Rx100/135 Removing The carburettor components for cleaning ||Quick Guide --Ep: 3

Hello viewers this is the third video of the carburetor series on my channel.
In this you'll learn the complete dismantling process of a mikuni series carburetor
watch this video and get through the process before messing with carburetor
Here we will see the complete process of dismantling the carburetor before cleaning it.
In this you'll find a complete procedure of removing each and every component from the carburetor and checking if they are good on not.
This will be followed by cleaning and assembly video and few other important technical aspect of the carburettor, so stay tuned and watch the full series with patience
REST ALL IS BELOW-
you can watch my videos from the link below :
MY YEZDI :-
1--- • YEZDI 1978 RESTORATION...
2) • YEZDI 250 RESTORED | A...
3) • Yezdi diaries,Forever ...
3) • YEZDI 250 EXHAUST SOUN...
Royal Enfield-
1) • Enfield 350+ FZ16!BROT...
2) • OLD MODEL BULLET 350,O...
3) • OLD BULLET 350 ON HIL... Link to my rajasthan Ride series
• Rajasthan Series
-----------------------
Link to TECHNICAL playlist 👍
• DIY/Motorcycle Works/ ...
----------------_---------------
Link to Yamaha Rx series bikes -🎂
• Yamaha Rx maintenance ...
music credits-
www.bensound.com
Rides -
• MOTORCYCLE RIDES
FOLLOW ME ON INSTAGRAM - moto_travelxd
MAIL ME AT - [e-mail]

[@MotoTravelRide]

This is the 3rd video of the carb series....🔧🔩 😔 Sorry for the Low audio levels. Recommended to use earphone.

[@vaibhavpatil86]

First like to your video 4 min from posting. 😊

[@MotoTravelRide]

This love means a lot brother 💐

[@brotherrider1718]

Aapki har ek video mein bahut different baat hoti hai nice. .

[@MotoTravelRide]

Thank you ji..

[@vijayam1]

Thank you. Where can we get the airscrew O ring?

[@sirajhussain791]

very informative and quick

[@debashismohanty4055]

Please put one assembling video also

[@ankushm6672]

Hi Waiting for your assembly video.

[@ankushm6672]

Can you please explain to assemble back the needle pin. Any specific tool reqd?

[@rajeshjena22]

Broo Rx 135 chain adjusting ka ek technical video banaiyee ...or ek request tha ki aap jab video upload kar rahe hain kab video ka thumbnail thoda alag Digiyee tabhi aap ka video jyada subscribe hoga or like badhega. Your explanation on RX is too good. I am waiting for your next video.

[@MotoTravelRide]

Thank you brother... Apke baat ko jarur dhyan me rakhunga.. thank you so much,i s advice ke liye . chain pe bhi video ayegi one by one.agar apko kuch personally puchna hai then instagram pe msg kr skty hn

[@rajeshjena22]

@@MotoTravelRide ok broo

[@arjunrana2724]

Bro oil mixture ko kitne round tune karna hoga

[@MotoTravelRide]

har bike ka alag hota hai. aur bahot sare factors hain jispe ye change ho jata hai -jaise, height, climate, air density, size of jets used,

[@dopdenic1180]

Hi bro this slider piston number which

[@shreyashshetye9654]

Sir please make a full detailed vedio on the carb, i mean ke explain, ye part kharab hua to kya prom atta hai bike me

[@MotoTravelRide]

Sure, at the end of carb series. Problem sorting video ajaega 😀 . Thankyou ,dont miss notification 🔔

[@akhilkumar-oh5zx]

Sir ji , I have Yamaha rx135 , mujhe carburettor kit chahiye , konsi company ki sabse acchi hoti h , kya original bhi aati h abhi ? Please reply sir ji 🙏🙏🙏🙏

[@nicrk6808]

Can we do spray paint ??

[@MotoTravelRide]

No.. please don't use any paints on carburettor

[@shamsu1003]

Sir My bike rx100 Top speed is only 90 km I changed clutch and steel plates. Carburator . Same problem remains New chain set of rxg I heard a stock rx100 can reach 100 to 110 speed I changed sproket from rxg 37teeth :-(Still same speed Please reply me solution For that.i use stock exhaust and flute I used 18 inch wheel to check top speed but no difference same 90km

[@MotoTravelRide]

Use rx100 chain sproket 39 ×15, . Tune carburetor properly.also inspect the reed valve. You'll get 100-110.

[@nelsonshoby5781]

Idle screw of my rxg is missing , is it possible to use rx100 idle screw in rxg

[@MotoTravelRide]

No,you can't. Use any 135 one's

[@nelsonshoby5781]

@@MotoTravelRideit's written as 4TL01 in my rxg carburetor. Is it the carburetor of rx 135 4 speed?

