Samsung Washing Machine Error Codes

Samsung Washing Machine Error Codes
What do Samsung washing machine error symbols mean? In this video, eSpares will run you through identifying error codes on a Samsung washing machine so you can get to the bottom of the problem. If you have one of the Samsung washer error codes, this is the video for you!
When your Samsung washing machine starts displaying error codes (such as error code E1, error code 4E, error code E2 and so on), trying to figure out what these washer errors are can be tricky. That's why Mat is here to explain the various Samsung washing machine fault codes to you, so you can identify the issue and get to work on fixing it without delay.
If you're in need of any washing machine spare parts or accessories for any repairs, head over to our online shop at the link below and we'll get you sorted. www.espares.co.uk/browse/at10...
To make sure you’re buying the correct parts for your particular appliance, you’ll first need to know its model number. Not sure how to find this? Watch our video on how to find your washing machine’s model number at the link below. • Energy Saving Tips For...
You can also watch our video on washing machine energy saving tips right here. • Energy Saving Tips For...
Want to skip straight to the information you need? Here's what we talk about in each part of our video:
0:00 Introducing the video
0:15 How error codes are displayed
0:41 The error code E1 or 4E
1:00 The error code E2 or 5E
1:30 The error code DE
1:46 The error code E7
1:57 Suggested video: How to Find The Model Number on a Washing Machine
2:02 The error code EB or BE
2:16 The error code HE1 or CE
2:28 The error code HE2, T5, T6, EC, TC
2:44 The error code E4 or UE
3:09 The error code 3E
3:20 The error code LE
3:38 Suggested video: Energy Saving Tips For Your Washing Machine
Thanks for watching!

[@shawnlucpicard]

Thank you so much all I had to do was open the drainage and clean it out. Thanks a million

[@manitarun2434]

THANKS BRO we were confused with our error code and by watching this video we solved our problem

[@eSpares]

+mani tarun You are welcome. :-)

[@eSpares]

Reply to Fred Morgan: Error 4E or 4C relate to a water supply or filling error. Check how quick it is filling and how much water is in the drum when the error is showing. If the water level is not reaching the correct level within a couple of minutes (slow filling) it times out and shows error. If the water is at a high level check the hose to the pressure switch as these can rub on the drum and make a hole. The pressure then escapes and the machine thinks it has not filled.

[@anilkumar1971]

Hi I'm getting error code 4C2? What is that? Is it anything serious with the washer? Its brand new washer (USA)..Please help..

[@eSpares]

You have not given a make and model number, however on Samsung washers 'This occurs when the temperature exceeds 50, for over 8 seconds in the Wool and Delicate's course'. You may have to reduce your water temperature fed to the hot supply on your machine.

[@anilkumar1971]

MODEL NUMBER WA50K8600AV/A2 TOP LOAD WASHER..PLEASE HELP...

[@eSpares]

Check that water temperature, you could try pouring some cold into the machine first as this may help if your supply is to hot for the machine.

[@jenniferlove5566]

eSpares and uui

[@ayhancapan]

Thank you... So it was the filter. And i've fixed it as how you showed... Thank you...

[@eSpares]

You are welcome Ayhan.

[@non14200]

Hey thank you for this great video , could you please tell me what is the solution with 8E error in my Samsung washing machine

[@eSpares]

Hi Abdullah, this is explained at 2:02 (BE) and the problem is likely to be the control board.

[@kylewenning5014]

thank u. helped me fix it in less then 5 minutes.

[@eSpares]

Hi Kyle, thank you for your post and glad we could help.

[@Yaz2id]

THANK YOUUUUUU MATH

[@eSpares]

😊

[@dsmatheny3790]

Thank you so much for the information. I really do appreciate your time.

[@eSpares]

Hi DS MATHENY, thank you for your post and glad we could help.

[@georgiafan6618]

My washer displayed the “fN” code before dumping its entire contents into the washer pan below unit. Prior, we cleaned debris trap, removed, inspected and cleaned pump and it’s associated lines, cleaned door boot gasket/reinstalled spring assisted boot wire retainer. All appeared viable. Both Inlet Hoses replaced with braided SS. Unit ran well for 2 weeks until it dumped its water contents last night (pan prevented dire situation). Observed steady leak from bottom front panel, left side. We did clean detergent/softener drawer prior. I’m thinking boot gasket. What do you think? Thanks for video.

