Scooter Brake Fluid 101: A Beginner's Guide to Changing Motorcycle Brake Fluid

[@Trekopolis]

I said "socket wrench" during the video, forgive me. I meant to say closed-end 8mm wrench. Anyway, you get the idea!

[@gamerdan2310]

That was EXACTLY what I needed to know. Thank yiu very much for posting!!!! Simple and straight to the point. 👍👍

[@Trekopolis]

You're Welcome! ✌🏼

[@kevindarrell2504]

Thanks a milli Billy 😅 its been a while since ive dealt with brakes and i needed to because its not safe with only back brakes!!!!! Thanks again for the refresh🎉🎉🎉

[@Trekopolis]

NP! Stay safe!

[@genesowers1726]

Thanks for that! I have a 2023 Wolf Rugby 2. I just got it and it would be great to see some maintenance on them.

[@Trekopolis]

I haven't heard of the Wolf line, but they look cool! Seem to be very popular and well-built from what I read. Anything with the word Rugby in it must be tough!

[@edwardsp1916]

Nicely made and narrated video, thank you.

[@Trekopolis]

I'm glad it was useful! ✌🏼

[@Akil12480]

Simple and to the point. Much appreciated

[@Trekopolis]

Good to hear! Thank you.

[@RRRRefuelRideRace]

Great video. I guess that you have to do it on both front discs if it has two of them. So bleeding it on each side separately. Thanks for the answer. Cheers.

[@Trekopolis]

Yessir! You're correct. On the ADV 150 (US version) the rear brake is drum, not disk. In other countries they have disk front and back. There's more demand for it in other countries because people expect it I feel.

[@RRRRefuelRideRace]

@@Trekopolis I see. :)

[@mthirschberg]

thanks for this excellent and concise tutorial.

[@Trekopolis]

Welcome!

[@yt-tl8mn]

thanks, straight to the point !

[@Trekopolis]

Thank you!

[@marvinbarboza1045]

Do I need to bleed it when adding brake fluid?

[@Trekopolis]

I don't when I'm simply topping it off or adding a little. If you change it completely then yes, or if there's a chance it gets very low and causes air in the tubing, then I'd bleed them if possible.

[@marvinbarboza1045]

@@Trekopolis Actually, its just a little. so I guess no need for bleeding. Thank you brother! Deserve a subs! :)

[@RoyStevenUngKengSoon]

Greetings, thanks for the video on ADV150. What does the service manual says about replacing the Fuel Filter on the Honda ADV150? Been scouring the net trying to figure out how to do this. Additionally, a video on how to replace the fuel filter would be much appreciated haha...

[@Trekopolis]

Good question. The manual only states to inspect the fuel line every 4k, but doesn't mention replacing the fuel filter unless there are signs of fuel line or loss of pressure. Pressure at idle is noted at 38-46 psi. I'd reckon you'd need a fuel pressure tester to really know. There is a fuel filter, but it's not anything I see needing replaced unless there's problems. At least according to the service manual. I'm curious if any dealer has ever replaced one. 🤔

[@RoyStevenUngKengSoon]

@@Trekopolis According to friends and ADV groups, the fuel filter needs to be replaced every 20K as the fuel filter can be clogged. Signs that the filter needs replacing includes loss of power. Mine has been 23K, which is why I am curious to know

[@Trekopolis]

@@RoyStevenUngKengSoon I'm finding the so called service manual is very limited with information. Doesn't say anything about that. Thanks for the info!

[@RoyStevenUngKengSoon]

@@Trekopolis needless to say, I'll be on the look out for your "Replace Honda ADV 150 Fuel Filter" videos 😆😆😆😜

[@Trekopolis]

@@RoyStevenUngKengSoon Perhaps I'll tackle that one some day! 🤔😉

[@BobJones-y1c]

Good video , to the point 😂

[@remyllebeau77]

"Clean filler cap" What does this mean? Clean the cover before removing it? The part facing outside shouldn't matter that much.

[@Trekopolis]

Just in case it has any dirt or grime so none of it falls into the reservoir. No, it's usually not a concern, just threw that in there. Some bikes are filthy, especially dirt bikes.

[@remyllebeau77]

@@Trekopolis Okay thanks.

[@jodie4609]

Bless you for this . My brake fluid is leaking i dont know from exactly where I know where the resovoir is upper right hand side near the throttle it drips down near the ignition to the storage below I dont know if its the seal or near the banjo bolt Is it difficult to remove? .i cant seem to find one anywhere . Please help .

[@Trekopolis]

I've never removed anything but the top cover so I wouldn't know exactly. I wish I could provide more. Have you searched the Internet for leaky brake fluid reservoir? I looked at the service manual and there isn't much detail on that. Here's an idea: If you're not a member of this Facebook Group I highly suggest joining and posting your question there. You'll get a lot of feedback from the people who like to tinker on their bikes. facebook.com/groups/266428567756162/ Good Luck and I'm sure somebody will offer suggestions.

[@failoverflow4888]

If I let it go empty am I in trouble or can I still add and bleed them ?

[@Trekopolis]

Brakes could fail so keep the levels checked. You still can add/bleed them, but make sure the pressure is good before riding of course.

[@failoverflow4888]

@@Trekopolis thank you for the reply I will make sure to do that before I ride agin

[@travis00017]

Thanks for the video. On scooters with rear drum brakes…does the drum need to be bled or does that use a cable system?

[@Trekopolis]

Drum brakes don't use brake fluid, just a cable/camshaft that presses and expands shoes that push outward on the inside of the drum.

