Samsung Washing Machine Diagnostic Mode Guide! How To Check Error Code & Test?

[@djblox8896]

do you know what eot and pst means? thanks

[@How-to-repair]

HELP NEEDED!! not at the moment but i will pin this to the top of page so some helpful samung engineer might give us the answer

[@mattbandura9015]

DARK GARMENT : Washing Motor Work Test (“PSt”) *check water level

[@mattbandura9015]

OUTDOOR CARE : EEPROM Test (Eok : OK, Eng : NG)

[@mattbandura9015]

B. The Sensor & Motor can be tested when you rotate the course encoder.​ - COTTON : Micom Software Code check​ - SUPER ECO WASH : Model Option Check ​ - BEDDING : Water Level Frequency (ex. 242 -> 24.20kHz)​ - DAILY WASH : Water Temperature (ex. 254 -> 25.4℃) - DELICATES : Air Temperature (ex. 300 -> 30.0 ℃) *not used​ - BABY CARE : Duct Temperature (ex. 300 -> 30.0 ℃) *not used​ - OUTDOOR CARE : EEPROM Test (Eok : OK, Eng : NG)​ - DARK GARMENT : Washing Motor Work Test (“PSt”) *check water level​ - ECO DRUM CLEAN : Washing Motor Work Test (“tst”)​ - RINSE+SPIN : Spin Motor Work Test (“SPN” , move to MAX RPM)

[@How-to-repair]

thank you so much for assisting i learned something today thank you

[@Corporal_Hicks]

This Works for Me! Try This for AUTO Service Mode 1: Set it to Cotton Program 2: Press Delay Button until 17h Now Press and Hold Start Button until AS comes up on Screen. Press Start Button for full Test or Delay Button for individual Test Programs.

[@rogetparyente3343]

What an amazing clean and clear detailed testing video! Yep I fixed my machine thanks to this video, the motor did not spin, - for your info, water goes in, and when its time to spin it simply stops and no error so going into test mode, the error shows I think C3 - changed the brushes on the motor, one was practically finished the other one had half. So i got a pair of brushes for about £5 and that fixed the machine.

[@mustafizrahman4469]

I am a pharmacist. My w.machine has drainage problems, and drain pump stucked by rust/waste particles. I have test it by test mode, identifying problems and clean the pump. The machine is fully ok now. Thanaks for your Videos.

[@rickgoodyer3886]

Thanks for this demo my machine stopped working after a power cut while mid cycle and would not turn on to any new program after. After running through the test program as you demonstrated it worked perfect again.

[@christianbilien1653]

Thank you very, very much from Paris. Because of your chrystal clear explanations, I was able to diagnose the washer motor was not working, which led me to a faulty connector on the front panel. Works like a charm now.

[@dennisbentley9242]

Just to say thanks for the info, just saved me buying another washing machine very good and easy to follow, solved at the moment and seems all working fine.

[@How-to-repair]

I'm glad I was able to help you just remember to Mark us down to your favourites. As you will never know when an appliance fails it also helps us a lot, if you can share the channel @dennisbentley9242 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@kevingronemeier6954]

Amazing tutorial sir. Best video I have ever seen, very thorough and knowledgeable about the tasks that you are explaining. Well done, sir.

[@How-to-repair]

Glad it was helpful! Kevin Gronemeier this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@evertonffrench7823]

I'm watching from Jamaica 🇯🇲. Very helpful.

[@kumardigvijaymishra5945]

Thanks for clear and detailed information on diagnostics mode of washing machine

[@How-to-repair]

You are welcome mate. Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@suncanabilic9033]

Thank you so much - the video is very useful! Every step is well explained so it is very easy to follow the instructions.

[@How-to-repair]

Glad it was helpful! Thank you for leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@scotsiain1970]

Good video, just bought a Samsung series 5 washing machine after our indesit washer/dryer broke. Samsung allegedly reliable so we shall see.

[@جراح_الغسالات_الاتوماتيك]

Good luck and success to everyone Al-Jarjawi, automatic washing machine surgeon

[@aerosoapbreeze264]

Excellent. Clear and Concise. Thank you !