[@marciamunoz7074]

Thank you thank you thank you thank you!!!!! You are my HERO!! I watched your video (several times lol) and got the courage to try and fix my less than a year old Samsung front loader washer. I couldn’t remember the error code my washer displayed so I did another cycle and saw 5E then went back to your video and saw what to try...omg I couldn’t believe what was in there!! Mind you I have 3 young kids. I found a baby sock water bottle caps nestle crunch wrapper and rubber bracelets. Oh and like 3 gallons of water! Hahaha! Then I turned back on (thank you for that safety step I would of completely overlooked otherwise) and I prayed it would work because I had all these wet towels now and PRESTO IT WORKED!!! Spinning like a Maytag hehe. And my boyfriend told me to call Samsung customer service for a technician visit Ha! No thanks I found and watched espares instead 🤗

[@eSpares]

Hi Marcia, well done that's made my day that we were able to help you fix it yourself, remember to like the video and subscribe for even more useful videos.

[@gears5665]

SE is not spin error then. 5 E . Output error: check the filter. Your video was more useful than Samsung's website! Thank you.

[@eSpares]

+gears5665 Thanks for the comment, hope the video has helped.

[@felixedgardosantia2769]

thanks for your video. It served me a lot.

[@eSpares]

Hi Ministro Felix Edgardo Santiago , glad you found our video helpful. Remember to like and subscribe for more helpful videos in the future.

[@happyboysngals9627]

thanks buddy, you just fixed my machine (code 5E). subscribed.

[@eSpares]

Hi happy boysngals, glad we could help and thanks for subscribing.

[@Ellerocks01]

Thankyou so much for this video, I have had the 5E error code for months, thought I would have to get thee repair guy to come take the thing apart and clean the filter, i haven't been using it because of that. I didn't realize how easy I could do that myself, man it was full of dog hair I think.

[@eSpares]

Thanks for the comments Michelle, remember to 'like’ the video if you enjoyed it or it helped.👍

[@kiran1112]

Hi Matt,how to access the motor in this samsung washing machine (b1245a) for checking carbon brushes.There isn't a removable back panel,do we need to use the shipping bolts to secure the drum before placing the machine on its side?

[@eSpares]

Hi Kiram, do not use the shipping bolts just gently lower onto a soft surface. You can lower the machine down as shown in this video here: kzbin.info/www/bejne/rWqplWuEjL2UZqMm14s

[@nazikalgenied7764]

Hi,my washing machine model no.WD0704REW make an errorF3E on its scr een and stops working after start.what is the solution

[@djreaction1]

NF1 is a popular one from my machine, but I didn't hear you mention that code, any help would be great! Thank you!

[@eSpares]

Hi Richard, We believe this is a fill problem (possibly due to the hot water hose connected to the cold input). Check the water fills correctly by selecting a cold wash or rinse and it fills to the correct level in the allowed time (usually less than a minute).

[@djreaction1]

eSpares any ideas of why it only shows me the error code when it's on the bedding setting though? I did a quick wash setting and all went fine.

[@eSpares]

Your machine will fill with different combinations of water depending on the cycle. Check your water supply is filling correctly and see another video for more information: kzbin.info/www/bejne/jISXaXqVmNx2jtE

[@moaathalmaani3058]

God bless you that was soooo useful

[@eSpares]

Thanks Moaath, glad to know you enjoyed this video. Remember to like and subscribe for more helpful videos in the future.

[@debbiewilliamson2523]

Hi Matt. Could you please tell me what a flashing red drum symbol means on my Samsung Ecobubble? Many thanks Debbie

[@eSpares]

If the machine 'appears' to be working normally we believe the symbol is reminding you to do a tub clean. Check your instruction book for details on this.

[@MdIqbal-tc4jb]

Thank you sir

[@eSpares]

Hi Mohammed, thank you for the post and you are very welcome and have a lovely day.

[@Neophoria]

Thank you

[@eSpares]

+mohammed j :-)

[@Estelle001100]

Hi! I need assistance please. Samsung error dE1? What is the problem? We did 2 test runs without any problem.

[@jessicali9773]

Very good tutorial thanks

[@eSpares]

Hi jessica, glad you enjoyed the video.

[@FredMorgan-1]

Great video and very comprehensive, I just bought a WW70J3 machine and it keeps stopping with error code 4C. Checked all the pipes and water supply which all look fine. Cold water feed only. Any suggestions would be great....Thanks

[@FredMorgan-1]

+Fred Morgan Just came across some more info so looks like 4E = 4C

[@eSpares]

+Fred Morgan Check how quickly the machine is filling. If this seems normal check the pressure switch hose is not blocked as the machine will not see the water level and shut down.

