Waste oil distillate fuel - ethoxide cleaning, odor removing.

A method of cleaning and odor-removing distilled WMO-based fuel.
This method uses some easy-to-get reagents, ethyl alcohol (sold as methylated spirit), sodium hydroxide (caustic soda, drain cleaner), silica gel (cat toilet crystals), plus water. No need for sulfuric acid or poisonous methanol.
Contact: [e-mail]
Website: www.ferromit.com/index.html
WMO still construction plans: www.doubloonbay.net

[@marciofernandobarci]

very good recipe to make biodiesel. I'll dare suggest you can add to process - using quicklime instead silica gel to dehydrate final stage. In Brazil - before our national alcohol project (for fuel) when high technology were developed, the production of dehydrate Ethylic alcohol was done by quicklime. I believe 100 or 150 g of lime might be enough - try it. Congrats to you

[@maciejc.617]

Hi there :) 1. I hope the tank and pipes you are using are not made of aluminum but stainless steel, because aluminum and its alloys will corrode in contact with NaOH. 2) NaOH is a strong base, "rinse" the oil with one liter of water will not remove it, it should be neutralized with some acid imho. 3) I think silica gel absorb water, but with NaOH, so it should not be dried and reused. 4) Dissolving NaOH releases a lot of heat, which may cause the solution to boil and splashing it around. In general that is interesting video. 👍🏻

[@santeryi9]

The tank is stainless steel, the NaOH is in miniscular amount reacted with alcohol releasing the heat, so added to the fuel cold with no exothermic reaction, then it reacts with tar, settles and drained, washed and drained again, copper stripe test or water extract test is done upon the use, the used silica is mixed with NaOH again and boiled with a bit of water that turns it to sodium silicate, then dirt collected from the top of solution, later sodium silicate is converted to silica gel again. Also note that if any NaOH would be in the treated fuel, then silica gel will react with it and become neutral sodium silicate, so there is no alkali in the fuel.

[@PotatoesAssistant]

This whole process seems similar to how biodiese is made from waste cookin oil except normally methanol is used instead of ethanol, and it’s heated before being added to the waste oil

[@GuiFalked]

I'm going to have to think this might make a nice way to clean up some types of homebrewed biocrude as well 🤔

[@nwzz]

Hello, thank you so much for this video, is it possible to get more details, qty , concentration of alcohol etc ? Regards,

[@hayden6930]

This is great, just discovered your channel. I run only diesel vehicles and collect enough waste oil to power my vehicles even with an 80% recovery rate through distillation. I've been wanting to have a go at cracking it for the longest time. It seems like the addition of a centrifuge could be quite useful at a variety of stages in the cracking and refining processes?

[@santeryi9]

Yes the centrifuge at the final stage would be a great addition.

[@hayden6930]

@@santeryi9 have you considered using waste gas or light fractions as the heat source for the still? I imagine that would come with risks, but the reduction of electricity demand seems possibly worthwhile?

[@hayden6930]

@@FirstLast-tx3yj I personally have no use for petrol/gasoline, so that wouldn't rank highly in my priorities. I use a bit of diesel though. I'm yet to attempt any of this. One of these days ill get there.

[@bacemkbiri8877]

Do you process it before putting it in the car's tank

[@incandescentwithrage]

Just run filtered waste oil in an iDI. The only step.

[@ljprmc]

Has the waste oil distillate shown in the video been produced with the home made still as in earlier videos ? Or is this process a direct treatment of WMO into a clean WMO for blending into a diesel fuel alternative ?

[@hydrocrow1108]

Since its referred to as distillate.....

[@dubstepTonme]

Respect to Avidyne/Aspen for stepping up with a glass panel. This is going to be brilliant.

[@wazza33racer]

so is the WMO just filtered waste engine oil, or has it been distilled by heat?

[@ft.j.gdhjjdhfgjk7248]

كيف نتخلص من اللون الاحمر وهل سخنت الخليط في المراحل الأولى ام فقط في المرحله الاخيره

[@SyrianBiodiesel]

Hi, I would like to tell you what I do when drying biodiesel. After raising the temperature, I turn on the air for 15 minutes and all the moisture will evaporate quickly.

[@santeryi9]

Good, I am not running air after the heating, as there is some silica gel and other deposits at the bottom, just do not want them to float around.