[@carolo6412]

Excellent video - very helpful - any idea how to stop or what the cause of a musty smell in an empty Samsung 8kg (2016) washing machine.

[@darryldenoon6067]

Best Samsung washing machine video, thank you soooooo much!

[@ElRicardo81825]

This video is legendary!!! Extremely helpful!! Thank you so much! ❤

[@mahmoudazzam536]

I have Samsung w m echo buble 10kg.could you explain how to go through the test on this model please. The buttons on mine are not the same as in your video

[@fob3664]

This video is absolutely fantastic, thank-you so much

[@Salaar_tours_official]

Thanks, followed ur instructions, comes up on fault.

[@maheshmunaweera4476]

Thank you so much sir It’s very helpful program to fixed my issue and you doing it very nicely so that very helpful thank you ❤god bless you ❤❤

[@How-to-repair]

You are most welcome and happy to help mate! Could you do me a favour and take part in a poll I've made about the lifespan of appliances? You just need to tick one of two boxes. It will only take about 10 seconds. This might help us improve how machines are made in the future😇 Here's the poll question: www.youtube.com/@How-to-repair/community Also sharing will get more people to participate and we will have a greater impact with the manufacturers thank you for helping.

[@shafimehar4506]

Hello sir good day to you.your video is really mind blowing. Superb.Thank you sir

[@melquesedekcastro7480]

You're simply great the way you explain things. Congratulations sir.

[@tomlong4385]

You're video just helped a ton.. thank you for sharing 👍

[@How-to-repair]

Glad it helped What would really help me to get my video seen as I'm no IT expert is to either share the channel or at least post it to your friends my videos might not be KZbin superstars, but they save Appliances from the scrapheap. Share and help us fight appliance waste! @tomlong4385 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@monah1263]

Can I do this to my Samsung washing machine Schaumaktiv 7.0kg and I don’t have ecobubble

[@catalinaorianagonzalezratt6550]

Hello! Thank you for your video! I have a Samsung washing machine model WW70J4463GS but it doesn't have the same buttons. From left to right, they are "temperature - spin - option - delayed end - bubble soak". Could you please tell me which ones I need to press to enter the washing machine's diagnostic test?

[@tommylou7169]

Very nice to know. Should do more with other brands. Thanks

[@How-to-repair]

I will be doing a lot more of these in the future @tommylou7169 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@jacksonblack9408]

For Australian machines it's pretty similar, only you hold buttons 2&3 when powering up

[@unblackdawn1134]

On german machines too . Thanks dir the comment M8 😊

[@jh45411]

Not getting any help

[@johnmizzi1266]

Great, very informative, many thanks.

[@jagathwarnakulasuriya554]

Thank you very Mach, good explanation.

[@bigbirdpukindog]

Do you have a video on how to do diagnostic videos for the Samsung dryer model DVE45T6000W

[@davidmeadows4299]

Thanks for the informative video. I have samsung Ecobubble digital inverter ww10n645rbw. The machine is not heating up. I have checked the element and thermostat with a electrical tester and they are ok. My pcb was replaced some years ago and I swapped the current one with the original one (which was ok at time), still no heat. I have run the diagnostic test (from the delayed start proceedure) but I am not whether I hear the element coming on during the wash cycle test. The simple diagnostic test shows no error. I am at a loss. Any thoughts? Do you stock the pcb's if it that? Many thanks

[@How-to-repair]

Hi David, I've created an FAQ page for you. You can find a detailed repair guide for your problem on this page. I suggest you start by getting a smart multimeter and testing the heater, NTC sensor, wiring, etc. Here is the link: www.how-to-repair.com/faqs/samsung-ww10n645rbw-washing-machine-not-heating/ Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ 😇 Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@voyac]

Wonderful! Thanks for video

[@How-to-repair]

Thanks a lot for your comment mate. Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/

[@MARS-GREENH0USE]

Loved you in aliens3 thanks. But my machine stops in spin and powers off and on forever, i took off the crappy plug splitter but now it still beeps there without finishing. Cant figure it out still. Thx

[@hayleysainsbury3756]

It worked perfect thank u

[@How-to-repair]

You're welcome mate! Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ Thanks 👍

[@saverioautore2358]

Hi, congratulations for your videos, very clear. I have a question for you, I have a Samsung washing machine with DC error. There is 220 volts on the door lock connector, I replaced it but it still shows the same DC error. I noticed that the 220 volt is present on the connector only when empty, i.e. without the door lock connected, if I connect the door lock the 220 volt is no longer there. What do you suggest me? I'm thinking of replacing the board, but it costs a lot and I would like to limit the risk of making a mistake.