[@FredMorgan-1]

+eSpares Thanks for the comeback but now realise that the actual water pressure must have been too low. Previous machines have worked ok so thought that would this one be ok. Fitted to water main supply and now working ok

[@eSpares]

+Fred Morgan :-0

[@mystylemystyle198]

Thank you so much

[@mystylemystyle198]

My machine showing b62

[@carlabozzano]

Thanks for your videos. Please, could you tell me how to sort out the error Uc on Samsung WF0700NCW? Thanks again.

[@eSpares]

Hi Carla, error UC is a voltage supply error and may be caused by a 'bad' connection to the electrical supply. Check it is not UE error as this is a balanced load problem.

[@carlabozzano]

eSpares Thank you for your answer. I have already checked the balance of the load in it. I clean all the filters, emptied all the canes, changed the connection of the power supply and still persist the problem. Also, I re-calibrated the machine. In any case, I am thankful for your answer. Keep it up ☺

[@eSpares]

Your problem could be a loose connection anywhere from the machines power switch to the fuse board. If it is a poor connection it is likely to occur when there is an increase in power used ie when the machine heats or spins. This may even show if you plug a light into the socket next to the machine as it may cause a standard bulb to flicker if the power is the problem.

[@carlabozzano]

eSpares Ahaaa! You are right, because, most of the time, the machine stops after heating the water or spins.. What should I do? Shall I call a technician? 🤔

[@eSpares]

You may need a house wiring technician not an appliance engineer. Can you try the machine on a different power point?.

[@guseinli3478]

thanks 🙂

[@eSpares]

Your Welcome:)

[@karinamanning9592]

Mine was showing 06 or U6, don't remember. I turned it off, open the door but close was still very wet. What does it mean?

[@cannicusgladiatus268]

Hi, My Washer Samsung WD856UHSA says error Code AE. what does it means? how can i fix it?

[@eSpares]

This means the control board cannot talk to the main module. This could be a loose or damaged connector so check them all for any signs of damage or corrosion.

[@butterflyzavala78]

hi thank you for sharing this information but my washer show it like mesajes not like codes in my case sometimes show sd or sud msj please if you can help me I will appreciate your comment.

[@eSpares]

Hi Blanca, your machine is showing sud to indicate there is too much foam from excess detergent. Run a rinse cycle and use less detergent on your washes and the problem should be resolved.

[@butterflyzavala78]

Thank you so much 👌

[@eSpares]

😊

[@eSpares]

Your Welcome.

[@MariaHernandez-go8te]

I have a Samsung top loader washing machine. I am not getting any error codes but it is not washing. The door is locked and can't I get it unlock or start washing. Have you ran in to anything like this?

[@eSpares]

+Maria Hernandez Many machines have a thermal door lock that prevents the door unlocking when water is in. Try unplugging the machine and waiting for three minutes. if this does not work see another video: kzbin.info/www/bejne/qV7CqWWqiNKXZqM

[@reissmason1990]

hi great vid i have a samsung ecobubble with SUD code how do i fix this please?

[@eSpares]

This is caused by to much foam from excess detergent. Use a washing machine cleaner like: www.espares.co.uk/product/es1566874 and then reduce the detergent used.

[@neil_digital]

Could you let me know where the SUD sensor is in the Samsung ecobubble

[@praveenbalodi4493]

My Samsung wf8558nmw8 front load washing machine is showing error code Uc and Un. Can u pls tell me whats the real problem.

[@eSpares]

Hi Praveen, this sounds like you have an unbalanced load especially if the errors occurred at the end of a cycle and the machine has either shook on spin or not finished spinning. For more information on balancing your washing see our video: kzbin.info/www/bejne/q3ylqmBvg6p5a6M

[@doemugyvandoe7288]

eSpares Uc code what is it

[@himatullahkarokhil4505]

Hello, can you you please tell, What does "b2" error code means? on samsung washing machine 7kg diamond.

[@eSpares]

Hi Himat, B2/BE2 refers to a control button issue so check the buttons as they may be sticking.

[@katerinaivanovska9115]

hi I have Samsung diamond 6.2kg and I also have SUD error. what does that mean? thank you

[@eSpares]

The error SUD is to indicate an excessive amount of foam or suds in the drum. This can be caused by too much detergent or a build up in the machine. . If this happens run a rinse and spin cycle and reduce the detergent quantity on future loads.

[@mitzimatsumoto3993]

Is it possible to put a video on Panasonic washing machine??

[@eSpares]

Hi Mitzi, we will try and produce a fault code video for Panasonic machines in the near future.

[@henryxavier3751]

Thank you E3 👍

[@eSpares]

Hi Henry, E3 means the machine has detected an overflow issue which is usually caused by too much detergent in the system.