[@user-mo1dl6pq8c]

اسیدبزن

[@theaussienurseflipper.8113]

G'day mate, does the silica gel just stay in the tank? And you drain good fuel out thru it, cheers

[@MrMraza123]

Excellent video.

[@guillermoibarra7969]

Awesome Alex!!

[@santeryi9]

Thanks a lot.

[@krithicks6206]

So what is use of the end product?

[@simoamd6335]

Can we used sel instead of sodium or potassium ?

[@sunilperera5553]

Thanks a great video, which not only save money, but soil pollution by WMO. I have a question. Waste oil may be containing a part of synthetic and semi synthetic oil also in it, say 30%. Would this method still valid and give a good fuel or do we need to alter the volume of silica gel/ethoxide to remove impurities?

[@abbasvaliya4646]

.

[@cmte.brazinazzo2061]

I tried, Polyether Amines TEPA, and it also cleans the fuel. It sequesters the dirt. Getting a thick black goo to the bottom of the container. But it take 2 weeks to do it.

[@santeryi9]

with this method the black goo drops in 30min.

[@christopherleubner6633]

Sodium ethoxide can be prepared in two ways. By reaction of sodium metal in ethanol, or by electrolysis of an anhydrous solution of NaOH in ethanol at high current.

[@danbrown935]

That’s great if you’re retired. A lot of work to get setup. Great video thanks

[@saadjaved4274]

Hi, is there any chemical which can be used to adjust the ph of waste engine oil before distillation to avoid thermal cracking?

[@davenlackey9763]

Ethanol amine

[@tek4]

Acids and bases

[@tomayrscotland6890]

would it not be better just to buy red diesel if locally sourced.

[@ryanpoe3054]

Do have a product buying link... where can you buy that stuff

[@KashifAli-mm5ox]

pyary bhai yr btaa den gye ap kitny litr me kitna graam chemical dalna chahyie ..10 litr ho to

[@coachgeo]

would it be beneficial to do this with raw wmo to get as much yucks out of it (aka..... less to filter/centrifuge cause it fell out via this process) prior to distilling to a diesel fraction?

[@johndowe7003]

You could but from what I gather is that a lot of mess forms at the bottom and lowers efficiency and makes things more dangerous

[@coachgeo]

@@johndowe7003 that is my point.... only centrifuge what is above the settlement. will then take less centrifuge passes to get an oil that is more uniform... thus will crack easier and cleaner as you distill it.

[@ppphhhh131]

Is this reclaimed base oil and how to clean more and make it bright yellow golden

[@santeryi9]

In my case I use it as fuel, so no real need to make it bright yellow, bur I would recomment to store it with silica for longer period of time and it will become bright yellow in week time, so some absorbent will do the trick.

[@diyoffgridcountrylifeaustralia]

Hello great video i was wondering what grade of silica gel is it the same a desicant silica

[@santeryi9]

Yes it is

[@johntexan4165]

do you have to use the near 100% Ethyl, or can you use the 70ish% ethyl rubbing alcohol? Huge price difference. Ever tested it?

[@santeryi9]

I use 90+ you can try 70% why not?

[@kishorashish7327]

How can i remove oil from water in waste water and cooling water with Chemicals Treatment..? Can you guide please

[@wetimkr]

Dose it smell like disel also or no?

[@LB-vl6qo]

Does anyone know what the specific gravity of the oil was after distillation? 831-833 is ideal. The sulfur content remains, it destroys more modern engines.

[@Failure_Is_An_Option]

Does nothing to any engine. Emissions systems...

[@freedom_aint_free]

You probably is getting something other than ethoxide: CH3CH2- as sodium hydroxide in spite of being a strong base is not strong enough to generate ethoxide the reason being that the ethanol is a extremely weak acid, and in order for it to react like one you need brutal bases: metallic sodium (particularly in aprotic solvents like THF) is a good one, I guess you could use Lithium from batteries too. diluted acidic potassium permanganate (say in diluted sulfuric acid) can be also used to oxidize some impurities and you can clarify the colloidal suspension of MnO2 with sodium sulfite afterwards..

[@mickwolf1077]

You got yourself a sub, i gotta try this. Been collecting wmo but to use in a conara im going to modify but if i can put it in my landcruiser that'd be great.

[@santeryi9]

Please note, this is WMO distillate, not a straight WMO.