[@ashrafatef-f1m]

thank you very much that video help me to fix my machine

[@devaratnam1421]

Very well explained, thank you for the great video.

[@janice3608]

You are wonderful. Thank you for your thoroughness.

[@How-to-repair]

Really glad it helped you fix your problem Thank you for leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@MateTransportGameplay]

Can you show how to start the manual service cycle on the Samsung WW60J4260LW?

[@outlawmorga]

Great informative video. I have error code UC, it’s intermittent and seems to appear half way through any cycle. I haven’t been able to pin point at what point the error code appear. Any idea?

[@carolo6412]

How do I run a service wash - EcoBubble 2016. Thank you

[@singh2007mahendra]

Thank you so much your video it's very helpful 👍👍

[@How-to-repair]

You're welcome! I'm glad it was helpful. glad we could help you @singh2007mahendra this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@andrestobar530]

Thankyou good Sir

[@How-to-repair]

So nice of you mate. Please remember to subscribe to our channel, as that really helps us 😇 Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/

[@jmcerezoreyes]

Hi, I have a Samsung eco bubble 7kgs and I get error 4E. I have cleaned the water inlet rubber that was clogged and it is now taking water, but the error still appears. What can I do? Thanks

[@annadurai9630]

Excellent sir

[@How-to-repair]

Thanks for your comment mate.

[@Bob_too]

Many thanks - mine does not go to tSt when I get to the part Rotate the program Left - instead it goes through the numbers and then goes to: 4C-OE, 80_ _80, 254, then finally UC and sticks there. It’s the older non inverter model. Any ideas ? In general I have the Random Pause problem when running programs and have an occasional 3E code, but am changing brushes in the next few days.

[@masoudmontazery907]

Good luck sir 🎉

[@srinivaskosuri3932]

Vry useful video thnq vry much sir

[@How-to-repair]

Glad it was helpful! Thank you for leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@rickyhutchings2263]

Hi there our ecobubble just comes up with dE could you tell us what that means thanks

[@How-to-repair]

Hi mate, this normally means either the door is not shut correctly, you may have a problem with the latch mechanism, or you may have a problem with the door interlock, which means changing. You can watch this video to learn more about the problem and to fix it: kzbin.info/www/bejne/mnPFiWuHa6uFnLs&ab_channel=how-2-repair.com Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/

[@rickyhutchings2263]

@How-to-repair thanks mate i got sorted now the wires had come off the door latch thanks for the reply 👍

[@fwmkoobmoua909]

Thank you very much.

[@oay6702]

Thanks you a ever so much, your video was so helpful ❤❤❤❤

[@How-to-repair]

Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. kzbin.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@BethBodino]

My unit ecobubbles model # WD75K5410OW/TO There is red error code like square with positive sign at the upper right corner, what does it means? Am from Phils..

[@michelle-bx6ji]

my washer stops on the spin ,can you help please or should i buy one .thank you

[@MikeCarter]

Mine too. From watching videos and reading around it appears to be caused by the PCB needing replacement. Was it intermittent stopping on spin cycles or every time on any wash programme?

[@rodneysijp2343]

Do you also have a video how to fix a LC1 error on a samsung washing machine?