[@henryxavier3751]

Thank you

[@adamornelas1882]

Hello! Do you have any advice or help for error code, "nF"? This is on a Samsung front load washer, model number WF316LAS/XAA.

[@eSpares]

Hi Adam, error code nF means the machine has detected a problem with the machine filling up, check you are getting water to the machine and test the inlet valve.

[@dsmatheny3790]

Do you have a video on how to open the washer and replace the temperature sensor?

[@eSpares]

Hi DS MATHENY, we don't currently have a video and we don't have your model details but most machines will have screws holding the top on at the back and an access panel on the back cabinet so start there.

[@dsmatheny3790]

@@eSpares Thank you sir. I hope you have a good day.

[@eSpares]

@@dsmatheny3790 you too and please let us know how you get on.

[@hmdosti7520]

Hi I have a Samsung washing top load it fills with water then shows 4E and drains right away

[@eSpares]

Hi, this is where the machine 'thinks' there is a filling problem. If it is filling to the usual level (or above) just before the error check the pressure switch hose as on some Samsung washers it can wear a hole if it rubs on the drum during spin. For more information see another video: kzbin.info/www/bejne/aKGsh553rbyGjsk

[@lxx6700]

Fe code please tell me what i have to fixed thanks

[@bijeeshkk4816]

I have wf b1061 2 E error wt the problem and how wil..

[@jessicaludivina3035]

Hi... my Samsung front load washing mashing (WD146UVHJRA) doesn't give me any error code but it displays Hot and the lock symbol and it won't open the door... after a normal cycle of "quick wash" ... I didn't even used the drying ... could you please tell why is it doing it? And how can I stop it? Please!!! Thanks!

[@jennifiercools9866]

This is an excellent video! My error code says E3, I just would like for you to spell the type of coil you referred to in the video. I googled how I thought it was spelled and got some vehicle car part. Thanks.

[@jennifiercools9866]

So I found in the comments you spelled it "tacko" coil. I followed the link you provided, but mine doesn't seem to have those problems described. I just put my Samsung front load washer model number WF56H9100AG/A2 in diagnostic mode (by pushing "spin, soil level, power" at the same time). Went to "TST" mode and immediately blinks "3E2". Any ideas? Thanks in advance.

[@eSpares]

Hi Jennifier, the tacho coil fits in the motor usually at the top but you need to check it as it may just be loose, here is a link to show you the part www.espares.co.uk/search/ca1236/washers-and-dryers?SearchTerm=tacho

[@jennifiercools9866]

eSpares thank you!

[@eSpares]

Hi Jennifier, no problem we are always here to help.

[@Fernando-ew6eo]

Hello my washing machine samsung eco bubble presents the following error code ss 3 1400 and orange padlock flashing greetings and thanks

[@eSpares]

Hi Fernando, we can't find any ss3 error listed, however it sounds like the child lock may have accidentally been activated. Look at the controls for an image of a child's face or a padlock with marks to two buttons. By holding the two buttons at the same time for 5 seconds it should release the lock if this is the case.

[@FaaTi]

wd90j6400ax Shows LC1 just as it draws water bought only a week ago?

[@eSpares]

LC1 error is indicating the machine has low water level (it has not filled to the correct level in the allowed time). Check the water supply is turned fully on to the pipes and the hose is not trapped. Also check the drain hose is not lower than the water level in the drum or the water may be running out as the machine fills. For more information see our video: kzbin.info/www/bejne/jISXaXqVmNx2jtE

[@georgecarlson3033]

Hi - I have a Samsung 8.0kg SW80SP top loading wishing machine with error dE - please help ! Ive read that this is a door problem but there are no locking mechanisms for top loaders

[@eSpares]

The door may not have a lock but there is usually a switch that recognises it is closed. There may be a magnet on the lid on some models that can come off causing this problem.

[@sonjaemery]

The error code I get is 8e. Any ideas would be great. Thx

[@eSpares]

This sounds like BE not 8E and that is likely to be a PCB problem see 2:02

[@crisrx77]

Sonja Emery did you get your washing machine fixed

[@merrilljohnson937]

eSpares

[@mrsflash100]

I have a Samsung front loader WF1752WPC, This morning set it to a cotton load pushed start button and display panel board lights just started spinning around in three circles. I thought it may be a waiting to start thin but cycle didn't start. Any ideas? No codes came up just the spinning digital display on the timer panel.

[@eSpares]

Hi Marion, many machines now 'weigh' the load by checking what power is needed to turn the drum. If the load was either heavier or lighter than the expected load for the cycle or giving unclear results (possibly a large single item tumbling unevenly) the machine may keep retrying to identify the weight. Try on a different load or a different cycle before assuming a fault on the machine.