[@ZarawarKhan-gs8hr]

​@@santeryi9 means u first distilled a wmo into distilled wmo right?

[@santeryi9]

@@ZarawarKhan-gs8hr Yes you are right, it is distilled oil.

[@urgentcareguy3]

Nice job Alek! I have your plans for a WMO distillation set up. Diesel obviously has a particular odor to it when burnt. WMO when burned, has a less tolerable smell. Does the process in this video change the odor or smell to more like traditional pump purchased Diesel?

[@santeryi9]

Yes, removes the odor from the homemade fuel, makes it less prominent than the pump diesel, smells more like a fresh engine oil.

[@stevengarcia8469]

@@santeryi9 please I’d like to know how much it’ll cost me to make a set up which will purifier about 500-1000ltrs in a day.

[@randybrown9706]

Can the dirty residue be used as heat source

[@jagathmadona4082]

Can synthetic oil or oil that has been mixed ie old engine oil / gear oil be used for this process as well

[@santeryi9]

Please read the description, - I am cleaning distilled oil, so if you redistill the oil mix, then yes, you can use this method for the distillate cleaning. I plan to do the used oil cleaning experiment soon, and if successful, I will upload and share it.

[@danielnashief7463]

Instead of using air compressor for mixing the ethoxide inside the waste motor oil, can we assemble an electric motor with a propeller shaft for mixing? 220 volt AC horsepower electric motor.

[@santeryi9]

Yes, will be even better.

[@clebersonsilva2642]

Ei Alek que sensacional seu trabalho tive esses problemas com o combustível lá na África do Sul quando produzi combustível com pneus, plástico, grama já a gasolina de CO2 já saí limpa .

[@got2kittys]

Que ideoma es sus? Espanol, dialect no se O portu, que yo no Saber. Only curios, Englese mi natal idioma. Gracias amigo!

[@clebersonsilva2642]

Eu agora estou no Brasil falo português

[@vedprakashsrivastava2326]

Sirji is machine ka price kitna hai or kaha milega apna address,contact send kare

[@danielnashief7463]

If we use more caustic soda or a little more ethanol, would it destroy the process?

[@MedoKojiZiviOvde]

It's better to have excess ethanol as it is a fuel on its own. Excess caustic soda, especially if it is unreacted, will cause saponification and create soap in your fuel.

[@lakshanpasindu6000]

Hi thank you so much for doing this amazing video. Good job, but can i use methanol instead of ethyl alcohol and what is the purpose of adding silica gel?

[@santeryi9]

Hi, I think you can use methanol, in my case I am trying to avoid toxic reagents, the silica is absorbs water, tar and polymers, greatly improving the final result.

[@lakshanpasindu6000]

How long should i mix sodium hydroxide with methanol?

[@jamesboline6280]

@@lakshanpasindu6000 I think you have to use potassium hydroxide with methanol (Methoxide)

[@FFsCMs]

You should be able to improve your drying result, if you neutralize the remaining NaOH (for example with some muriatic acid) in your solution before adding the silica, as silica does not work well in basic environments.

[@user-hh4ty9cr6q]

CaO better

[@Wasio212]

Hello, is it possible to get rid of carcinogenic compounds and heavy metals that enter the atmosphere during combustion through such cleaning? Have a good day

[@tek4]

Thats what your emissions system attempted to do. It sprays urea mixed with water to the point it won't hold any more, (def), and this not only sequesters the heavy pollutants like metals but cuts down the sulphur dioxide levels too

[@user-ko1ws7hd7h]

may I know what results you should get with the hydrometer? Is it required?And also do you know any alternative heating equipment aside from cartridge heater. Is it possible to use stove to hear it?. You are very skilled!👍🏻👍🏻

[@santeryi9]

Hi the hydrometer should show 830 to 845kg per cubic meter, it is a standard requirements, so all the passages and filters are able to establish a proper fuel flow to injectors, the heating can be done with a heated water jacket made around the cylindr, then you can use aa simple water heating element, though make sure that the system is opened to atmosphere, to avoid any steam overpressure.

[@nomadworld6192]

Hi, I am thinking about making my own diesel. Could please help me with some information. Where do you get the alcohol for a decent price in new zealand? Any idea for a cheap set up to produce 30-50 liters per week with an acceptable quality? Thanks!