[@DrunkPlastic84]

I don't have an 8mm wrench or well any wrech at all. Can this be done without a wrench 🔧

[@Trekopolis]

@@DrunkPlastic84 Pliers work. Or super human finger grip!

[@DrunkPlastic84]

@@Trekopolis thank you. Why do you even need a wrench anyway?

[@Trekopolis]

@@DrunkPlastic84 Just something to deal with the fluid release valve by the brake pad area to drain from the tube. Not the top cap.

[@AB-dl1hz]

@@DrunkPlastic84 seriously how else would you get it loose sounds like you don't need to work on anything

[@Julio-bc7pj]

hi bud, easy peasy :) now i heard that the brake fluid can damage the paint, so a towel as you mention would be great. Also maybe some glove as it might burn your skin? I'm not sure i havent deal with the brake fluid. Hey i didnt watch the nfl draft, did i miss anything? take care buddy and thx

[@Trekopolis]

And remember, don't drink it cause it resembles the color of beer. That could definitely cause heartburn. 🤔😁 Actually, didn't watch the draft much. Maybe the first couple of picks. Hard to watch kids winning the lottery. (NFL) Must be nice. 🤑

[@Julio-bc7pj]

@@Trekopolis agreed

[@kiwoxgen9929]

Mine is already below the low point, i haven't open it, but maybe it require the bleeding thing 🤔 To prevent the bubble stuff It's been 4 years anyway Last time my bike goes to workshop Since i can do simple maintenance, although these break fluid kinda new to me Since my previous bike use drum

[@Trekopolis]

The process is actually very easy. You open the bleed valve and gravity does the work as you pump the brake handle slowly. Once enough new fluid has passed through the system and you see the fresh fluid exit the tube you're done. Close the valve and top it off!

[@propeticurge]

Can I just add brake fluid without having to bleed it?

[@Trekopolis]

Yep! I was showing the bleed mainly for folks who want to replace the entire fluid if it gets older.

[@propeticurge]

thank you for the response✌🏽🙏🏽

[@marianbadea6486]

Does anyone know if my pulse scout need brake fluid

[@Trekopolis]

I read yes

[@diandrewsolee3780]

@Trekopolis Is this ABS?

[@Trekopolis]

Only the front, yes.

[@jabzziijbz69]

Hey, I tried this, but the fluid keeps on squirting out while I'm pumping the brakes, is that normal?

[@Trekopolis]

From the top? If so secure the top lid and pump out fluid until it runs new through, then add more to top as needed to bleed until you see new oil exit tube near brake.

[@jabzziijbz69]

@@Trekopolis thanks, i tried that but there is still no brake pressure

[@Trekopolis]

Make sure the seal is good on the top fluid cap reservoir and close the bleed valve and pump the lever to check pressure after the fluid drains with no bubbles or air. If there's still no pressure you may have a leak somewhere else like a cable or connection. Also be sure to use the proper fluid so it's not too thin like standard oil. Just making sure. :) @@jabzziijbz69

[@remyllebeau77]

@@jabzziijbz69 From what I have seen in other videos, you have to squeeze lever very slowly so it doesn't go out the top.

[@sattyrfrost2277]

Really nice video! Thanks! I have the same brake fluid tank on my Honda, with the same inscriptions. What do you say? I need to refill with brake fluid, but I don't know if it's DOT3 or DOT 4 now in the system... Would it be safe if I add DOT 3&4 type brake liquid? Ride safe! ✌

[@Trekopolis]

As I reference the service manual, Honda recommends DOT 4. I don't know what fluid they use at the factory, but the differences between 3 and 4 can be understood more here: www.differencebetween.net/object/auto-object/difference-between-dot-3-and-dot-4-brake-fluids/ Either one should be fine under normal use, but if you have to change it you can use that information to get a better idea!

[@sattyrfrost2277]

@@Trekopolis thanks for answering. Well then, I think I will get a bottle of DOT4 , and I will completely change the fluid, by bleeding the system multiple times, just to be sure.

[@LegionarHR]

thank you brother its very helpfull !!

[@Mouniraelhouli]

I dont have it on my 110cc honda dirtbike. Is that the only place it is. And my brakes are very slow to stop, especially my back brake, plz help me!

[@Trekopolis]

The back is more than likely a drum brake so it could simply need adjusted or repaired if it's really old. The front brake should have a fluid area so maybe research youtube for the exact model bike or ask AI for any hits on that.

[@Mouniraelhouli]

@@Trekopolis ok thank u, ur the best

[@michaelbrown4447]

Thanks.

[@jackkmanngo]

Great video thank you

[@Trekopolis]

Anytime! ✌🏻

[@blaireofhylia1572]

"Make sure the fluid never goes below that" Okay but it doesn't really have a mark on it, just a circle.. what level is too low??

[@Trekopolis]

The little circle window is a good reference so you can see where the level is at. If you see oil then it's good. If you don't see oil or it's getting close to the bottom of the circle then you can add more fluid. No, there's no mark on the window I don't think, but anything below the circle bubble window is basically letting the rider know it's time to add some fluid.

[@noelbowerman1562]

Actually ,you should not use Phillips head screwdrivers on Japanese bikes as the screws a JIS ,Japanese industry standard. This is why so many people destroy the screws on their bikes.

[@Trekopolis]

Thanks for the info!

[@dfwmetal]

Truth. These are JIS 'plus' heads and a Phillips head will destroy the heads on these screws, especially if they are weathered.

[@BAtadCrazy]

🤔 So simple even I can do it?

[@Trekopolis]

My guess is yes! 😉