[@aviewfromsouthafrica2680]

Hi there, please assist me, I have an "OE" error on my samsung. I noticed also that the water level was very high at some point inside the machine

[@eSpares]

Hi A view From South Africa, OE refers to the washi9ng machine has been unable to drain the water during the wash cycle, check the drain hose, filter and drain pump.

[@HS-re7dw]

Hi! i 've seen ur video of HE1 which concern heater ,but i have this prob by even using cold water .why so

[@HS-re7dw]

I forgot to mention when the machine is stopped and started again it usually does not stio.Thank you

[@eSpares]

+Hamish Sampai It is likely the heater is failing or it has resistance to ground. This could cause it to be intermittent.

[@HS-re7dw]

Thank you very much for ur response!

[@eSpares]

+Hamish Sampai :-)

[@mustaphamarrakech12]

thinks for information

[@eSpares]

:-)

[@imanmk531]

Hi I need your help in error code lc1 for Samsung washing machine

[@eSpares]

Hi Iman MK, error code LC1 means the machine has detected low water levels inside the machine, check the drain hose is not too low which can cause syphoning and make sure you haven't got a leak which will cause it as well.

[@ranbuch]

Saved my life

[@eSpares]

+Ran Buchnik Glad to help.:-)

[@hhhhhjjj234]

thank you for your video you forget to add in case of 5E code it could be the sewage pump. after checking for clogged filter then the blockage in hose . to dismantle this pump we schould remove the front panel all you need is screwdriver, remove the door seal also , the pump is the right bottom , chech the inside hose too

[@eSpares]

Hi Gadouche Brahim, thanks for the post and helpful comments. We have mentioned 5E error code at 1:05. Thanks for tuning in.

[@hhhhhjjj234]

@@eSpares yes i know thanks to your video i have just repaired mine a samsung wd j1255 5E error code i changed a new drain pump and it was ok the electric resistance was good i powered the pump it works guess what ? the pump was weak under load when i filled the drum it stops from time to time and if you rise hight the drain hose the pump won t work so if you find the resistance good it doesn t mean the pump is good

[@eSpares]

Hi Gadouche Brahim, thanks for your comments. Glad you were able to fix your appliance. Well done :)

[@user-yn4me9lh6t]

What model is it?

[@danielwashington9665]

hi I have a Samsung ww90j5456mw and when you put it on a programme nothing happens and it displays DC thanks

[@mdavis086]

I have a Samsung wf330anw/xaa with a LO error code and keeps locking as soon as you close the door and keeps triggering the lock like 7 times and comes up with LO code..any info would be great..

[@eSpares]

Check nothing is stopping the latch locking the door and replace the lock if required.

[@keithmitton4558]

I have a Te2 error appear on my machine display. You haven't identified how to fix this issue in this video. Can you please provide me with some insight and some instruction.

[@eSpares]

+Keith Mitton We believe TE2 is a temperature sensor error so check the NTC sensor on the heating element and the wires/connector. If you cannot see a problem it is possible the sensor is faulty and would require replacing..

[@keithmitton4558]

thanks for that... where would I find thw sensor. Is there a diagram I could look at

[@eSpares]

+Keith Mitton We do not have a circuit or diagram you can access but we have a video showing the sensor when replacing the heater at: kzbin.info/www/bejne/pWHdfYeqeMeeodk

[@lauragliebe8632]

What about nF1?

[@eSpares]

Hi, Laura, we believe that this error code refers to the hot/cold connection is not correct, so check to make sure the hoses are on the right way. Let us know how you get on.

[@mffdesigner]

I got a WF328AAW/XAA which was showing error ND. I called a technician. He suggested to change the control board. How I changed that and it's showing error E3. What do you suggest? Also I didn't see this error code on this video. Tks.

[@eSpares]

Hi Marcos, "E3"could mean the door is not closed properly. Either there something preventing it from closing properly (blockage) or there is a fault with the locking mechanism.

[@eSpares]

If that does work try a machine reset as follows: 1. With the power on press and hold down the start button. 2. While still holding the button down turn the dial one click anti-clockwise (15-minute cycle on mine) 3. If it shows '8888' on the display then skip to step 5 if it shows 'E3' turn the dial back to the off position. 4. Press and hold the start button down and again turn the dial one click anti-clockwise (15-minute cycle on mine) 5. With '8888' now displaying hold the start button in for 1 minute. 6. Stop pressing the start button. 7. Return the dial to the off position.