[@santeryi9]

Hi, I am making my alcohol. Otherwise, you can use blue methylated spirits. It is ethyl alcohol (ethanol) with some die. It is usually 5 dollars per liter in any supermarket. It will be enough to treat up to 80L of fuel sodium hydroxide sold in bunnings, currently trying to complete a construction manual about a reliable system.

[@kieranh2005]

Methylated spirits are alcohol. Also try paint shops.

[@jamesleon2770]

Diesel fan here..located Australia,access to heaps of waste oil at work (mechanic)..have nearly 1000 litres of used oil stashed away Is there any pdfs or such on how to do this?

[@muhammadbaqi5899]

With the addition of several chemicals is thevoul still usabke in the engine?

[@santeryi9]

Those chemicals are just reagents to remove all the tar and polymers from the fuel, then simple water and neutral absorbent. There is no chemical by the end of the process in fuel, and everything is drained and filtered out.

[@richardrussell7740]

HI THANK YOU VERY MUCH FOR THIS FANTASTIC VIDEO.I OWN A WORKSHOP SO HAVE ALOT OF OLD ENGINE OIL.I DID EVERYTHING AS YOU EXPLAINED BUT MY OIL IS STILL BLACK.CAN I INCREASE THE VOLUME OF THE CEMICALS TO SEE IF I CAN CHANGE IT TO A LIGHTER COLOUR OR WHAT DO YOU SUGGEST I DO.THANK YOU FOR ALL YOUR HELP.

[@santeryi9]

Hi, please read the description - I am treating the distilled oil, not the black one from a sump. Hopefully, soon I will upload the oil cleaning method video.

[@siperhallo]

@@santeryi9 koniecznie

[@nwzz]

@@santeryi9 Hello Alek thank you so much for your sharing, what's the hygrometer value after 3 days?

[@hasanhuseyinkalalikalali9686]

هل تستخدم معها مصدر الحرارة ؟ Do you used thermal source ?

[@tcmtech7515]

What exactly are you gaining from this process? I've worked with used oil/waste oil for years and all I have ever done is run it through 10-micron filters to get it clean and then blend it with ~20 to 30% E85 to get diesel engines to run normally on it.

[@santeryi9]

Here I am processing pyrolysis oil, removing asphaltenes and tar that otherwise will clog the fuel system. And no need to add any petrol.

[@johnlong384]

Pretty nice and yes, you could have made Schnaps with the same efforts too.

[@santeryi9]

sure, check my channel, there are plenty of Schnaps videos too.

[@johnlong384]

10-4!

[@vacuumsetting]

Oxygen can not be used while stirring. It is a strong oxidizing agent that significantly affects the process itself and its result. For chemical mixing, it is necessary to use a rotary mechanism with a frequency converter...

[@santeryi9]

Yes I know, this is a poor man's system, planning a recirculating centrifugal pump for mixing.

[@vacuumsetting]

@@santeryi9 The fuel cleaning process, i.e. sorption of the product cannot take place in this way, it is not serious. You could take a simple funnel

[@aymansaied780]

Do you mean that the material should be thrown. and stirring. And this must be isolated from the air. Or the barrel is closed and suspended from the top by a motor with an internal stirrer

[@warrenm374]

What about a mixture of 78% nitrogen and 20.9% oxygen?

[@dexterstudio480]

@@warrenm374 thats air and what alek is using and has been advised not to

[@vasilepopescu5742]

Many thanks for sharing this tehnic with people... I m hapy to find your video! ✌️My ask is: how old car I must have to runing on this fuel!??? Many greetings ✌️

[@santeryi9]

Best for plunger type fuel pump equipped cars.

[@vikingmihinlank969]

How much does ДТ cost in your country? Will this work pay off?

[@BuenaVida-km8pu]

porque simplemente no vuelves a destilarlo? gracias

[@jimjardine4705]

is this suitable to use in a furnace to fire up for hot water boiler to heat house???

[@santeryi9]

Yes, it is suitable for furnace.

[@tishbrett]

I use use waste oil but only filtered it to use in my diesel never distilled it or added anything

[@RabbitInAHumanWoild]

Dissolving NaOH in EtOH does not make ethoxide. You have merely created a solution of NaOH in alcohol. Ethoxide is a much stronger base than hydroxide.

