SAMSUNG Scanner Locked Solve Problem

[@citizenrand0m]

It is considerably easier to start with the two screws on the back, shown at 1:44. This will allow the scanner unit to be lifted, giving much easier access to the first three screws underneath the unit, without the need to use any special tools. Also, in order to remove the document feeder hinges, they have to be pulled out vertically (it wasn't clear from the video due to the filming angle). I had to apply quite a bit of force, but be sure to apply it gradually, until they pop out.

[@MrRicoh]

You have given valuable advice and guidance to other people. I thank you for that. I hope this helps others. Thanks. ✔️ Access all lessons and bonuses ✔️ kzbin.info/aero/PLQGXf8WTvixODLzK3dJ6f_wiNp734mU_0 ✔️Be a supporting member ✔️ kzbin.info/door/OHtXTtGHj33pUm8Gf2FH3Ajoin

[@musondajoel1431]

@@MrRicoh i am now your follower for more advice on my printer.. thanks....and to the public out there just take your time and follow his steps it will do ...

[@rammohanrao3138]

Thank you so much... From India...

[@MrRicoh]

@rammohanrao3138 I'm glad I could help you. Did you manage to fix your printer?

[@musondajoel1431]

I appreciate you so much it worked for my printer ..its now scanning very well ..thank again.

[@MrRicoh]

I'm very glad I could help you.

[@bethsabath]

@@MrRicoh Are you mute or stuttering, or very ugly??

[@noamhamra2907]

Thank you very much for the help, you took a great photo.

[@MrRicoh]

Thank You I encourage viewers to support my channel: kzbin.info/door/OHtXTtGHj33pUm8Gf2FH3Ajoin Videos only for supporters: kzbin.info/aero/UUMOOHtXTtGHj33pUm8Gf2FH3A

[@domicyliat]

What is diffrence between red screwdriver (8:41) and black (8:12) - can I use only one of them?

[@MrRicoh]

Of course, you can only use one screwdriver. I checked which one was more convenient, but I didn't choose the best one.

[@ciceropaulosorantos]

Mestre vc tem um vídeo trocando a engrenagem do toner da Samsung,4080,?? Dês de já agradeço

[@jackkraken3888]

What did you use to lubricate the rod and gears? I heard lithium grease is not good for plastic and rubber.

[@MrRicoh]

This is a scanner lubricant manufactured by Kyocera

[@jackkraken3888]

@@MrRicoh Thanks! But I don't think I can get that for me. Is there any other alternative?

[@ubaldoluiz9691]

scx4200 scanner error at power on self-test. Does not recognize home position. Replaced flat cable, scanner module and cleaned the black stripe under the glass home position. what else can I do to solve the problem?

[@MrRicoh]

Do what I showed in the video.

[@AzamatAdilgali]

Thank you!!!

[@MrRicoh]

@AzamatAdilgali Thanks for your comment and I'm glad I helped you. Best regards

[@jerrymcg3199]

What type of grease did you apply?

[@MrRicoh]

KYOCERA SCANER GRASE

[@jerrymcg3199]

@@MrRicoh thanks

[@MrRicoh]

You can get more support in our Facebook group facebook.com/groups/270664767463482

[@frank.s74]

@@MrRicoh can't find it on amazon, can i use ordinary silicone grease?

[@orlandovera1181]

friend because my printer prints medina sheet well and the other half very clear can you help me with that? Greetings.

[@MrRicoh]

It is very easy. Just replace the toner and you'll be fine.

[@orlandovera1181]

@@MrRicoh I have already tried, I bought him a new tonner, changed the part that heats the fuser something like that, and I bought him new cartridges. and the same fault continues, it prints half a sheet well and the other half sheet is very light or blurred, and now I have another new fault, since yesterday it does not want to recognize the new cartridges, it tells me that it is incompatible.

[@normandcz]

Thank you for help!

[@MrRicoh]

Regards

[@b.anjaneyuluiamrich6295]

Hi sir my xrex samsung m2876nd scanner locked ani vasthundi plz help me

[@MrRicoh]

Wykonaj czynności serwisowe takie same jak pokazałem na filmie. Prawdopodobnie znajdziesz na zębatce silnika jakieś zabrudzenia.

[@jesusuzcategui-mw8lh]

Amigo en mi caso ya hice todo eso pero ni orende ni suena ya cambie cable y escáner que puedo hacer

[@MrRicoh]

¿Puedes mover suavemente el escáner con la mano de principio a fin?

[@jesusuzcategui-mw8lh]

@@MrRicoh si amigo y no hace nada ni si quiera prende

[@MrRicoh]

@jesusuzcategui-mw8lh ¿No has encontrado un pequeño trozo de plástico por ningún lado? porque tal vez algún sensor en las aletas no funciona.

[@MrRicoh]

@jesusuzcategui-mw8lh ¿No has encontrado un pequeño trozo de plástico por ningún lado? porque tal vez algún sensor en las aletas no funciona.