[@backdarxkmgamingxx8119]

Thanks

[@eSpares]

+albahr m :-)

[@ruizd3623]

+eSpares I have a Samsung silvercare front load washer was getting error code nd wich I found out it was to do with pump so check for debris nothing so next I replaced the pump and know I'm getting a error code f3 what is f3

[@eSpares]

Error ND was no drain and could be a blockage or failed pump. E3 error is saying the control board is not identifying drum motor movement when it should be turning. Check you have not disturbed the motor connection when fitting the pump.

[@swilson6206]

IS THERE A DIAGNOSTIC MODE FOR SAMSUNG WASHERS? HOW DO YOU GET TO THE DIAGNOSTIC MODE? OUR WASHER IS WF218ANWXAA

[@eSpares]

+s wilson Sorry we do not have the information for the diagnosis mode. We suggest you have a look at our diagnosis videos as this should help identify the problem see: kzbin.info/aero/PLZopaZU-UQSHj1noiwEJ99JjXWcEcSAbZ

[@rafiaabeke3899]

my Samsung washing machine WF1124 showing 8E pls show how to replace the sensor.

[@eSpares]

At 2:02 we say 'Now if your machine is displaying EB all BE this is a motor triac error. And this is normally to do with a fault in the control board. We do not have any other information on replacing this part.

[@blakeriley3590]

Just had a repair person out to fix the latest recall - when he left he started a self clean cycle then it stopped and there is an error code flashing SC - what's wrong ?

[@eSpares]

The SC is likely to be the fact it is in a Self Clean cycle as this is not a recognised error code. If EMPTY you can check the pump filter is clear (use a towel or tray for the little water in the pump). Then if the cycle has finished switch off and restart with a 'test cycle' on a short wash to see if it has a problem.

[@thehardtailhero69]

Relating to an LE code, how might I find the leak and where is it probable to be?

[@eSpares]

Hi The Hardtail Hero, make sure you check the level of the drain hose first as if it's too low it can cause the error code, if it's a leak there will be signs of water on the floor underneath or at the back and water trails may indicate where it's coming from.

[@georgiahirakis270]

what about error door open, we order a new latch for the door it was replaced and it still says door is open any suggestions?

[@eSpares]

Hi Georgia, if the machine is showing a door error then check the door lock.

[@kitkatwelshlady8465]

I am getting a flashing 3E or 33?? drum is shaking not washing clothes at all after 25-30mins?? 🤔

[@eSpares]

Error 3E is a motor 'tacho' error. this is a coil or sensor on the motor that identifies the drum speed as it turns. Check the motor connections and see our video: kzbin.info/www/bejne/emakqGp5d6p6hqs

[@lindashaw606]

u6 error code what does it mean?

[@kristimontgomery6233]

My samsung front load washer is displaying the error code EE, but the top portion of the first E is missing. What does this mean?

[@eSpares]

Hi Kristi, the only information I can find on this error indicates it may be a eeprom error (the control board programme memory) so it may indicate you need a new control board.

[@Fa6aMiTheAdubber]

I thought I saw 'SC' on my washing machine (WF602U0BHSD) but I can't seem to find anything about it and so I assume its 5E since I know the door won't open since it's full of water

[@eSpares]

The error 5E is a drain error and is likely caused by debris in the drain pump. Lower the drain hose to a shallow bowl to let the water run out and when empty pop a towel under the filter at the front. You then can take out the filter and remove any foreign objects.

[@Dk-de2ff]

Sir I lost my fan belt of Samsung front loaded washing machine and I can't find the model number and how I identify the model number please sir reply fast

[@easyclearpool]

Mine currently will not unlock the door and unplugging it overnight and back in it is stuck on 13 minutes still and door continues to be locked once powered on. After 3 to 5 minutes of it nothing it says AE6 each time. Thinking about replacing control board, and see I'd I get lucky, any thoughts?

[@eSpares]

Hi Berry, not an easy one to sort as the machine has detected an communication error between the main board and the inverter board, you will need to check the contacts and any signs of damage to either board.

[@aiizenshore607]

how i can fix 3E ??

[@eSpares]

+Aiizen ShoRe Check the wires on the motor as described at 3:09. The fault may be the motor or board.

[@eliasgo1]

Hi Fernando My Samsung Top Load Washer Model WA40J3000AW/A2 and am having a issue It makes a gear grinder sound during the wash cycle grinds and stops and grinds and stops and so on.. I've tried it with and without clothes and still the same The Ligth(Normal/No bedding Cycle) flashes on and them of and so on...it sounds like he tried to spind but stops also stays full with water inside, I check for any dirty stuff but is clean Need help Thank You!

[@eSpares]

Open the door and try rotating the drum. If it is catching or grinding it may have something stuck between the drum and tub. We are not too familiar with this machine in the UK but believe there is a bolt in the centre of the drum that once removed may allow the drum to be taken out and anything caught under accessed.