[@axer451]

You can make ethoxide by adding naoh to ethanol,

[@BrandonGarcia-ib3rm]

Question, why do you add the water to the mix only to drain it out 10 hours later, is there a reason for adding and missing in the water?

[@santeryi9]

I am adding and mixing water with fuel to dissolve and remove any remaining alkali, also I giving it a time to separate from the fuel and deposit to the bottom of the container.

[@johnmellor3318]

Could you please give me a list of all the equipment you use please

[@santeryi9]

I am using the oil distiller, the conical container for oil preparation and later fuel treatment, metal containers for bitumen collection, plastic containers for fuel storage, and a transfer pump with an oil filter for car fueling.

[@user-ko1ws7hd7h]

Hi! Does it have to be distilled first by heat and cool it down before I put it on the pot so I can Achieve that color?

[@santeryi9]

Yes it does! The title says "waste oil DISTILLATE."

[@grapsorz]

what do the silica gel do? other then pull some water out? do it pull other stuff out?

[@santeryi9]

Removes tar, polymers, colorings, the silica gets dark, the fuel gets transparent.

[@grapsorz]

@@santeryi9 is it possible to get that out of the gel again? like burning it out.

[@santeryi9]

@@grapsorz yes you can burn it out

[@theaussienurseflipper.8113]

Did U remove the silica beads? Cheers

[@kuripotech461]

How much did it cost you to do the whole process and versus how long will you be able to use that for whatever purpose you want to?

[@rrtsduf]

Yea... plus time

[@marchawthorne2479]

What would this fuel be used for? Thanks, I have the opportunity to get lots of waste diesel motor oil and auto oil, and used cooking oil, can I mix them together or would they need to be processed separately? Thanks for the great video

[@santeryi9]

The cooking oil should be processed separately, and the final result can be mixed. Waste motor oil should be distilled first. The fuel is for my diesel Mazda MPV 2500cc turbo diesel.

[@ghost2coast296]

Chinese street food

[@1admission]

Can diesel engine run on oily hand sanitizer? Such as hands sanitizer with aloe vera oil.

[@santeryi9]

No.

[@averagedev7768]

I would be brutally honest, when i did this i bought 2 chepest diesel fuel filters for golf 2, 2 plastic barrels and one pump. then added diesel for it to be 50/50 .I cycled 2 times the used oil thru the filters. The OM611 2.2L Mercedes engine run on it just fine without any issue. I drove at least 40 000km on that sort of fuel. I drove always long distances. The W210 rusted to the point where i cant pass inspection so i just bought a cheap w203 1.8 gasoline with lpg and forgot about the used oil thing. LPG makes me feel i am contirbuting to the cleaner air.

[@allantulli5546]

What do you do with all that waste you create? Must cost more than the fuel is worth to dispose of it.

[@linctexpilot8337]

It could be burned for heat to distill the next batch

[@kelvinsparks4651]

A very good and clear / easy to understand video, well done . Just wondering how the costs weigh up compared to diesel from the pump.

[@tonydiesel3444]

Maybe .25 cent a gal

[@tonydiesel3444]

Or less

[@juncusbufonius]

Expensive, 4-5 days, need a container big enough & stirring device. The outlay for those is high enough but in Europe those chemicals have to be bought in large enough quantities to make it cheap (1Kg NaOH == £4, Alcohol 1L £5). My time alone would make it cheaper to fill up at a gas station. And you still have to dispose of the waste materials which you need to drive to the disposal site in a vehicle. So if you do happen to have the gear lying around and you don't have anything better to do with your time then you get what? 3-4 gallons from 5 gallons of oil. That would take me a few years to get from oil changes anyway.

[@tonydiesel3444]

@@juncusbufonius recovery rate is probably ninety-plus percent fuel here is 490 a gallon so I can make 100 gallons at $0.20 a gallon you do the math machine can run at the house when I'm off of work or on days off or through the night every night of the week and maybe produced 15 gallons per run or 20 over time you will save a fortune

[@ubaidkhan3294]

@@tonydiesel3444 bro which additive use this in engine oil can u please tell me

[@mdaslam3561]

Sir cleaning one's engine oil with silica gel is a bit costly sir do you have any process which can renew the engine oil at low cost would be very helpful sir

[@captainotto]

It's only costly if you cannot reuse the silica after the process. I wonder if it can be cleaned after its used. Maybe a solvent wash then a drying would make it work again.