[@How-to-repair]

hi LC or LC1, are we needed to drain pump issues? I have done lots of videos on drainage problems on washing machines. I suggest you check the pump the sump hose and also the waste fittings going to the appropriate connection that you have basically this error is saying unable to empty in the allocated period of time this is why you are getting these error codes @rodneysijp2343 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@hassanplombier3442]

thank you for this

[@stiaanroodt86]

Hi just want to find out if there is a test with the washer dryer testing the dryer heating side of thing? Great video thanks

[@How-to-repair]

not yet sorry Thanks please remember to subscribe as that's is was keeps this channel going. Thanks 👍

[@joaocoelho7331]

Excellent tutorial!!!

[@How-to-repair]

Thank you! @joaocoelho7331 please remember to subscribe to our channel as that really helps us kzbin.infoe432SAb2g08 Thanks, Paul 👍

[@raymondwheatley2796]

Hi We have a Samsung eco bubble with 5E. After 50 mins on quick wash the display reads 5E so we power down and power on the machine turn it to rinse and spin it runs to the end no water in the bottom of the machine so I cleaned the filter out removed the pump all looks good but you can’t rotate the motor no more than one revolution either way not sure if that’s right re assembly tested again same thing after 50 mins 5E also learned the waste on the sink trap. Any ideas. Thanks Ray

[@kumarmukesh2398]

Very interesting 👌

[@ethanMonoP]

Great video thanks!!!

[@Polskitime]

Thank you . Can i also change end song in the machine?

[@sebekuk]

For me, it shows an error 3E2, can you specify whether it will be an inverter motor or PCB? thank you

[@quaidkhan5072]

Nice vedio. my ecobubble stop in the middle of the cycle without appearing any error?

[@RRUKGhost]

Hello good sir, great video. I’ve done all the steps and the washing machine appears to be working correctly. However whenever I try and run an actual cycle, it stops after 1 minute, I’m perplexed. Any ideas?

[@Este974]

Same problem!! Any news about this problem?

[@thes9220]

I have very similar problem. Machine fills up with water, but after when it come to spin, it stuck. Machine is not under or overloaded. Not heavy things inside. Any thoughts people?

[@MKasap-te8vm]

​@@thes9220did you resolve the problem? What was the cause of the problem?

[@JohnSmith-t1x]

How do you run a diagnostic test mode on model WF419AAW/XAA01

[@How-to-repair]

Hi, please use our contact us page and make sure you fill out the request for what your problem is. I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@clintbolan3112]

Hi from France. I'm the owner of a SAMSUNG W0804Y8E/XEF washer. I tried to run the diagnostic mode as you show in your video but when I push the same buttons as you to enter the mode the result is not the same and I have not the TST mode appearing on the screen. Can you tell me where I can find the specific process for my washer? thanks a lot.

[@rayonbay4090]

Samsung ecobubble washer dryer.when using dryer synthetic or cotton programa, machine letting water in and out,and after min shows 5C .what's wrong.

[@kykyryky5013]

Hello, thank you for video. I've checked my machine and everything seems OK, but it isn't 😢 heater works (~9A current, water temp increases) , both pumps working well, water level sensor frequency changes accordingly to water level (higher level lower frequency), spins both sides till forever. But during washing cycle it stays looong time without anything in blinking main program indicator (two vertical lines in bath). Sometimes in 15min, sometimes in 60min it starts and continue. Sometimes it happens more time during one washing cycle.

[@How-to-repair]

Hi, I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@zaczac3024]

Note: to enter test on non ECOBubble machines, press and hold middle two buttons (Rinse & Spin) then press Power on button

[@jacquesb5248]

dude you might just save a lot of money. sadly 3C error is back when i diagnostic mode. cant even go into the test mode anymore just getting :- _ icon

[@kabsgerry]

You are awesome

[@demetrismit3090]

Great videos. Can you do this on a top loader? Mine is a 13kg, it is about 5 to 8 years old. There is no dial. Thanks!

[@ch1809]

Hi. I have one of these washing machine that is not working. Don’t need anymore. Do you want to pick it up? I thought I would ask before throw it away.

