3Racing Sakura D4 Xeon Anti Camber Grip Mixing Linkage - Product Review - SAK-D4831

In this video, walk over the quick install of the 3Racing Sakura D4 Xeon Anti Camber Grip Mixing Linkage (SAK-D4831).
3Racing Sakura D4 Xeon Anti Camber Grip Mixing Linkage: bit.ly/1RrmjXA
RC Mart on the web: bit.ly/1hg9ioN
RC Mart on Facebook: on. 1MrThaz
Check out the whole 3Racing Sakura D4 Build series: • Playlist
Join the ScaleFreak Facebook Community
on. 1h3yXcf
Scale Freak Reader's Rigs: bit.ly/1nqlfW5
Scale Freak Facebook: on. 1h3yXcf

[@hollywoodfresh1120]

That's a great setup you just need to make sure that you have a lot of droop that type of suspension uses a lot of droop

[@JOHNJ0HN9111]

so that's what it's for... next on my list for the d4... HAPPY EASTER TO YOU AND THE FAMILY...

[@scalefreakgaming]

+JOHNJOHN 9111 I'm going to try to get it set up a little bit tonight and play in the Studio with it tomorrow to see what it's benefits are. Just have to clean up. That place gets dirty...QUICK

[@BlackSmithRC]

Nice upgrade Joe, can't wait to hear about the benefits

[@scalefreakgaming]

+BlackSmith RC Me too! I want to play with it tonight.

[@RANGERone88]

Looks awesome but I feel like there is something binding in the back end of your setup doesn’t seem the wanna sway very smooth once you put it together! Angle of something off to stiff of spring or oil to think or a combo of all 3 again cool upgrade tho 🤙

[@aaronjones3725]

Did it work and is it worth buying

[@KuhlsResearch]

Great video. I use the same ESC. You were mentioning an additional kit to finish off the rear end conversion. Do you happen to have the name or part number for that kit? I would like to secure one myself. Also, if you’re still using the same ESC’s, do you have any Settings you’d like to share?

[@scalefreakgaming]

Sorry, I got rid of this thing shortly after watching the video's. Turns out, no matter how much I tried, I was crap at drifting.

[@solegvng4137]

Definitely great upgrade

[@scalefreakgaming]

+RcHobbyLyFe I struggled with it. Couldn’t figure out how to tune it correctly.

[@solegvng4137]

Joe Ferguson ima run into that but its a challenge 🤷🏽‍♂️😜

[@AndriusSMA]

It's very nice upgrade, you should use a super soft springs, or it just won't work when you're drifting ;)

[@NastySteve]

Hopefully you see this. I just put mine together over the weekend and I notice my shocks seemed off. There was a lot of slack an each of them. Not sure if they are supposed to be like that or not. It’s almost like the spring is too short. Did you have that problem? I haven’t seen any videos of guys assembling the shocks in this kit. Never experienced this before.

[@scalefreakgaming]

What does slack mean? As in the piston moves pretty freely?

[@NastySteve]

Scale Freak sorry let me clarify. I can pull the piston rod out until it bottoms out. I have to pre load the spring just to eliminate the gap that’s left. It’s like either the piston shafts are too long or the spring is too short.

[@scalefreakgaming]

Normally, the shaft if going to be longer than the spring. You can set the pre-load to take that up. But you can also set the droop on the arm of the car to not extend that far.

[@threemsrc6964]

Great video Joe! With the anti camber kit installed can you a single rear shock like you have in the front?

[@scalefreakgaming]

+ThreeMsRC No, it's still two. Well, in this case, four.

[@HobbyMikes]

looks like the spur is hitting the shocks

[@ruudxd1]

Looks great!

[@RCeditit]

very nicely sorted car, looks awesome to drift with! My HPI Sprint 2 runs pretty aswell :)

[@turck133]

Is this kit D4831 better than the other one i think the number is D4830?

[@scalefreakgaming]

I’m not sure. I’m so far out of the drift stuff now. I haven’t kept up with their offerings any more. I was REALLY bad at drifting.

[@scalefreakgaming]

I’m not sure. I’m so far out of the drift stuff now. I haven’t kept up with their offerings any more. I was REALLY bad at drifting.

[@turck133]

Scale Freak thanks for reply bud, i liked your all videos anyway

[@RANGERone88]

Keep up the good work tho 🚘🚖💨💨

[@YKATO871]

Hi there, Can I ask what Wt oil you used in the dampers please. Thanks.

[@scalefreakgaming]

+Laton Hunt I normally start with 30wt

[@RANGERone88]

And being a KZbin content creator you should have pointed that out and figured what was going on right in the video I noticed it right way when you went to move it because someone could be watching and look past that because you did in your video and think it find but still have a hard time drifting because there assembly was not 100%

[@voododd666]

That's a real good idea.

[@scalefreakgaming]

+voododd666 I thought so as well. I love it.

[@timdadula7664]

does it actually work?

[@scalefreakgaming]

Tim Dadula I'm sure for someone it does. I struggled with setting it up.

[@samuel_hwang]

nice

[@scalefreakgaming]

+Samuel Hwang Thanks for watching.

[@ariesr4883]

Are these products inspired by real automotive parts?!

[@THATHATSALLFOLKS]

why the hell would you even want this?

[@scalefreakgaming]

Well...that's the thing... I'm not sure. I sort of fell for the hype and thought it would make me a better drifter. Because candidly...I'm crap at it. Instead, it make the car undriveable (for me), and untuneable (for Dave). So...I just sold everything when I realized that drifting was not for me.

[@THATHATSALLFOLKS]

@@scalefreakgaming LOT OF HYPE OUT THERE

[@scalefreakgaming]

This is a super old video too. This was back when the D4 first came out. The funny thing about the D4 was that no two were tuned the same. We had 4 of them, and they all needed to be tuned different to get the same result. It was a tricky chassis

[@extec101]

for god sake stop cal all your parts "bad boy" its anoying.