[@eliasgo1]

OK First of all Thank You for helping me, I did what you ask me to do I open the door and I spin the drum with my hands and sounds ok no noise but I forget to tell you that the company did the Re-call on this Washer machine few moths ago after that they send me some service repair company (Because the warranty) And this is what they did. On the First visit they replace the Main PCV, Called CX back after a Cycle. According to them shows this : Defect Code ARCS , Also Repair Code CR01 Factory Modification.(Repairs were made no change) The second visit they Replace Main PCB,Condenser, and Dampers According to them shows this Defect Code APPR and also Repair Code ALEL Aligment, Electrical. (Repair were made no change still the same) On the Third visit they replaced Clutch and Motor according to them shows this Defect Code DISP and also Repair Code ALME . Repairs were made no change still the same until now all this information i got it from theirs Service Orders they provide me.

[@eSpares]

I thought this was a 'new problem' not something that has been ongoing. As we previously stated we are not familiar with this model but it appears to be direct drive drum. On wash if the noise is still present it is likely to be a main motor problem or drum bearings/suspension. If the problem occurs when emptying i is more likely to be a pump related problem. Sorry we do not have more information to narrow it down more than this.

[@eliasgo1]

Understood ... I checked the pump is clean and working this issue happens in between 2 o 3 Min after we put the washer machine to work on normal Cycle flashes and not move the noise i heard is like the motor try to work for one second and cant make it and so on . But thank u for your help!

[@erastongamilaga8015]

Hi my washing mashine is samsung 16kg it has probrem water overflow over the soap drawer I dont know what could be the probrem .please support

[@eSpares]

This usually happens if too much powder has blocked in the hose to the drum. Check and clean if required.

[@waveyynishlmg399]

What does dC mean?

[@jessemartinez5447]

What does TE stand for???

[@eSpares]

+Jesse Martinez We do not have TE listed for Samsung error codes but it is likely to stand for a Temperature error. Check the heater and the temperature sensor as shown at 2:28

[@signalsoldier]

What is a 5r or Sr code.... I cant find this code anywhere

[@eSpares]

This problem may be a control panel problem but we cannot confirm this. May be worth watching this video: kzbin.info/www/bejne/h4qzoqOggbtqqZY

[@harmanpreetkaur4184]

what about draining error code

[@mstinamichele]

Our error code is nf. I understand this is a filling error as well?

[@eSpares]

+Tina S. If the machine is filling but you get NF then check the hose to the pressure switch. If it is not filling check the valves and water supply. See our video: kzbin.info?o=U#

[@israelsanchez2891]

Hi great video, the display of my samsung machine marks E3 what is the problem there?

[@eSpares]

Your error is indicating the control board cannot identify the motor turning. If the drum does not move check the motor brushes. If it spins fast and stops check the wires on the coil on the end of the motor.

[@ask6378]

Hello there, i search for " Samsung WF81F5E5P4W Washing Machine control board " any help ?

[@shrekas2966]

i have a problem on samsung ww60j3083lw/le i think its a code 4h. it wont take water. maybe its something with water presure but i use open water source that has alot of presure becauss when i take off hose it just bursts water so the presure is fine. it has something to to with water taking into machine itself because it operates without water so i turn it off.

[@eSpares]

+Shrekas 2 Thanks for your comment, we recommend you have a look at our diagnosis video: kzbin.info/www/bejne/jISXaXqVmNx2jtE

[@sasacvetkovic127]

I am having no error code. Machine is working normaly than from 9 minutes goes to 10 than to 9 and like that until eternaty. It may happen on 31 min, etc... Any solution?

[@eSpares]

Hi Sasa, If the machine is washing normally it may be when it gets to the heating that it then starts to recalculate the time due to it, not heating, you will need to test the heater first and we have an advice article and video to help www.espares.co.uk/advice/symptom/washing-machine-is-not-finishing just copy and paste into your browser and let us know how you get on.

[@coastwideflooring9369]

Hi i have a samsung top load washing machine. I have just replaced the drain pump but it now drains the water straight out as it enters the bowl . Please tell me what is happening ?

[@eSpares]

Hi Coastwide Flooring, check the drain hose is not too low to the ground as it may be causing the washing machine syphon the water straight out.

[@goodlife3341]

PEI can you tell me what this code represents

[@srishtisingh8620]

hi, my machine is not showing any error..it is showing 69..but red is indicating just below lock indicator..wat can be the issue?