[@nyoytorio4167]

Wow thank you

[@robertopavan2819]

Good evening, I have a Samsung WF80F5E0W4W washing machine, sometimes it stops, the display stays on but the remaining minutes of the wash do not go down, generally it stops at 50...53 minutes remaining and it doesn't unlock unless I turn it off and restart it, sometimes it gives me 3E error. I checked the motor brushes and they are good... they will be about 2.5cm long. Do you think it could be a problem with the card? Thank you Roberto

[@How-to-repair]

Hi Roberto, I've created an FAQ page for you. You can find a detailed repair guide for your problem on this page. Here is the link: www.how-to-repair.com/faqs/samsung-wf80f5e0w4w-washing-machine-stops-gives-3e-error-code/ Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ 😇 Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@paulmccarthy-brain9131]

Excellent detail - thanks

[@How-to-repair]

Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. kzbin.infoUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm and this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@thankachanyohannan5159]

Very good video sir.

[@How-to-repair]

Thanks and welcome Thanks 👍 for watching and please remember to subscribe to the Channel as that's what keeps us going in able to make the video for you

[@ziofrascaccia24]

Hello my washer pauses mid cicle without spinning and then pauses itself. Also is not able to do a spin cycle unless is at 400 rpm. If i go into diagnosis mode i get this "-:". Do you have any thoughts?

[@helinshevchuk5037]

Hi, did you find an issue? I have the same problem

[@1989bartek89]

Thanks for this movie! When I try to enter this mode I become only " -: " sign. Does it mean the PCB error? Should it be replaced?

[@How-to-repair]

Without having the washing machine in front of me, it is very hard for me to actually say with honesty, what the problem is, as I do not want you to go buying a new circuit board and finding that is not the fault

[@Leo-gt1bx]

What possible causes are there? Can the door lock cause it? Machine keeps powering off.​@@How-to-repair

[@horacepinto8965]

Hey I got a question what a( 3e1) I was doing the tst on my Samsung mich

[@How-to-repair]

Hi, please use our contact us page and make sure you fill out the request for what your problem is. I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@anthonybaxter808]

Hi quick question I have the same machine all tests are fine apart from it doesn't turn while washing spins fine tho

[@How-to-repair]

It will depend on what model you have as there are different variations in motor. If you have a motor with carbon brushes, I would inspect them or if you have a motor that does not have carbon brushes then normally this will be a problem with the circuit board. Have a great New Year and please remember to subscribe to the channel. glad we could help you @anthonybaxter808 this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍

[@Bigguy938]

Hi I've got a samsung bubble wash and 8.5 litre just doesn't want to spin just beeps any Ideas what going on

[@JezClark-j6v]

Hi, I have run the tests and all seems to be in order. Our problem is that the drum starts to empty before it reaches the seal when the drainage pipe is laid out on the floor. We have to raise it manually when this stage is happening. We therefore have to lower it manually when it reaches the drain cycles. We litererally have to stand over every wash lowering and raising the drain pipe on 5 different occations per wash. We recently moved and this has happened since then.Please help, I am at my wits end and do not know which way to turn :) We have run the re calibration mode.

[@How-to-repair]

Hi, I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@margiesedillo7771]

Hello sir how can unlocked Al Ecobubbles washing machine (samsung).i appreciated it if you can help me.thanks

[@janetwanjiru2013]

How do I reset my Samsung diamond 7kg drum washing machine Kindly assist

[@AJ-tp5qj]

Hi i have the same washing machine the issue am facing is that the buttons on the dash stopped working ecept the on/off play buttons so i can actually use the washing machine but cant adjust ant of the cycles (spin , water temp..) any pointers would be highly appreciated Note: Child lock is not on :)

[@customerservice528]

What brand/model are the built in multimeters that you use? Thank you

[@How-to-repair]

these are the digital ac 50a ammeter i use they come in many types and colours ebay.us/FC2Wgf this is an affiliate link so I will win a small commission off eBay I hope you don't mind. and this a message for leaving a comment Thank you For leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@WilliamGacquer]

Thanks a lot!

[@How-to-repair]

Glad it was helpful! Thank you for leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@NikNastev]

My Samsung WM EcoBubble WF70** have error code 3E. I did a latest test (4) from TEST procedure, where motor spins on both directions. Motor start to spin on first direction just fine, but then when it needs to switch direction of spin - it's stops with 3E code. What could be the problem - Motor or Electronic? I mean - what to look as most possible issue? As motor spins normally in one direction and pass all 3 tests, before test number 4. Thanks!