[@MotoTravelRide]

Rxg/rx135 have same carbs. Only difference is of the choke levr 01 has- pull type choke( as in rx100) 10has - wire choke.

[@nelsonshoby5781]

Thanks for replying, in Hindi review you told that idling screw of both rx100 and 135 are same that's why l asked whether its possible to use rx100 idle screw in rxg.

[@MotoTravelRide]

Hey..just re-read your thread. It was air screw in my mind, as usually people ask regarding swapping them. Sorry for that You can use 100 ideling screw on rx135.. or even rxg on 135. All are swappable( as said in video).

[@pearsonbraganca1765]

Need help..... Is there anything I could do/change if the throttle is slipping?

[@MotoTravelRide]

Couldn't get you... what exactly you mean by throttle is slipping?? Details

[@pearsonbraganca1765]

@@MotoTravelRide sorry my bad..... idle screw** anything can be done if the idle screw slips wen adjusting

[@pearsonbraganca1765]

Idling*

[@babagoats7083]

Bhai assembly Ka video dalo .. please

[@josco75]

How to set the carburator float height in an easy way?

[@MotoTravelRide]

there isn't an easy way to it, :) will put up a video to that in coming time. thankyou,stay tune to the channel

[@axegogoi]

Dear Sir, I have dismantled the Rx135 4speed curburretor as per your instruction. After cleaning and replacing of O rings I have re assembled the curburretor. Now, I could not adjust the air & fuel setting to idle speed. Kindly help us by providing an another valuable video on setting up of Rx 135 curburretor.

[@lnsanjib]

Sir first of all thanks for your valuable videos for Rx 100 and Rx 135 owner. Sir, do I relpace Rx 135 carburator with Rx 100 carburator. Waiting for your reply

[@MotoTravelRide]

Thanks you. No, don't replace 135 with a 100 carburetor.

[@lnsanjib]

Thank u sir,once again where do I find best Rx 135 carburator please help me .

[@MotoTravelRide]

At some old shops you may find, if lucky. Mikarb you may find.

[@lnsanjib]

Thanks for your suggestion, sir I found a mikarb but sir it is Rx100 carb and the sellar is saying that the fitting is same . Please help me in this regard.

[@MotoTravelRide]

@@lnsanjib not same, sellar is trying to fool you watch the video once again, have clearly said it brother

[@matttucker4269]

Bro can i used bottom part carburettor of rx135 in rx100? Will there be a problem like sound of the bike??

[@MotoTravelRide]

Yes yu can use.. no problem

[@matttucker4269]

@@MotoTravelRide thanks bro

[@matttucker4269]

@@MotoTravelRide bro.. how to paint engine cover like original? Some say painting engine cover is not good ..instead buffing is good? ... Help me out bro..

[@MotoTravelRide]

You can it done with heat resistant paint.. . Buffing is also good 👍 I'll try to make a detail on this.

[@matttucker4269]

Which paint bro?? Paint name? I used spray paint & it wash away like paper when in contact with petrol

[@kushgoliyan2908]

sir i have a problem in my rx 100 my bike sounds bad on low rpm and everything sounds good on high rpm everyone is misguiding me anyone saying its clutch bell problem anyone saying piston anyone saying crank

[@vaibhavpatil86]

What's the function of small ball like projection at the front side of the carburettor? (The side facing to the intake manifold hose)

[@MotoTravelRide]

Good question.. you've noticed it but missed few things. Check out, it is at several places on the carburettor. Find them where they are, you'll find the answer to why they are 🚀.😉

[@vaibhavpatil86]

@@MotoTravelRide sure brother.... waiting for them 🙂

[@vaibhavpatil86]

@@MotoTravelRide I tried to search on internet about it since i am in Canada now I couldn't check on my bike physically. I found them near petrol inlet pipe on carb, near the hole where pilot jet fits in, on the filter side tunnel where 2-3 holes lead to float bowl and then last on the choke body....i think they are just the part of brass housing bulging out looking like a ball but they are essentially the internal passages of brass materials embedded in the aluminium casting material on carburettor body....please correct me if wrong 🙂

[@MotoTravelRide]

@@vaibhavpatil86 ohh okay, you're almost there 😀. those plugs are used to seal the drilled holes from outside . It's a kind of plug. Wherever there is this plug ,we find a passage right in front of it on the inner side , or at some critical angle which can be only accessed by these holes. Once you get carb in hand you can observe more carefully, it's even on the autolube pump, big chrome ball.

[@vaibhavpatil86]

@@MotoTravelRide Thanks a lot brother...main soch soch ke and videos dekh dekh ke thak gaya tha ki what are those balls like thing...and yes there is big crome ball on 2T oil pump next to bleeding screw on it. Now my doubts are cleared about it 😊.... will definitely grab the spare carb of my RX once i am back home to do careful observations.

[@donvictor196]

❤️🤟