[@krzysztofgrzyb6095]

Fajny filmik tylko szkoda ze nie ma tlumaczenia Panie Alek Polek pozdrawiam Kris z Polski

[@mdaslam3561]

You used the silica gel once, can the silica gel tie be used again or is it only used once?

[@santeryi9]

Yes, you can regenerate it by heating to red hot state burning out all the impurities, also may add some sodium hydroxide and turn it into a liquid form of sodium silicate, dilute with water, filter, boil water out add hydrochloric acid and turn it into silica gel again.

[@MrVaneurin]

Hi Alek, will methanol work instead of Ethanol as used in Biodiesel.

[@santeryi9]

Yes, it will.

[@chrisss2630]

Hi, can be used this process to clean out some residue of waste oil for LTO burner ?

[@santeryi9]

The oil must be distilled first.

[@mercedesvan-doors34]

What do you do with the residual 'waste' products, how do you get rid of them?

[@mobmob5944]

alek doesnt use a flame but some people just toss it in the heating chamber or have a dedicated line to vaporize it and toss it back into the burner which once its going good can be so the main burner fuel is turned off and maintained by the offgass or slugdge

[@agrippanyagwaya2308]

After all the process is that diesel suitable for use in any diesel car or truck

[@santeryi9]

yes, after all the treatment it is suitable for any diesel engine.

[@brianbassett4379]

So all things considered, necessary supplies and hardware, transportation/storage of fluids, absolutely necessary clean up of contaminates, but most importantly time... it comes to what $10 maybe $15 a gallon of inferior grade fuel?

[@yootoober2009]

Is the Ethyl Alcohol a solution like the 70% solution of other alcohol?

[@santeryi9]

I use 94% alcohol

[@fatimaomoloriomolori5337]

Mamy thanks to you for sharing your knowledge. Pls how do i recycle waste lubricants oil into useful oil.. i need your advice plss

[@vijaygavarasani9137]

I'll tell you

[@usmanmajeed4256]

@@vijaygavarasani9137 please advise

[@richardrussell7740]

HI THANK YOU CAN I USE THIS METHOD TO CLEAN MY BLACK DIESEL ALSO

[@santeryi9]

No, I am planning to show how to clean the waste oil.

[@vi4781]

How do you remove the burning odour while burning this in a lamp??

[@santeryi9]

This one for engine, and this method completely removes any odor from the fuel.

[@kreasiumum]

It's a very long process, approximately what percentage of clean oil do you produce?

[@santeryi9]

Yes it is a long process, take into account that I show how to do it in a bigger volume not in a lab glass. the process can be replicated with a much bigger quantity and it will justify time spent.

[@user-uj8ip8sy4h]

а как со смазывающим свойством у такого топлива? сколько стоит инструкция по сборке мининпз?

[@santeryi9]

Топливо делается из масла, по сути это базовое масло ну и смазывающие своиства соответственно как у масла, еще я добавляю немного двухтактного масла. А так использую ка смазку для скользящих частей токарного станка, скользит прекрасно, лучше чем современная сухая соляра. Цены на новую инструкцию пока нет - инструкция в производстве, старая стоит сто америки.

[@user-uj8ip8sy4h]

у меня форсунки заклинили через 100 км после использования самодельной солярки, добавка смазывающей присадки обязательна. двухтактное масло никакого влияния на смазывающую способность не имеет, оно лишь немного повышает цетановое число, на эту тему есть результаты исследований.

[@santeryi9]

@@user-uj8ip8sy4h Если не очистить как следует и поторопиться то полимеры и смолы осядут в топливной системе, залепят клапана, форсунки, заблокируют насос, и тд. Я об этом говорю в своих видео, во первых после отгона надо отстоять, несмотря на прозрачность, сформируется много осадка, затем химическая очистка или отстой на сисликагеле, после хим очистки опять отстой на абсорбенте. если ест; сомнения то перед употреблением наливаем в чистую стеклянную посуду, даём постоять несколько часов и если на стенках посуды образуется налёт в виде тёмных точек - значит топливо неготово и в нём продолжаются процессы икисления и образования полимеров, они то и блокируют топливную систему. Все эти предосторожноти желательно делать до тех пор пока вы не найдете приемлемый для вас способ очистки топлива, в котором вы будете уверены. У меня одна машина бообще не видела соляры с заправки около 8ми лет, на самодельной наездил около двухсот тысяч километров, сейчас сын подрос, отдал ему он на ней ездит, намотала машина около 430000км, заводится и не дымит. В соляру как самодельную так и с заправки добавляю еще присадку для топлива моррейс, таким образом решаю возможные недостатки топлива. Всегда обслуживаю машину, меняю фильтры и тд. Но с дуру что попало заливатьне стоит.

