Thank you for posting this. It was pretty easy to replace the suspension rods by watching your video. Washer working great now. Many thanks, sir.
@dawnlemon990 Жыл бұрын
Really helped me, I was able to replace the shocks by myself, but didn’t know I had to recalibrate the machine! Many thanks!!
@Chesternut0072 жыл бұрын
This was an awesome video. I had gotten to the part where the lid needed to come off and you had reached the same conclusion I did. I said well crap at least I knew not to keep searching for a way to disconnect the whole lid. Also the calabration hot keys was a good tip as well
@matthewstreet-d2hАй бұрын
My washer was throwing this alarms every time, so i ordered new rods and going to give this a shot, Ha wish me luck
@crifix.Ай бұрын
When I replaced mine it looked good first 3-4 loads
@robc3793 Жыл бұрын
Wow thanks for your video Had a professional come look at it and they said 800 to fix I did it less than a 100 thanks to you Thanks you saved me a boat load of money
@bakihanma724716 күн бұрын
How's those cheap suspension rods holding up after a year.?
@crifix.16 күн бұрын
@bakihanma7247 not so much
@bakihanma724716 күн бұрын
@@crifix. You think the actual Samsung brand will do any better?
@crifix.16 күн бұрын
@bakihanma7247 don't think so
@Leafy5972 жыл бұрын
It is such a shame, these washers can't be more than a few years old and are already having problems!
@crifix.2 жыл бұрын
Mine lasted 2 days...lol
@jeffsvad Жыл бұрын
Really wish this video showed how to get the main control panel off instead of just still pictures after it has been removed. I removed the screws as shown, how do you actually get it to disconnect from the part that is closest to the lid?
@leonelcruz29 Жыл бұрын
I change the suspension rods and did that calibration and it still going out of balance on the last your video you said you did some adjustments can you tell me what you did
@crifix. Жыл бұрын
Make sure the washer is level
@alfonsoramos3777 Жыл бұрын
He had to balance the load himself. He had to open the lid and readjust the clothing’s positions. Not a good solution to the main problem.
@davidalfaro4749 Жыл бұрын
Thanks nice video 👍🏻
@jrg.882 ай бұрын
Ub 1:13:30
@fammartinez57722 жыл бұрын
Could you link the website for the ones that you purchased? Thank you
@aidanalmeida2 ай бұрын
Unbelievable. It quickly moved from balanced to unbalanced.😮😬😐
@franciscorubio7226Күн бұрын
How you know which spring is failing?
@crifix.Күн бұрын
I test pushing the basket by hand and it wobble a lot
@natashakelly24682 жыл бұрын
I have the same washer, after removing all the same screws the control panel still won't come off it seems to be stuck at the back- the part that touches the lid. Did it just come off or did you have to apply a little force?
@crifix.2 жыл бұрын
There should be clips on the side
@nickyjackflash2 жыл бұрын
@@lisaannh.y.357 there are three screws that connect the display face piece to the motherboard piece on the top of the washer. I unscrewed those and unhooked the two electrical cable/ribbons that connect the two pieces. This gave me more of an ability to move the lid. I did not completely remove the lid. I was able to lift the lid up safely at a 45° angle and maneuver the rods out and replace them.
@jrg.882 ай бұрын
Banging 1:13:00
@crifix.2 ай бұрын
Lot of banging...lol
@jrg.882 ай бұрын
I have the same washer
@franciscovenus313 ай бұрын
For this Teste
@marktraver6796 ай бұрын
Nothing like starting in the middle😂
@MichaelRobinson-gz2kj3 жыл бұрын
Crifix, hi, can you show the whole world how to enter the test mode on machines like this?
@MrCwhitt752 жыл бұрын
Make sure the washer is empty. Power it on and hold down temp and delay end simultaneously. Your display will change then just hit start. Takes about 2 minutes for test to complete
@oscarguevara12372 жыл бұрын
@@MrCwhitt75 you’re a hero sir! May god bless you !!!
@SamsungSmartWashingMachineFanАй бұрын
Test cycle: Turn on the washer. Press Delay end till it shows “17h” and hold start till AS appears then press start
@appliancealliance44442 жыл бұрын
I hate to say it but you may have a drive system problem if your tub is still bouncing after replacing suspension. Possible inner tub problem which is bad news for the machine.
@appliancealliance44442 жыл бұрын
The other thing I’d check Is if these “new” suspension rods are OEM Samsung not cheap amazon aftermarket. I also heard you’re supposed to use dampening grease on the bushings of the suspension rods.
@mandy2tomtube2 жыл бұрын
The video lose me a bit confused I appreciate you posting the whole process but it seems to have gone out of balance pretty quickly even with the new springs I’m having the exact same problem with the exact same machine not sure if I should try to replace the rods or just get a new machine?
@crifix.2 жыл бұрын
After few tries it works better. But sometimes still go out of balance
@jrg.882 ай бұрын
4 1:22:00
@ivanroman751410 ай бұрын
This is exactly the same issue that's repeatedly happening on my Samsung WA14J6750SV Top Load Washer with Activ DualWash 14Kg
@crifix.10 ай бұрын
They are very sensitive to unbalanced loads
@rosejangmitv13154 ай бұрын
@@crifix.dude it says ur
@lightningsrt47072 жыл бұрын
Why would not show how to take off the control panel.
@lisaannh.y.3572 жыл бұрын
That is where we are stuck as well
@nickyjackflash2 жыл бұрын
See my reply above. I just finished the repair 30 minutes ago.
@rock-vj5vr2 жыл бұрын
1:13:22
@jeremyparck5649 Жыл бұрын
Those arms though
@nongeath69983 жыл бұрын
1:13:30ur
@lecanas12 жыл бұрын
What's the point of this video! To watch a washer run a full cycle! I was expecting to see how to replace the dampers!
@crifix.2 жыл бұрын
If you watch the first 5 min of the video that's what I do....Questions?