Kupiłem uszkodzoną gwoździarkę z zamiarem jej naprawienia. I have bought a broken nailer in order to fix it.
Пікірлер: 25
@NNITRED5 жыл бұрын
Very informative . Eventually we all going to have failed O-rings and pistons. This helps a lot.
@barryw.94194 ай бұрын
Awesome, maybe you could have set playback speed even faster, although the audio may have been 😂
@harderja3 ай бұрын
My piston was covered in grease I didn’t see any on your video. Should I clean it out???
@davidball30812 жыл бұрын
Disconnect circuit board and motor from trigger assembly housing and it goes back together in half the time. 👍
@ericsaresky62462 жыл бұрын
Wow! Did he do that wrong. No need to disassemble the cylinder, circuit board, or anything below the top. Remove the tools' housing half. Do not remove the center screw for the cylinder cover, cylinder cover pulls-out as one assembly. Pull the old piston/driver assembly out and separate from the elevator assembly. If the elevator assembly stays in the cylinder, that's okay. Carefully rotate the electric motor CCW as looking from the fan end, using the fan blades until the elevator assembly is all the way down (you will feel the motor becoming hard to turn, don't force past that point). Insert the new piston/driver and push it all the way down (it will be hard as the air below it escapes past the seal). Assembly the cylinder cover making sure the black tabs and the green tabs are even at 9:00 and 3:00 positions. Replace tool housing half and tighten screws. With no nails in the magazine, cycle the tool 2-3 times. Get back to work!
@iljanov2 жыл бұрын
Tried it with mine, the LED goes on with I presss the lower trigger, but nothing else works, please help
@chanoaguilar612 ай бұрын
Friend, where can I get the piston for the airstrike?
@naughtypine3 жыл бұрын
great job, thanks
@michaelhodge99025 жыл бұрын
Do a video about the driver blade replacement on a porter cable cordless nailer.
@carloslopez634911 ай бұрын
Oil don't have?
@carloslopez634911 ай бұрын
No sé lubrico el pistón ?
@domiszew51165 жыл бұрын
Witam, czy mógłby mnie pan oświecić, na jakiej zasadzie działa ten mechanizm? Skąd tłoki maja ciśnienie? Niby ten silniczek cofnie je do tyłu, ale w stanie spoczynku tłoki są z tyłu, wiec co je porusza?.
@wojciechsiwicki78115 жыл бұрын
Ja podejrzewam, że to nie ciśnienie "wbija" ten gwóźdź (tak jak w klasycznej gwoździarce), tylko podciśnienie. Jak naciskam spust, tłok jest cofany w cylindrze i wytwarza się próżnia (a przynajmniej znacznie niższe ciśnienie niż atmosferyczne). Jak tłok dojdzie do skrajnego położenia (czyli jak będą najdalej od czubka gwoździarki), zostaje zwolniony, i wytworzone podciśnienie zasysa go z powrotem do przodu i to wbija gwóźdź. Tak to sobie kiedyś wykoncypowałem. Mam nadzieję, że poprawnie.
@0YouCanCallMeAl04 жыл бұрын
@@wojciechsiwicki7811 czyli jednak ciśnienie, atmosferyczne ;)
@grzegorzwodecki31534 жыл бұрын
Czyżby gwoździarka z tą wada nie wbijała gwoździ do końca ?
@wojciechsiwicki78114 жыл бұрын
Tak, taki był objaw w moim egzemplarzu.
@MrKamel9904 жыл бұрын
gdzie kupiłeś tłok? i jaka cena?
@wojciechsiwicki78114 жыл бұрын
tutaj: www.elektro-global.pl cena to chyba 270 zł za dwupak (mi tak przysłali przynajmniej - a myślałem, że płacę za 1 sztukę). Później wyaukcjowałem jeszcze jedną taką gwoździarkę z takim samym uszkodzeniem, więc już drugi tłok miałem.
@claycharmsFOREVER5 жыл бұрын
Where can I get replacement parts for my AirStrike brad nailer?
@wojciechsiwicki78115 жыл бұрын
I've bought mine at polish distributor: www.elektro-global.pl/cat/r18n16g-l15s-18v-5133002308.html You can seach a local one.
@bizlarry5 жыл бұрын
Ereplacementparts.com if you haven't found it yet.
@garypollio49603 жыл бұрын
Ugh. Just buy a new one
@tonywhittle65202 жыл бұрын
DON'T BUY RYOBI!!!! I have had this piece of crap for about 3 years and done about 10 small project (about 100 nails). It has never worked. DO NOT BUY!!!!!!! CONSTANT JAMMING!!!!