[@szucslorant4115]

Hello. congratulations on a perfect and scientific video. Thanks. I would like to ask what materials can be used instead of ethanol? can it be replaced with gasoline? What should I do with the remaining excess solution that settles out? How can it be used in an environmentally friendly way?

[@MedoKojiZiviOvde]

Usually people use methanol which is far cheaper.

[@marinvremes5702]

Or kerosene, but be very careful, it's highly flammable, you don't want to harm yourself.

[@szucslorant4115]

@@marinvremes5702 Yes , Be carefoul. Thanks. here not cheapest the ethanol, its realy heavy to buy here.. or is double price .so... i need found a way to replace.

[@danielnashief7463]

How do you remove the silica gel after removing the water from the engine oil? Is it by filtration??

[@santeryi9]

the silica is in the crystal state and does not dissolve in the fuel, it deposits at the bottom of the vessel. Also, at the bottom, a fine mesh screen holds the crystals. Plus, fuel is run through the fuel filter before filling the car.

[@aymansaied780]

@@santeryi9 Is the net placed in the place of the oil exit from the inside.

[@sanduafaceri2792]

Alek why do you use SILICA GEL and from where did you take the silica

[@santeryi9]

Silica is for water and pigment removal, it polishes the fuel, also I am not always use silica, a heat drying and centrifuge filtration, my silica is from a supermarket - cat litter crystals.

[@josebotelho427]

Did viscosity change? Because I don't having a black fuel

[@santeryi9]

First distillation of wmo, then chemical cleaning, and yes viscosity will change.

[@gerrymulroy2545]

What is the benefit of this process as opposed to simply using "black diesel" , a combination of gasoline and finely filtered wmo ?

[@santeryi9]

The benefit of this process is - the vehicle's engine works the same as with the standard diesel fuel, with no smoke, no coked injectors, and no busted fuel pump. Also, there is no need for a double fuel tank system to switch from one fuel to another to flush the pump and injectors before stopping or starting the engine. In other words - one can make regular diesel fuel in a backyard.

[@keithjurena9319]

Used motor oil contains detergents, zinc compounds like ZDDP, sulfur compounds, soot, suspended metal particulates and air filter bypass dirt. These form ash in a diesel engine. This method is not as good as vacuum distillation and hydrocracking but will greatly reduce ash formation.

[@santeryi9]

@@keithjurena9319 Thanks a lot for your comment. You are right about all those additives and pollutants in the waste oil. Please read the video description, - I am treating already distilled oil. Thus all those sediments and additives are left behind.

[@rayaustria4624]

What did you use for heating the fuel?. Did you produce Disel fuel? Can you use it on vehicles?

[@santeryi9]

During processing, if I need the fiel to be warm I use a cartrige heater incerted in a stainless tube that plugged at one end, I control the temperture by suppressing the element with a voltage regulator, thus I can keep it at any desired temperature, and yes I make my own diesel fuel and use it for my diesel cars.

[@saedaldeb8399]

ماهى اسم هذه والمواد ونسب العمل بها

[@deniskangethe3718]

Can I use this process on used oil or black oil

[@johndowe7003]

Yes

[@jamesparlane9289]

can tell you are a Kiwi because you eat Anatoth jam. Do you know a recipe for clarifying used motor oil and thickening it to make chainsaw bar oil?

[@pauljohnson2372]

It looks very similar to biodiesel process

[@shajahanvmvakkathodika9665]

Can it be used as diesel if it is distilled again with a two-machine?

[@santeryi9]

Hi, this was complete treatment, and this fuel can be used as diesel. I will release second part where I fueling my car with it.

[@shajahanvmvakkathodika9665]

@@santeryi9 thanks dear

[@digitalbilly]

Couldn't you jsut do the same with Diatomaceous earth powder?