[@fabiosemino2214]

Just did this on a 2675f with a scanner that was screeching and it may have halted later, now it's like new

[@MrRicoh]

@fabiosemino2214 I didn't see that Samsung 2675f has the same design solution. Thank you for this message and best regards. I'm glad I could help you.

[@iskanderov19]

Спасибо, помогло. Белый ролик заедал. Смазал силиконом.

[@MrRicoh]

Я рад, что смог помочь тебе, мой друг. 🇺🇦

[@jabbathehut3541]

This didn't seem to solve the problem for my scanner. I even exchanged the CCD cable, but still something is bothering it. The scanning unit moves a little bit, then stops and the error message occurs (the scanning units' light is shining in red colour). If I detach the black rubber belt from the scanning unit, the same issues - any more ideas, what I could try? It would be so great to get it working again!

[@MrRicoh]

I would replace the scanner drive motor

[@mg8718]

Amen. I have the A1-2112 code. My scanner isnt locked. This printer is a piece of trash.

[@mg8718]

@@MrRicoh WRONG.

[@aryaninfotech85]

thanks

[@MrRicoh]

Cool. Thanks for your comment. Become my subscriber.

[@رابيدوللأحباروالطابعات]

Hello 👋 please help Printer samsung colour 480 c I need scan full page or copy not working

[@MrRicoh]

Something's probably blocking the scanner. Watch the movie and do what I showed in the movie. Subscribe to my channel.

[@رابيدوللأحباروالطابعات]

@@MrRicoh thank you for the information 🙏

[@truongnguyeninh8661]

I want to buy samsung m2675F the company is in stock

[@MrRicoh]

It's a good printer. Sometimes there is a problem with the scanner but as you can see there is a video that will help you quickly. Best wishes. KZbin SUPPORT: kzbin.info/door/OHtXTtGHj33pUm8Gf2FH3Ajoin PATREON: www.patreon.com/CopyExpertMovieStudio PATRONITE: www.patronite.pl/1796

[@jesusuzcategui-mw8lh]

Amigo tengo una 2675 pero me dice bloqueado pero no si quiera prende y ya le monte escáner nuevo cable todo y nada no hace absolutamente nada ni suena ni se mueve

[@babacreations2231]

Am getting vertical white space nearly 2 inch ..top to bottom of the paper..pls tell me the problem

[@MrRicoh]

Dirty optics, or dirty loading section, or damaged drum section.

[@pritamsingha6676]

super

[@MrRicoh]

Thank you for your comment and best regards. I wish you successful repairs of printers and copiers.

[@tamashornok6359]

👍👍👍

[@MrRicoh]

Thanks for your comment. For me it's very important. Subscribe to my channel if you can. Best regards. Parts for copiers www.copy-expert.pl/ Facebook: facebook.com/Copy-Expert-113431678801597/ Used parts www.copy-expert.com/

[@tpisuprimentos7076]

i have a problem with one c480fw, copys are perfect but when it is printing the colors arent matching, someone got the same problem?

[@MrRicoh]

I suggest you perform image calibration. This is an option available in your menu.

[@mg8718]

Throw that piece of shit in the trash and buy a new printer!

[@nanushaikh7040]

Sir i have problem in Samsung k2200 very dark🌑 print Memory print also I checked drum pcr But problem is continue

[@MrRicoh]

The drum cannot be checked. The drum unit needs to be replaced with a new one and it will be fine.

[@aniljanglepatil7094]

My printer scanner not removed plz help

[@MrRicoh]

Follow the procedure I showed in the video.

[@aniljanglepatil7094]

@@MrRicoh yes sir but not opening i trying

[@mikejok3r498]

Freaking good!!!

[@MrRicoh]

You're damn right :)

[@ayansajid9650]

i have samsung 4070fr its toner is printing out whole page black. i have changed pcr, drum and also refill it. in fact when i refill it and change drum after this it is printout black page. plss tell me solution

[@MrRicoh]

You made a mistake in regeneration. You installed the housings incorrectly or small gills from the ground. Not under voltage on the charge roller or drum. You may have buckled the gills and there's no contact.

[@ftousou]

what will you charge for this repair? 20-30-40 euro? a new one MFP starts from 90 your knowledge worth nothing for these market stay on copiers

[@MrRicoh]

Yes you are right this is not a good deal.

[@frank.s74]

@@MrRicoh If its a more expensive type like the ProXpress M3875FW in my case, its worth the repair, or bettter the self repair. That's why i find your videos very valuable. Please keep it up. And please continue without language that is how most understand it.

[@imtrue2132]

@@frank.s74 Same here with M2070FW , my scans has darkisch spots. And upon observation of the glass when cleaning I can see the other side of the glas is dirty with cloth streaks, perhaps from factory like that or static dust collecting.