[@eSpares]

Hi Srishti, we do not recognise this problem symptom. The best way to identify what is going wrong is to watch some of our diagnosis videos to establish what parts of your machine are working. For more information watch this video: kzbin.info/www/bejne/h4qzoqOggbtqqZY

[@takotako8090]

Hello , my samsung error code is Sud what it means ? Please help me , what can I do?

[@eSpares]

This is too much detergent (suds) so reduce the amount used and run a rinse cycle on the machine before using it again.

[@dmercydmx3286]

Error OF/oFModel WD146UVHJSM. Thanks!!!

[@eSpares]

Hi DMercy this is off samsung CODE: OE, OF, E3, OC (Overflow) Action: Too much washing powder/liquid may have been added. Switch off the power to the appliance, wait 30 seconds then switch the power supply back on. The drain pump should operate to drain the washing machine.

[@roamrioedwards4528]

hey my machine is showing like a reverse 6 or upside down p can you explain that one?

[@eSpares]

+Roamrio Edwards If the machine isnot starting check the door lock as the machine may be indicating d for door lock.

[@roamrioedwards4528]

+eSpares No its not the door because when the machine is filling up the water it just stop I think it's the motor problem you talked about in the video

[@eSpares]

+Roamrio Edwards To help identify your problem have a look at our diagnosis videos: kzbin.info/aero/PLZopaZU-UQSHj1noiwEJ99JjXWcEcSAbZ

[@roamrioedwards4528]

+eSpares. Okay thanks

[@raymondelledge9252]

Mine shows an nd code even after I cleaned filter drain runs a cycle an stops with water still in it and won't wash

[@aracelymoreno5859]

Can you please help me, my Samsung DRYER is displaying DC?

[@bestmarketingsolutionsobi4330]

hi, what does sd error code mean

[@eSpares]

Hi Masood, a SD error is indicating to much suds from the detergent. If you are using detergent for automatic washing machines reduce the amount used and the problem will go away. You can also ensure the machine is cleaned from detergent build up by using the product featured in this video: kzbin.info/www/bejne/n5e6fGyam5aknck

[@dianes8048]

My front loader has a 4C2 error code and an alarm. Any ideas as to how to resolve this? Thanks.

[@eSpares]

Hi diane, 4C2 means the machine has detected an issue with the water temperature, check the water hose is connected to a cold supply and test the heater.

[@dianes8048]

@@eSpares Thanks so much for your response. I have had this washer for almost 2 years and it has never done this. Thanks, again!

[@paulsingh2912]

I have a Samsung washing machine type WF1124XAC 12 kg I turn on electricity Switch on the power switch It gives display Accepts the washing programme After placing clothes and open the water tap when I press start does not work Stay for two minutes and then appears on the screen - Voltage Control - U/C call for service What should I do and what is the solution?

[@eSpares]

The error suggests there may be a problem with the electric supply to the machine. Disconnect the supply and check the power connection and wires are all tight and not arcing or burning.

[@kamalayash8791]

Hello. I have samsung WF1602W5v and its showinng (SUD)..how could we solve it? thanks in advance..

[@eSpares]

+Kamal Ayash The reason for a SUD error is the machine has detected to much lather. This is likely to be due to excess detergent or the wrong detergent type (must be for 'Automatic or HE high efficiency machines). If using the right detergent run your machine empty with a washing machine cleaner product to remove detergent build up and reduce the amount of detergent you are putting in.

[@user-qf9me1oe8f]

My washing machine model WD0754W8EH Show me code error FE, what's problem and how can i fix it ? Help me please,,, Thanks...

[@eSpares]

If this is a washer dryer check the drying fan motor turns freely and runs correctly.

[@lupojacobo9892]

Whats 3C2 ??

[@eSpares]

Hi Lupo, the machine has detected an issue with the motor circuit, it has a few possibilities so check the motor, hall sensor or the tacho.

[@dsmatheny3790]

What does tE mean and what does Cb mean sir?

[@eSpares]

Hi DS MATHENY, tE means the machine has detected a temperature sensor error so test the sensor with a multimeter, Cb is for calibrating the weight sensors in the machine which has probably been activated by mistake.

[@wahyuroberts2330]

Hi.. I just bought washer Samsung WA45K7600A/WA45K7100A.when I tried to used for the first time during after the spin the machine was drain but the water filled again and has code Ur..what should I do?

[@eSpares]

We do not recognise an error UR but UB refers to a balanced load problem. For more information on that see our video: kzbin.info/www/bejne/q3ylqmBvg6p5a6M

[@annrodriguez2460]

please help. my washing machine is giving me an OE code. i did what u said and its still doing it.

[@eSpares]

DE is a door error have you replaced the door lock?.