[@gilbertoalgarra491]

Great video, my machine is not running and I can’t open the door . Help

[@jh45411]

Hi turning my Samsung machine on immediately the error code comes up so it will not let me put it in diagnostic mode what do I do we've put in two temperature thermostats already the error code is TE

[@DrColg8]

Recalibrate after the repair and give it a try. The error memory may have to be cleared to recognize the new sensor

[@amarveeravalli6163]

Getting error 4c in some programs like baby care ,denim etc and not getting error in quick wash and rinse and spin programs, what it means and how to solve it

[@tomasdesouza2847]

What a great video! Thank you very much! Running the tests I discovered my EcoBubble is not turning clockwise, and that's probably why it's stopping mid-cycle. Now what to do with this information? :)

[@tomasdesouza2847]

It also ends the test with an 3E message (call customer service) but no message appears in normal mode.

[@How-to-repair]

not sure what you mean Thank you For leaving a comment this is for you kzbin.infoe432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍

[@margiesedillo7771]

Hello ..how to unlock the Al Eco bubbles?please help me.thanks

[@rbmwiv]

Thanks

[@najbekkers]

Hi, my machine wont go into test mode. Also the balancing mode does not work. I can turn the machine on and can select a wash but when I press play it makes the sound that it is starting, but nothing happens. Can you please give me some advise what to do? Thank you

[@How-to-repair]

Hi, please use our contact us page and make sure you fill out the request for what your problem is. I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. A video shoot of the problem would be perfect as well. Normally, I would get back to you within 24 hours but I am on my way back from the IFA trade show in Berlin, so it can take more time to respond. Thanks for your understanding. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

[@tomasjanssen4863]

Hi. How do i enter test mode on the WW70TA049AE ?

[@JaninaProgresa]

Hello, please advise. I have a washing machine eco bubble 7kg / wf70f5e5u4w. The washing machine began to jam, as if it did not have the strength to turn the drum. It is interesting that it could only be washed on 3 programs - hand wash, wool and spin. All three work without a prewash and it worked for a few days. Now the whole program, this short one, and the spin cycle are no longer running. I observed the washing machine and I really think that the motor runs quietly, the water fills in, the pump drains ... the fault is really mysterious. After loading the smart apps - it says ˇThe motor rotor was diagnosed as locked" So there is a question? is the problem the motor or the motherboard? Thank you very much for your opinion :-)

[@zeinalabdinsaker9301]

Sir I have Samsung Washing machine ww70j5. Its display flashes with only number 8 but it will not turn on. Could you help me with that please?

[@craigwoodburn4436]

My research on the internet leads me to think I have a common problem with my Samsung Bubblewash WF1104XAC XSA 03 front loader washing machine. When it reaches the spin cycle the drum spins very slow one way then stops and spins very slow the other way like a normal redistribution cycle, then once it reaches 9 minutes left it stays on 9 mins for ages. If you come back in 20 mins it will still say 9 minutes and the drum still is spinning very slow. Its like its still washing not spinning. No fault errors come up and eventually the timer starts counting down again, but still does not do a high speed spin. I did you a spin test using your video thanks and it reached 1320rpm. I've checked the drainage pump and filter of course and all seems good there. Plenty of water getting pumped out. I was wondering if there's a two stage door lock on my model that I've heard can prevent high speed spin if it's malfunctioning. That would be strange though since there's no error. Do you have any ideas you might be able to suggest please? Thanks!:)

[@craigwoodburn4436]

I just had a look at your website and I'm now wondering if I should check out the pressure switch and tube next...

[@janbryja1889]

@@craigwoodburn4436 hjj

[@janbryja1889]

@@craigwoodburn4436 hjj

[@wandochadventures4696]

Any luck I have the same problem

[@kirstyhyatt7132]

Sounds similar to our problem and we have a bubble wash, I will try this and look at a few other options when the kids are asleep because I can't get the kids to stop touching whilst I am trying tgis