[@antoniosestar3671]

no, only silica

[@mihamaker]

Thank you for this video, this is a real treasure. Collecting WMO for some time, using all kinds of wmo burners but needed better and cleaner application. Also using cooking oils only filtered and 50% diesel mix directly in a car. No problem at all. One question, the black waste product, tar-looking, can it be used on concrete and wood for hydro-isolation or maybe distilled further into a more thick mass?

[@samirhuskic2404]

Pozz Mihovile Za koji tacno automobil koristis mjesavinu dizela i ulja? I ja sam poceo istrazivati o tome pa sakupljam info Hvala

[@mihamaker]

@@samirhuskic2404 Pozdrav, koristio sam na Renault Kangoo 2000g i Espace 2007g. Na Kangoo bez problema 75% mjesavina ali ne u sred zime. Teže pali. Kad se zagrije onda može, ali treba tada drugi spremnik koji bi bio u putnom prostoru po mogućnosti grijan indirektno sa toplim zrakom ili uronjena spirala spojena na sistem hladjenja motora. A trenutno s prekidima na Fiat Scudo 2013. Nemam vise toliko dostupnog rabljenog jestivog ulja.

[@samirhuskic2404]

@@mihamaker Hvala ti puno na informacijama,ja imam passat 5 plus i te njihove pumpe navodno ne trpe ulje,trazim neko starije auto da eksperimentisem

[@mihamaker]

@@samirhuskic2404 Čisto sumnjam. Problem je sa rijetkim mješavinama tipa lož ulje kerozin i slično. U tom slučaju na puni rezervoar bi trebalo ubaciti minimum litru dvotaktola i to je to.

[@alexdissieux5137]

​@@mihamakerbonjour 😍... vous rajouter du carburant (mélange essence-huile) ou de l'huile 2temps?

[@md.abdulahadchowdhury9256]

Super review

[@edyharun4425]

is it suitable for an engine? What is the thick level?

[@mobmob5944]

viscosity?

[@nafeanaji7927]

Do you have any plans to purify and bleach the extracted corn oil and turn it into cooking and frying oil?

[@globalnetworksupply4983]

Hi , i tried to bleach my black diesel,with this recipe, but after 4 days the diesel was still black. Can you explain me what could be the mistake?

[@santeryi9]

Did you distill it first? It was waste oil DISTILLATE.

[@globalnetworksupply4983]

Yes , it was Waste oil distillate ,after pyrolyse.but when I put silica gel, I stired it for 30 MN

[@globalnetworksupply4983]

Now using a funnel and fabrics, with silica to bleach the black diesel

[@parus1527]

Здравствуйте,пробовал серной кислотой и триетаноламином,гудрон после суток отстоя выпал но топливо все равно чёрное,в чём может быть проблема?

[@santeryi9]

После обработки кислотой отстаиваем гудрон, затем сливаем топливо с гудрона, и уже это топливо обрабатываем триетаноламином, или пробуем этот способ: kzbin.info/www/bejne/qZWwoqRvpqqJlac

[@parus1527]

@@santeryi9 после обработки триетаноламином,Я перемешал и стала жидкость мутная уже 2 дня не оседает

[@parus1527]

Коричневого цвета,ето что не так Я сделал?с уважением

[@user-ko1ws7hd7h]

6:31 is it required to leave it for 3 days?. Sorry for too much questions 😢

[@santeryi9]

Yes, thopugh you can skip the silica gel if you run it thogh a centrifuge with inline heater.

[@theliion7777]

i need formula to use it

[@MdChand-ru6bk]

Hello sir.. please say alternatives of silica gel...

[@Humbulla93]

anhydrous magnesium sulfate or calcium chloride

[@user-ko1ws7hd7h]

Hi! Can I re-use the silica gel again? And also did u heat the oil first before putting it on the pot at 0:20

[@santeryi9]

Hi, yes you can reuse silica after reactivation, you will need to bake it in furnace, make it red hot, then cool down, may reuse for a couple of times, then you can turn it to sodium silicate, remove all the impurities and turn it back to clean silica gel. Ther oil at the beginning is cold, otherwise you may risk to turn it to thick soapy substance.

[@user-ko1ws7hd7h]

@@santeryi9So It has to be distilled by heat first then I should cool it down?. Thx