water and apply some WD40. What I now use to remove rust is Evaporust. Very effective yet gentil on metal and not corrosive to humans. Expensive BUT you can re use it over and over again.

[@angelicamichelle1646]

O yeah it dose need a bit of oil only on parts .

[@Crawlerjamie]

Thanks

[@martinpetersen6266]

fastest result. heat it up till it nearly boils. reason for this is due to how chemicals work faster when the atoms collide more often, which is the effect of higher temperature. this is in relation to how far away from absolute zero the temperature is though so even at near freezing the acid will still work quite well. though not as well as when it is near boiling. minuscule difference when speaking about 20 degrees C.. so yea. sort of waste effort unless you are absolutely gung ho on saving a little bit of time. the way to really make the reaction faster is by concentration, meaning don't delude the solution too much. it is probably already deluded. !! Important Always Always Always, safety first. You can buy gas filters for that gas mask.

[@sohchx]

You neutralize muriatic with baking soda, then water

[@CSGATI]

You need to neutralize and OIL IT.

[@oompalumpus699]

Don't forget the butter.

[@litty1776]

Any specific type of oil?

[@litty1776]

 what kind of butter

[@jlaguilar369]

You got it right, you neutralize the acid with sodium carbonate and water then hit it with oil to prevent flash rust. When your ready for paint hit it with acetone to clean off the oil on the parts that are to be painted that simple.

[@jamessheehan1045]

@@litty1776 Unsalted....